Runco DTV-1200 User Manual

OWNER’S MANUAL

DTV-1200

DTV Capable CRT Projector

TABLE OF CONTENTS

1

Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Power Connection to Projector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Source Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

RGB Source to Input 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

RGB Source with Composite Sync to Input 4/5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

RGB Source with Tri-level Sync to Input4/5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Component Source to Input 4/5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

RS-232 Connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Remote Control & Local Keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Stationary Image Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Remote Commands to the Projector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Projector Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Start Up Of The Adjustment Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Adjustment Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Main Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Main Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Image Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Color Adjust . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Format Select . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

EYE-Q Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

EYE-Q Touch Up. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

EYE-Q Auto Converge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Function Keys. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Service Menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Entering The Service Menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Service Menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Random Access Adjustment Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Random Access Adjustment Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Selecting Setup Pattern. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Internal Cross Hatch Pattern . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Random Access Adjustment Mode Selection Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Picture Tuning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Color Balance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Sync Fast/Slow Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Peaking. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Clamp Tuning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Geometry Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Horizontal Phase Adjustments. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Raster Shift Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Left-Right (East-West) Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Left-Side Correction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Top-Bottom (North-South) Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Horizontal Size Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Vertical Linearity Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Vertical Size Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

2

Blanking Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Convergence Adjustments. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Focusing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Color Select . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Service Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Service Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Projector Set-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Run Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Change Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

Change Projector Address. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

Change Baud Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

Projector Warm Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

Warm Up On/Off. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

Warm Up Frequency. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Projector Warm Up Time. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Power Up Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

Common Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

Memory Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Copy a Block. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Deletion of Blocks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

Deleting Block by Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

Deletion of All Blocks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

Set to Midposition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

R & B Convergence Mid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

Undo R & B Convergence Mid. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

Green Convergence Mid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

Undo Green Convergence Mid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

Focus to Midposition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

Undo Focus to Midposition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

East-West to Midposition. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

Undo East-West to Midposition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

North-South Settings to Midposition. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

Undo North-South Settings to Midposition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

Digital Vertical Linearity to Midposition. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

Undo Digital Vertical Linearity to Midposition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

Digital Horizontal Linearity to Midposition. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

Undo Digital Horizontal Linearity to Midposition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

Astigmatism Midposition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

Undo Astigmatism Setting to Midposition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

All Settings to Midposition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

Undo All Settings to Midposition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

Common Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

Dynamic Astigmatism . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

Gamma Corrections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

CRT Run In Cycle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

CRT Drive Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

Memory Banks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

Flyback Turnover Point . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75

Menu Position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75

12C Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

Voltage Diagnostics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

Projector Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

Programmable Function Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78

Programmable Function Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78

Adjustment Blocks and Source Numbers 90-99 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81

Adjustment Blocks (Memory Blocks) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81

Source Numbers 90-99 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81

RS-232 Codes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83

Ceiling/Floor Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87

3

Notice On Safety

This equipment is built in accordance with the requirements of the international safety standards EN60950, UL
1950 and CSA C22.2 No.950, which are the safety standards of information technology equipment including
electrical business equipment.

These safety standards impose important requirements on the use of safety critical components, materials and
isolation, in order to protect the user or operator against risk of electric shock and energy hazard, and having
access to live parts.
Safety standards also impose limits to the internal and external temperature rises, radiation levels, mechanical
stability and strength, enclosure construction and protection against the risk of fire.

Simulated single fault condition testing ensures the safety of the equipment to the user even when the equip­ment's normal operation fails.

4

SAFETY INSTRUCTIONS

Installation Instructions

Before operating this equipment please read this manual thoroughly, and retain it for future reference.
Installation and preliminary adjustments should be performed by qualified Runco personnel or by authorized
Runco service dealers.

Saf

ety Indication On The Product

The lightning flash with an arrowhead within a triangle is intended to tell the user
that parts inside this product may cause a risk of electrical shock to persons.

The exclamation point within a triangle is intended to tell the user that important
operating and/or servicing instructions are included in the technical documentation
for this equipment.

Owner’s Record

The part number and serial number are located at the back side of the projector. Record these numbers in the
spaces provided below. Refer to them whenever you call upon your Runco dealer regarding this product.

SERIAL NUMBER :

DEALER :

Safety Instructions

CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR BACK)

NO USER-SERVICEABLE PARTS INSIDE

REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL

!

!

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

5

Safety Warning

TO PREVENT FIRE OR ELECTRICAL SHOCK HAZARD, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR
MOISTURE

Feder

al Communication Commission (FCC Statement)

This equipment has been tested and found to comply with the limits of a class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required to correct the interference at his own
expense.

Note :

The use of shielded cables is required to comply within the limits of Part 15 of FCC rules and EN55022.

• All the safety and operating instructions should be read before using this unit.

• The safety and operating instructions manual should be retained for future reference.

• All warnings on the equipment and in the documentation manuals should be adhered to.

• All instructions for operating and use of this equipment must be followed precisely.

On Safety

1. This product should be operated from an AC power source.
Power input is autoranging from 100 V(-10%) to 240V(+6%).

2. All equipment in the system is equipped with a 3-wire grounding plug, a plug having a third (grounding) pin.
This plug will only fit into a grounding-type power outlet. This is a safety feature. If you are unable to insert the
plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the purpose of the
grounding-type plug.

WARNING FOR THE CUSTOMERS: THIS APPARATUS MUST BE GROUNDED (EARTHED) via the supplied
3 conductor AC power cable. (If the supplied power cable is not the correct one, consult your dealer.)

A. Mains lead (Power cord) with CEE 7 plug:

The wires of the mains lead are colored in accordance with the following code.

Green and Yellow: earth (safety earth)
Blue: neutral
Brown: line (live)

B. Power cord with ANSI 73.11 plug:

The wires of the power cord are colored in accordance with the following code.

Green/Yellow: ground
White: neutral
Black: line (live)

CEE 7

LINE = BROWN
NEUTRAL = BLUE
GROUND = YELLOW/GREEN

ANSI 73.11

LINE = BLACK
NEUTRAL = WHITE
GROUND = YELLOW/GREEN

3. Do not allow anything to rest on the power cord. Do not locate this product where persons will walk on the

cord. To disconnect the cord, pull it out by the plug. Never pull the cord itself.

4. If an extension cord is used with this product, make sure that the total of the ampere ratings on the products
plugged into the extension cord does not exceed the extension cord ampere rating.

5. Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage­points or short out parts that could result in a risk of fire or electrical shock.

Never spill liquid of any kind on the product. Should any liquid or solid object fall into the cabinet, unplug the set
and have it checked by qualified service personnel before resuming operations.

6. Lightning - For added protection for this video product during a lightning storm, or when it is left unattended
and unused for long periods of time, unplug it from the wall outlet. This will prevent damage to the projector due
to lightning and AC power-line surges.

Caution on Fire Hazard

Do not place flammable or combustible materials near projector !
Runco large screen projection products are designed and manufactured to meet the most stringent safety regu-

lations. This projector radiates heat on its external surfaces and from ventilation ducts during normal operation,
which is both normal and safe.
Exploding, flammable or combustible materials into close proximity of this projector could result in the sponta­neous ignition of that material, resulting in a fire. For this reason, it is absolutely necessary to leave an "exclu­sion zone" around all external surfaces of the projector whereby no flammable or combustible materials are
present. Do not cover the projector with any material while the projector is in operation.

Keep flammable and combustible materials away from the projector at all times. Mount the projector is a well
ventilated area away from sources of ignition and out of direct sun light. Never expose the projector to rain or
excessive moisture. In the event of fire, use sand, CO2, or dry powder fire extinguishers; never use water on an
electrical fire.
Always have service performed on this projector by authorized Runco service personnel. Always insist on gen­uine Runco replacement parts. Never use non-Runco replacement parts as they may degrade the safety of this
projector.

On Installa

tion

1. Do not place this equipment on an unstable cart, stand, or table. The product may fall, causing serious
damage to it.

2. Do not use this equipment near water.

3. Slots and openings in the cabinet and the back or bottom are provided for ventilation; to ensure reliable oper-

ation of the product and to protect it from overheating, these openings must not be blocked or covered. The
openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This
product should never be placed near or over a radiator or heat register.

The projector should not be placed in a built-in installation or enclosure unless proper ventilation is provided.

4. Do not block the projector cooling fans or free air movement under and around the projector. Loose papers or
other objects may not be nearer to the projector than 4" on any side.

6

7

On Servicing

Do not attempt to service this product yourself, as opening or removing covers may expose you to dangerous
voltage potentials and risk of electric shock!

Refer all servicing to qualified service personnel.
Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following

conditions:
a. When the power cord or plug is damaged or frayed.

b. If liquid has been spilled into the equipment.
c.If the product has been exposed to rain or water.
d. If the product does not operate normally when the operating instructions are followed.
Note: Adjust only those controls that are covered by the operating instructions since improper adjust
ment of the other controls may result in damage and will often require extensive work by a qualified
technician to restore the product to normal operation.
e. If the product has been dropped or the cabinet has been damaged.
f. If the product exhibits a distinct change in performance, indicating a need for service.

Replacement parts - When replacement parts are required, be sure the service technician has used original
Runco replacement parts or authorized replacement parts which have the same characteristics as the Runco
original part. Unauthorized substitutions may result in degraded performance and reliability, fire, electric shock or
other hazards. Unauthorized substitutions may void warranty.

Safety check - Upon completion of any service or repairs to this projector, ask the service technician to perform
safety checks to determine that the product is in proper operating condition.

On Cleaning

Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a
damp cloth for cleaning.

- To keep the cabinet looking brand-new, periodically clean it with a soft cloth. Stubborn stains may be removed
with a cloth lightly dampened with mild detergent solution. Never use strong solvents, such as thinner or ben­zine, or abrasive cleaners, since these will damage the cabinet.

- To ensure the highest optical performance and resolution, the projection lenses are specially treated with an
anti-reflective coating, therefore, avoid touching the lens. To remove dust on the lens, use a soft dry cloth.

On Repacking

Save the original shipping carton and packing material; they will come in handy if you ever have to ship your
equipment. For maximum protection, repack your set as it was originally packed at the factory.

On Illumina

tion

In order to obtain the best quality for the projected image, it is essential that the ambient light which is allowed to
fall on the screen be kept to an absolute minimum. When installing the projector and screen, care must be taken
to avoid exposure to ambient light directly on the screen. Avoid adverse illumination on the screen from direct
sunlight or fluorescent lighting fixtures. The use of controlled ambient lighting, such as incandescent spot light or
a dimmer, is recommended for proper room illumination. Where possible, care should also be taken to ensure
that the floors and walls of the room in which the projector is to be installed are non-reflecting, dark surfaces.
Brighter surfaces will tend to reflect and diffuse the ambient light and hence reduce the contrast of the projected
image on the screen.

8

LIMITED WARRANTY

Congratulations on your purchase of a Runco video product and welcome to the Runco family! We
believe Runco produces “The World’s Finest Home Theater Products”. With proper installation, setup
and care, you should enjoy many years of unparalleled video performance. Please read this consumer
protection plan carefully and retain it with your other important documents.

This is a LIMITED WARRANTY as defined by the U.S. Consumer Product Warranty and Federal Trade
Commission Improvement Act.

WHAT IS COVERED

UNDER THE TERMS OF THIS WARRANTY:

SERVICE LABOR: Runco will pay for service labor by an approved Runco service center when need­ed as a result of manufacturing defect for a period of two (2) years from the effective date of delivery to
the end user.

PARTS (Not including projector lamp): Runco will provide new or rebuilt replacement parts for the parts
that fail due to defects in materials or workmanship for a period of two (2) years from the effective date
of the warranty. Such replacement parts are then subsequently warranted for the remaining portion (if
any) of the original warranty period.

LAMP: Six months or 1000 hours (which ever comes first).

WHAT IS NOT

COVERED UNDER THE TERMS OF THIS WARRANTY:

This warranty only covers failure due to defects in materials and workmanship that occur during normal
use and does not cover normal maintenance. This warranty does not cover cabinets or any appearance
item; any damage to laser discs; failure resulting from accident, misuse, abuse, neglect, mishandling,
misapplication, faulty or improper installation or setup adjustments; improper maintenance, alteration,
improper use of any input signal; damage due to lightning or power line surges, spikes and brownouts;
damage that occurs during shipping or transit; or damage that is attributed to acts of God. In the case
of remote control units, damage resulting from leaking, old, damaged or improper batteries is also
excluded from coverage under this warranty.

CAUTION: DAMAGE RESULTING DIRECTLY OR INDIRECTLY FROM IMPROPER INSTALLATION
OR SETUP IS SPECIFICALLY EXCLUDED FROM COVERAGE UNDER THIS WARRANTY. IT IS
IMPERATIVE THAT INSTALLATION AND SETUP WORK BE PERFORMED ONLY BY AN AUTHO­RIZED RUNCO DEALER TO PROTECT YOUR RIGHTS UNDER THIS WARRANTY. THIS WILL ALSO
ENSURE THAT YOU ENJOY THE FINE PERFORMANCE YOUR RUNCO PRODUCT IS CAPABLE OF
PROVIDING WHEN INSTALLED AND CALIBRATED BY RUNCO AUTHORIZED PERSONNEL.

RIGHTS, LIMITS AND EXCLUSIONS:

Runco limits its obligations under any implied warranties under state laws to a period not to exceed the
warranty period. There are no express warranties. Runco also excludes any obligation on its part for
incidental or consequential damages related to the failure of this product to function properly. Some
states do not allow limitations on how long an implied warranty lasts, and some states do not allow the
exclusion or limitation of incidental or consequential damages. So the above limitations or exclusions
may not apply to you. This warranty gives you specific legal rights, and you may also have other rights
that vary from state to state.

Limited Warranty

9

EFFECTIVE WARRANTY DATE:

This warranty begins on the effective date of delivery to the end user. For your convenience, keep the
original bill of sale as evidence of the purchase date.

IMPORTANT: WARRANTY REGISTRATION:

Please fill out and mail your warranty registration card. It is imperative that Runco knows how to reach
you promptly if we should discover a safety problem or product update for which you must be notified.

TO OBTAIN SERVICE, CONTACT YOUR RUNCO DEALER:

Repairs made under the terms of the Limited Warranty covering your Runco International video product
will be performed at the location of the product, during usual working hours, providing location of prod­uct is within normal operating distance from a Runco Authorized Service Center. If, solely in Runco’s
judgement, location of product to be repaired is beyond normal operating distance of the closest Runco
Authorized Service Center, it is the owner’s responsibility to arrange for shipment of the product for
repair. These arrangements must be made through the selling Runco dealer. If this is not possible, con­tact Runco directly for a return authorization number and shipping instructions. Runco will return prod­uct transportation prepaid in the United States, unless no product defect is discovered. In that instance,
shipping costs will be the responsibility of the owner.

ADDITIONAL INFORMATION:

To locate the name and address of the nearest Runco Authorized Service location, or for additional infor­mation about this warranty, please call, write or visit our website:

CUSTOMER SERVICE DEPARTMENT

RUNCO INTERNATIONAL

2900 Faber Street

Union City, CA 94587

Ph: [phone] / Fax: [phone]

www.runco.com

10

CONNECTIONS

Power Connection to Projector

AC Power (Mains) Cord Connection

Use the supplied power cord to connect your Projector to the wall outlet. Plug the female power connector into
the male connector at the rear side of the Projector.

Power Check

The power voltage is autoranging between 100V(-10%) and 240V (+6%).

Switching On/Off

The Projector is switched ON and OFF using the power (mains) switch ON/OFF.
Pushed In: ON

Out: OFF
The Projector can start in the operational mode (ON) or in the stand by mode, depending on the power up set-

ting in the service mode.
Stand by indication lamp :
OFF: Projector switched OFF

Green: Projector is ON
Red: Projector is in Standby Mode.

When turning ON the Projector, it can start up in two ways if the "CRT run in" cycle option is switched OFF.

- full white image (projector warm up) or

- immediate image display.

This option can be enabled in the service mode (see page 72).

OFF ON

AC Input

Future Expansion

RG

B

INPUT 4/5

OFF ON

HV

S-Video

INPUT 2

AC Input

OFF/ON
75 Ohm

OFF/ON
75 Ohm

Green: Operation
Red: Standby

12 Volt
Trigger

Video

Status

INPUT 1

OFF/ON

Video

12 Volt
Trigger

75 Ohm

Status

Green: Operation
Red: Standby

INPUT 1

11

Source Connections

Input Facilities

The following source types can be connected to the inputs :

• RGB Tri-level Sync

• RGB Composite, Separate or Sync on green

• Component Video

• Component Video with Tri-level Sync

Which source to which input

Source No. Projector Input Remote Button No.

1 Comp. Video* 1 (not used)
2 S-Video/Comp. Video* 2 (not used)
3 RGB 3
4/5 RGB 4 or 5
4/5 Component Video 6
4/5 RGB with Tri-level Sync 7
4/5 Component Video

with Tri-level Sync 8

* Not used in the DTV-1200

1

2543

OFF ON

AC Input

Future Expansion

RG

B

INPUT 4/5

HV

S-Video

INPUT 2

OFF/ON
75 Ohm

Video

INPUT 1

12 Volt
Trigger

OFF/ON
75 Ohm

Status

Green: Operation
Red: Standby

RGB Source to Input 3

12

Which signal to Input 3

Connect your RGB source with sync on green, composite or separate sync via an interface to Input 3.
Always use an interface when a computer and local monitor have to be connected to the projector as the signal
cable coming from the computer is limited to 60 cm due to interferences.

Pin conf

iguration D9 connector of the Analog input.

1 Not connected
2 Ground RGBS
3 RED
4 GREEN
5 BLUE
6 Ground RGBS
7 Ground RGBS
8 Hor/comp. sync
9 Vert. sync

Input Select Input 3

With the Remote, press button 3

Which signal to Input 4/5

RGB input terminals with separate H and V Sync inputs, Composite Sync Input or with Sync on green (BNC ter­minals). The Projector detects automatically where the sync signal is located. This is the Input where Video
Processors (such as the Runco VHD-4404 Ultra) or high definition sources should be connected.

RGB Source with Composite Sync to Input 4/5

RGB Sync on green or separate Sync Input selection

With the remote, press:

- Button 4 for Sync on green

- Button 5 for Separate Sync

AC Input

B

OFF ON

Future Expansion

ANALOG INTERF. 120MHz

ON
OFF

R

RG

INPUT

H

B

G

V

INP

75 ohm term.

inver.

HV

INPUT 4/5

INP

S-Video

INPUT 2

OFF/ON
75 Ohm

Video

INPUT 1

12 Volt
Trigger

OFF/ON
75 Ohm

Status

Green: Operation
Red: Standby

OFF ON

AC Input

Future Expansion

4404 ULTRA

O

C

UN

R

MULTIFILM

RG

B

INPUT 4/5

HV

S-Video

INPUT 2

OFF/ON
75 Ohm

OFF/ON
75 Ohm

Green: Operation

Status

Red: Standby

12 Volt
Trigger

Video

INPUT 1

n

e

u

M

13

RGB Source with Tri-level Sync to Input 4/5

Which signal to Input 4/5

RGB input terminals with Tri level sync input or with Tri-level sync on green (BNC terminals). The projector
detects automatically where the sync signal is located.

R

GB3S or RG3sB input selection

With the remote, press digit button 7

Component Source to Input 4/5

Which signal to Input 4/5

(R-Y)Y(B-Y) input terminals with sync input or with sync on the luminance (Y) input (BNC terminals). The pro­jector detects automatically where the sync signal is located.

Component

Video input selection

With the remote, press digit button 6

RS-232 Connection

RS-232 input and RS-232 output of the Projector.

The projector is equipped with a RS-232 port that allows communication with an automation system such as
AMX, Crestron, etc.

Applications

a) remote control:

- allow storage of multiple projector configurations and set ups.

- wide range of control possibilities.

- address range from 0 to 255.

b) data communications:

- sending data to the projector or copying the data from the projector to a hard memory device.

Set up of the Baud Rate for Communication with a Computer.

See 'Changing the Baud Rate' in chapter 'Service Mode'.

14

GETTING STARTED

Battery Installation in the Remote

Two batteries are packed together with the Remote. Before using your Remote, install first these batteries.
1 Remove the battery cover on the backside by pushing the handle a little towards the bottom of the Remote.

2 Lift up the top side of the cover at the same time.
3 Insert the batteries as indicated in the Remote.
4 Put the battery cover on its place.

Ho

w to replace the batteries in the Remote?

To replace the batteries :
1 Remove the battery cover on the backside by pushing the handle a little towards the bottom of the Remote.

2 Lift up the top side of the cover at the same time.
3 Push on the + side of the battery towards the - side
4 Lift up the battery at the same time.
5 Repeat for the second battery.
6 Insert the batteries as indicated in the Remote (battery type AAor LR6 or equivalent).
7 Put the battery cover on its place.

Note: only important if more than one projector is installed in the room :

1. The default address is zero (0) or (1). The standard Remote is setup for common address zero.

To change the common address of the Remote, contact a Runco service center. If it is necessary to program
the projector address into the Remote, see 'Projector Address'.

2. Projector address has to be reprogrammed everytime the battery is changed, the Remote will always switch
to the default address.

Remote Control & Local Keypad

15

Overview of Functions

This remote control includes a battery powered infrared (IR) transmitter that allows the user to control the
projector remotely.
This remote control is used for source selection, control, adaptation and set-up.
It includes automatic storing of:

- picture controls (Brightness, Sharpness,....)

- settings

Other functions on the control units are:

- switching between standby and operational modes

- switching to "pause" (picture mute)

- direct access to all connected sources

1

8

7
6

5
4
3

2

1

1 Function keys: user programmable keys with functions for direct access.
2 ADJ: ADJUST key, to enter or exit the adjustment mode.
3 Address key (recessed key): to enter the address of the projector (between 0 and 9).

Press the recessed address key with a pencil, followed by pressing one digit button between 0 and 9.

4 not used
5 PAUSE: mutes the projected image.
6 STBY: stand-by button, toggles power On/Off (Stby).
7 not used
8 not used
9 Digit buttons: direct input selection.
10 Audio controls: not used
11 Picture controls: use these buttons to obtain the desired picture.
12 PHASE: not used.

standby

pause/park

sharpness

tint

color

brightness

contrast

1

F3

1

F2

F1

F4

F5

2

ADJ

EXIT

1

3
4
5

6

PAUSE

7
8

9

0

0

9

8

7

6

5

34

2

1

TREBLE BALANCE

BASS

ENTER

TEXT

PHASE

SHARPN

TINT

COLOR

BRIGHTN

CONTR

VOL

1
1

1
1

1

1

13 FREEZ: press to freeze the projected image.
14 TEXT: when adjusting one of the image controls, e.g. contrast, during a meeting, the displayed bar scale

can be removed by pressing 'TEXT' key first. To re-display the bar scale on the screen, press 'TEXT' key again.

15 ENTER: to start up the adjustment mode or to confirm an adjustment or selection in the adjustment mode.
16 Cursor Keys: to make menu selections when in the adjustment mode.or to increase or decrease the analog

level of the image controls when they are first selected.

17 EXIT: to leave the adjustment mode or to scroll upwards when in the adjustment mode.
18 IR Output LED: lights up when a button on the remote control is pressed. (This is a visual indicator to

check the operation of the remote control)

16

Start Up

Press the Power button on the remote; ensure the main Power button on the rear of the Projector is pressed in.
When this warm up cycle message appears on the screen, the menu offers the possiblity to start with a warm

up period (press ENTER) or to skip this cycle (press EXIT). The number of minutes and the horizontal frequecy
can be programmed in the 'Service mode' under the item 'Projector Set Up'.
Note: This warm up period is built in so that the Projector can quickly reach its operating temperature.

When starting this warm up period, a full white image is shifted on the CRT faceplate to avoid a burn in. Every
30 seconds a text box will be displayed on another place on the screen with the remaining time to go.
The image dimensions can be adjusted with the cursor keys to avoid scanning on the edges of the CRT's.

PROJECTOR WARM UP

A FULL WHITE PATTERN WILL BE

GENERATED FOR x MIN.

FOR IMMEDIATE USE OF THE

PROJCTOR, PRESS <EXIT>
WARNING : SKIPPING THIS

PROCEDURE CAN REDUCE THE

INITIAL PICTURE QUALITY OF THE

PROJECTED IMAGE;

YOU CAN ADJUST THE IMAGE

DIMENSTIONS WITH THE ARROW

KEYS TO AVOID SCANNING ON THE

EDGES OF THE CRT'S;

THIS OPTION CAN BE DISABLED IN

THE SERVICE MENU

with <ENTER>

<EXIT> to return

To interrupt the warm up period:
1 Press EXIT, the warm up menu will be redisplayed with the remaining time indication.
2 Press EXIT again to quit the warm up cycle and to display the source.

Star

t Up in a Specific Source

When the Projector is in Standby, it can be turned ON with a specific source. To do this, simply press the source
number button (see page 19).

Stationary Image Warning

Do not display a stationary image with full brightness and contrast for longer than 10
minutes, otherwise you risk damage to the CRT's.

!

Remote Commands to the Projector

Pointing the Remote to the reflective screen

Point the front of the Remote to the screen surface.

Point the front of the Remote towards one of the IR sensors in the projector.

or

When using the wireless remote control, make sure you are within the effective operating distance (30m, 100ft
in a straight line). The remote control unit will not function properly if strong light strikes the sensor window or if
there are obstacles between the remote control unit and the projector's IR sensor.

R

emote used in a hardwired configuration.

17

Plug one end of the remote cable in the
connector on the bottom of the Remote and
the second side in the connector in the rear
panel of the projector labelled 'REMOTE'.

Ceiling

Screen

IR sensor

Remote

Front of projector

45°

45°

F3

F2

F4

F5

F1

ADJ

EXIT

ENTER

PAUSE

TEXT

PHASE

0

9

SHARPN

8

7

TINT

6

5

COLOR

34

BRIGHTN

2

1

CONTR

TREBLE BALANCE

BASS

VOL

Remote

Rear side of project

PORT 4/5

9

7

5

34

1

TREBLE BALANCE

"ThisdevicecomplieswithPart15of

Operationissubjectto

followingtwo conditions:(1)This

the FCC Rules.

devicemaynotcause harmfulinter-

green : operation

Comp-/H-Sync V-Sync

S-VIDEO OFF - ON

VIDEO

OFF - ON

ference,and(2) thisdevicemust

red : standby

acceptany interferencereceived,
includinginterferencethatmaycause

75 Ohm

75 Ohm

PORT 1

PROJECTOR MODE

undesired operation"

PORT 2

45°

F3

F2

F4

F5

EXIT

ENTER

PAUSE

TEXT

PHASE

0

SHARPN

8

TINT

6

COLOR

BRIGHTN

2

CONTR

BASS

VOL

See installation instructions before connecting to the supply.
Voir la notice d'installation avant de raccorder au réseau.

V-nom

800 peripherals

I-nom

ONOFF

120/230 V

Freq

7/5 Amp

POWER / MAINS

COMM. PORT PORT 3

50/60 Hz

RGB

45°

F1

ADJ

RS232 IN

RS232 INRS232 OUT

RS232 OUT

IR

IR

REMOTE

REMOTE

18

Projector Address

Why a projector address?

Since more than one projector can be installed in a room, the separate projectors can be separately address­able with a Remote or a computer.

Set up an Indi

vidual Projector Address

The set up of a projector address can be done via the software.
See 'Change Projector Address' in Chapter 'Service Mode'

Ho

w to control the projector or projectors?

The projector's address may be set to any value between 0 and 255 which can be set in the Service Mode.
When the address is set, the projector can be controlled now with:

- the Remote for addresses between 0 and 9.

- a Control System for addresses between 0 and 255.

Note: A projector will respond to a Remote set to the common address ('0' or '1') regardless of what address is
set in the projector itself.

Common

Address

Every projector has a common address '0' or '1'. The choice between '0' and '1' can be selected in the Service
mode.

Bef

ore using the Remote

The Remote is default programmed with address 0 or 1, 'common address'. With that 'common address' pro­grammed into the Remote, every projector, with the same common address set up, will listen to the commands
given by this Remote. If it is necessary to control a specific projector, than enter the projector address into the
Remote (only when that address is between 0 and 9). The projector with the corresponding address will listen to
that specific Remote.

Displa

y the Projector Address on the Screen.

Press the ADDRESS key (recessed key on the Remote) with a pencil. The projector's address will be displayed
in a 'Text box' (menu 1). This text box disappears after a few seconds.

To continue using the Remote with that specific address, it is necessary to enter the same address with the digit
buttons (address between 0 and 9) within 5 seconds after pushing the address key. For example: if the Address
key displays projector address 003, then press "3" digit button on the Remote to set the Remote's address to
match the projector's address. Do not press 003 digits. This will address the remote control to '0' and control all
projectors in the room.
If the address is not entered within 5 seconds, the Remote returns to its default address (zero address) and
control all projectors in the room.

Ho

w to program an address into the Remote?

Press the ADDRESS key (recessed key on the Remote) with a pencil and enter the address with the digit but­tons within 5 seconds after pushing the address key. That address can be any digit between 0 and 9.

PROJECTOR ADDRESS
001

19

Input selection modes

Source No. Projector Input Remote Button No.

3 RGB 3
4/5 RGB (HV, S.O.G) 4 or 5
4/5 Component Video 6
4/5 RGB with Tri level sync 7
4/5 Component Video with

Tri-level sync 8

Input Selection via the Remote.

With the digit buttons, it is possible to select one of the above input modes.

W

hen the source is selected

When a valid and available source is selected, there will be information displayed on the screen about that
source. This information includes:

- Source number

- Horizontal frequency

- Vertical frequency

When the entry is a non valid source number, a warning appears on the screen: 'input not available'.

When a valid source number is selected, the projector will display this source or it will wait on the selected
source number until the source becomes available. Amessage 'source not available' will be displayed for a
short time.

When a Video or S-Video source is selected and no decoder is installed, the projector displays the folllowing
message: 'Option not installed'.

Source 02
Fh= 63 kHz
Fv= 60 Hz

WARNING
Input not
available

WARNING
Source not
available

WARNING
Option not

installed!

20

Picture Controls

The control keys are located on the right side of the key panel of the Remote and indicated with the name of the
control and an icon.

When an image control is pressed, a text box with bar scale and the function name of the control, e.g. 'bright­ness...' appears on the screen (only if text is ON). The length of the bar scale indicates the current memorized
setting for this source. The bar scale changes as the + or - side of the button of the control are pressed.

Brightness Control:

A correct 'brightness' setting is important for good image reproduction. Adjust the brightness with the + button
and - button until the darkest parts of the picture appear black.

A bar scale gives a visual indication on the screen of the current brightness setting while pressing on the above
indicated buttons. If the bar scale is not visible on the screen, press 'TEXT' once and retry the above indicated
buttons.

The bar scale increases when pressing on the + button (higher brightness) and decreases when pressing on the

- button (lower brightness).

Contrast Control:

A correct 'contrast' setting is important for good image reproduction.
Adjust the contrast to the level you prefer, according to room lighting conditions.
A bar scale gives a visual indication on the screen of the current contrast setting while pressing the + or - but­tons . If the bar scale is not visible on the screen, press 'TEXT' key once and retry the above indicated buttons.
The bar scale increases when pressing on the + button (higher contrast) and decreases when pressing on the ­button (lower contrast).

Color Saturation Control: Not used on the DTV-1200
Tint Control: Not used on the DTV-1200
Sharpness Control: Not used on the DTV-1200

Sound Contr

ols: Not used on the DTV-1200

T

he Pause Key

The ‘Pause’ button mutes the projected image. When Pause is pressed, the image will disappear until it is
pressed again.

T

he Freeze Key

When the Freeze key is pressed, the image is frozen until this key is pressed again.

21

START UP OF THE ADJUSTMENT MODE

Start Up

All picture adjustments are made while in the 'Adjustment mode'.
Press the ADJUST key.

The projector displays the 'Main menu' (menu 1).

menu 1
You are now in the 'Adjustment mode'. The cursor keys are used to make menu selections and also vertical and

horizontal adjustments. The ENTER and EXIT keys are used to move forward and backward through the menu
structure. The ADJUST key can be used to terminate the adjustment mode while a path selection menu (head
menu) is displayed.

P

ossible Paths

Depending on the projector configuration the following paths are possible with the 'Main menu'.
Image Control - Allows you to change the color temperature of the image and to select another format (adjust-

ment) for the image.
Eye-Q Control - This control allows to align the projector automatically using the autoconvergence unit EYE-Q

built into the projector.

Function Keys - Gives an overview of the programmed function for each key.
Service Menus - Installation and adjustment menus to set up the projector. Before entering a warning will be

displayed.

Adjustment Mode

MAIN MENU

Image Control
Eye-Q
Function Keys

Service Menus

Select with or
then <ENTER>
<EXIT> to return

22

MAIN MENU

Overview Flowchart

Main Menu

MAIN MENU

IMAGE CONTROL

EYE-Q CONTROL

FUNCTION KEYS

SERVICE MENUS

FORMAT SELECT

COLOR ADJUST

EYE-Q TOUCH UP

EYE-Q AUTO CONVERGE

EYE-Q FULL ALIGNMENT

F2

F3

F4

F5

EYE-Q

GUIDED

RANDOM ACCESS

INSTALLATION

SERVICE

F1

Image Control

Starting Up

1 Push the cursor keys é or ê to select 'Image Control' (menu 1).

The selected item will change in color and a marker will be displayed in front of it.

2 Press ENTER to select.

The 'Image Control' menu will be displayed (menu 2a).

menu 1 menu 2a

MAIN MENU

Image Control
Eye-Q
Function Keys

Service Menus

Select with or
then <ENTER>
<EXIT> to return

IMAGE CONTROL

Image Processing
Color Adjust
Format Select

Select with or
then <ENTER>
<EXIT> to return

Color Adjust

What can be done?

The color temperature of the image can be installed. The customer has the choise between 4 factory preset
color temperatures and one custom. This custom color temperature has to be adjusted in the 'Random Access
Adjustment Mode'.

Ho

w to select 'Color Adjust' and to select a new color temperature?

1 Push the cursor keys or to select 'Color Adjust' (menu 1).
2 Press ENTER to display the Color Adjust menu (menu 2).
3 Push the cursor keys or to select the desired color temperature.
4 Press ENTER to activate that color temperature.

menu 1 menu 2

IMAGE CONTROL

Image Processing
Color Adjust
Format Select

Select with or
then <ENTER>
<EXIT> to return

COLOR ADJUST

Broadcast 3200 oK
Film 4900 oK
Video 6500 oK
Computer 9300 oK

Custom

Select with or
then <ENTER>
<EXIT> to return

23

24

What can be done?

For one source, up to 8 different sets of settings can be stored. A set of settings is called 'Format'.
A 'Format' can be 'available' or 'free'.
'Available' when settings are stored in this location.
'Free' when no setting are stored in this location. This location can be used for storing new adjustment settings
for this source.
When 'available', a name of 8 characters can be programmed by the user.

Ho

w to select a 'Format' ?

1 Push the cursor keys or to select 'Format Select' (menu 1).
2 Press ENTER to display the Format List (menu 2).
3 Push the cursor keys or to select the desired ‘Format’.
4 Press ENTER to select.

menu 1

menu 2

Format Select

IMAGE CONTROL

Image Processing
Color Adjust
Format Select

Select with or
then <ENTER>
<EXIT> to return

FORMAT LIST

Source 01 VIDEO
Format 1 Available xxxxxxxxxx
Format 2 Free xxxxxxxxxx
Format 3 Available xxxxxxxxxx
Format 4 Free xxxxxxxxxx
Format 5 Free xxxxxxxxxx
Format 6 Free xxxxxxxxxx
Format 7 Free xxxxxxxxxx
Format 8 Free xxxxxxxxxx

Select with or
then <ENTER> to select
<EXIT> to return
<TEXT> to enter a name

25

How to add a name to a 'Format'?

1 Push the cursor keys or to select the Format to which a name has to be added (menu 1).
2 Press TEXT to display the compose menu (menu 2).
3 The position of the character which will be edited, will be indicated with a digit. Push the cursor keys

, , or to select the first character.

4 Press ENTER to select the choosen character. This character will be inserted on the indicated position.

The 'edit character' indication will be incremented with one.
5 Continue in the same way for the other characters.
6 When the name is completed, press EXIT to return to the 'Format List' menu (menu 3).

menu 1 menu 2

menu 3

FORMAT LIST

Source 01 VIDEO
Format 1 Available xxxxxxxxxx
Format 2 Free xxxxxxxxxx
Format 3 Available xxxxxxxxxx
Format 4 Free xxxxxxxxxx
Format 5 Free xxxxxxxxxx
Format 6 Free xxxxxxxxxx
Format 7 Free xxxxxxxxxx
Format 8 Free xxxxxxxxxx

Select with or
then <ENTER> to select
<EXIT> to return
<TEXT> to enter a name

COMPOSE

A B C D E F G H I

J K L M N O P Q R
S T U V W X Y Z
/ : ­0 1 2 3 4 5 6 7 8 9

XXXXXXXXXX

Edit character 1

Select with or
then <ENTER>
<EXIT> to return

FORMAT LIST

Source 01 VIDEO
Format 1 Available xxxxxxxxxx
Format 2 Free xxxxxxxxxx
Format 3 Available xxxxxxxxxx
Format 4 Free xxxxxxxxxx
Format 5 Free xxxxxxxxxx
Format 6 Free xxxxxxxxxx
Format 7 Free xxxxxxxxxx
Format 8 Free xxxxxxxxxx

Select with or
then <ENTER> to select
<EXIT> to return
<TEXT> to enter a name

26

How to store the settings to a new 'Format'?

1 Push the cursor keys or to select a free format.
2 Press ENTER to activate.
3 Make any adjustment to the image.
4 Quit the adjustment mode by pressing ADJUST.

The selected format will change from free to available.

With the Eye-Q functions it is possible to automatically adjust the convergence of the image.

Star

t Up

1 Push the cursor keys or to select 'EYE-Q control' (menu 1).

The selected item will change in color and a marker will be displayed in front of it.

2 Press ENTER to select.

The 'EYE-Q control' menu will be displayed (menu 2).

menu 1 menu 2
Note: Before starting one of the EYE-Q functions, be sure the projector has warmed up for at least 20 min.

W

hat can be done?

If you discover in the middle of the image a convergence misalignment between red, green and blue, the static
convergence of this currently selected source can be adjusted with the touch up function.

Eye-Q Control

MAIN MENU

Image Control
Eye-Q
Function Keys

Service Menus

Select with or
then <ENTER>
<EXIT> to return

EYE-Q CONTROL

EYE-Q Touch Up
EYE-Q Auto Converge

Select with or
then <ENTER>
<EXIT> to return

Eye-Q Touch Up

27

How to start up the EYE-Q Touch Up?

1 Push the cursor keys or to select 'EYE-Q Touch Up' (menu 1).
2 Press ENTER to activate the touch up function.

The process starts and when successfully completed, the projector will return to image display of the
current source.

menu 1

EYE-Q CONTROL

EYE-Q Touch Up
EYE-Q Auto Converge

Select with or
then <ENTER>
<EXIT> to return

Eye-Q Auto Converge

What can be done?

The autoconvergence on the current source will be carried out automatically, starting from the existing settings.
By projecting alternately red and blue lines, 25 convergence areas are aligned onto the green pattern.

Ho

w to start up the EYE-Q Auto Converge?

1 Push the cursor keys or to select 'EYE-Q Auto Converge' (menu 1).
2 Press ENTER to activate the autoconvergence function.

The process starts and when successfully completed, the projector will return to image display of the
current source.

menu 1

EYE-Q CONTROL

EYE-Q Touch Up
EYE-Q Auto Converge

Select with or
then <ENTER>
<EXIT> to return

Function Keys

28

What can be done?

Quick access keys to customer pre-programmed adjustments. Almost any adjustment can be added to a func­tion key. To program a function key, it is necessary to enter into the 'Service Menu'. To activate a function key,
just press the corresponding key.
The following functions are factory pre-programmed :

F1 = EYE-Q Touch up
F2 = Convergence Red on Green
F3 = Convergence Blue on Green
F4 = H & V Size
F5 = Color Balance

Ho

w to get an overview of the programmed keys?

1 Push the cursor keys or to select 'Function Keys' (menu 1).
2 Press ENTER to display an overview of the function keys (menu 2).
3 Press EXIT to return.

MAIN MENU

Image Control
Eye-Q
Function Keys

Service Menus

Select with or
then <ENTER>
<EXIT> to return

Service Menus

What can be done?

With the complete set of Service menus such as EYE-Q, Guide, Random Access, Installation and Service it is
possible to adjust the projector completely.
When entering the Service Menus, a warning will be displayed mentioning that only qualified Runco service
personnel may enter the Service menus.

Ho

w to enter the Service Menu?

1 Push the cursor keys or to select 'Service Menus' (menu 1).
2 Press ENTER to select. Awarning will be displayed (menu 2). "Risk of incorrect adjustment of the

projector. The following SERVICE menus are reserved to and to be performed only by qualified
personnel! If qualified, press <ENTER> to continue, or if not, <EXIT> to return.

MAIN MENU

Image Control
Eye-Q
Function Keys

Service Menus

Select with or

then <ENTER>

<EXIT> to return

WARNING

RISK OF INCORRECT ADJUSTMENT
OF THE PROJECTOR.

The following SERVICE menus are reserved to,
and to be performed only by qualified personnel !

If qualified, press
<ENTER> to continue, or
if not, <EXIT> to return.

FUNCTION KEYS

F1: EYE-Q Touch Up
F2: Convergence Red on Green
F3: Convergence Blue on Green
F4: H & V Size
F5: Color Balance

<EXIT> to return

menu 2menu 1

menu 1

menu 2

ADJUSTMENT MODE

Select a path from below:

EYE-Q

GUIDED

RANDOM ACCESS

INSTALLATION

SERVICE

Source 1

Select with or

then <ENTER>

<EXIT> to return

menu 3

29

ENTERING THE SERVICE MENUS

Service Menus

What is available in the Service menus?

A complete set of adjustments divided in different modes are available to adjust the projector
The different mode are:
EYE-Q: to autoconverge the projector.

Guided : Guided should be selected if the user intends to perform a complete alignment of the projected image
and is not extensively familiar with the projector. All the necessary geometry and convergence adjustments are
executed in a predetermined sequence.

Random Access: Random Access should be selected if the user intends to make only a few adjustments or if
the user is highly qualified and knows the sequence of adjustments.

Installation: Installation should be selected if the projector has been relocated and/or a different screen size is
desired.

Service: Service should be selected if the user intends to change predefined settings.

Ho

w to enter the Service Menus?

1 Press the ADJUST key.

The projector displays the 'Main menu' (menu 1).
2 Push the cursor keys or to select 'Service Menus'
3 Press ENTER to select.

A warning will be displayed (menu 2).
4 If qualified, press ENTER to continue

The Service menus main menu will be displayed (menu 3).

MAIN MENU

Image Control
Eye-Q
Function Keys

Service Menus

Select with or

then <ENTER>

<EXIT> to return

WARNING

RISK OF INCORRECT ADJUSTMENT
OF THE PROJECTOR.

The following SERVICE menus are reserved to,
and to be performed only by qualified personnel !

If qualified, press
<ENTER> to continue, or
if not, <EXIT> to return.

menu 1

menu 2

ADJUSTMENT MODE

Select a path from below:

EYE-Q

GUIDED

RANDOM ACCESS

INSTALLATION

SERVICE

Source 1

Select with or

then <ENTER>

<EXIT> to return

menu 3

30

Password Protection

Some items in the Adjustment mode are password protected. While selecting such an item, the projector asks
to enter your password. (Password protection is only available when the password strap on the contoller module
is ON. Contact an authorized Runco technician when no password is requested during the adjustment proce­dure and password protection is desired.)

Entering the P

assword

Your password contains 4 digits.
Enter the digits with the numeric keys on the Remote.
Example : 1 1 1 1
For each digit entered, a 'X' appears on the screen under the displayed text 'enter password'.
When the password is correct, you gain access to the selected item.

When the entered password is wrong, the error message 'wrong password !!!' will be displayed.

Note:

When the password is correctly entered, all other password protected items are accessible without re-entering
the password.
When re-entering the adjustment mode, it will be necessary to enter your password again when selecting a
password protected item.

enter

password

x x x x

31

RANDOM ACCESS ADJUSTMENT MODE

Starting Up

Push the cursor keys up or down to highlight "RANDOM ACCESS" and then press ENTER.
Some items in the Random access mode are password protected (when the password function is enabled).

Enter your password to continue. All other password protected items are now also available if you stay in the
adjustment mode.

Random Access Adjustment Mode

ADJUSTMENT MODE

Select a path from below:

EYE-Q

GUIDED

RANDOM ACCESS

INSTALLATION

SERVICE
Source 1

Select with or

then <ENTER>

<EXIT> to return

Overview Flowchart

RANDOM ACCESS
ADJUSTMENT MODE

SETUP PATTERN
SELECTION

PICTURE TUNING

GEOMETRY

COLOR BALANCE
SYNC
PEAKING
CLAMP TUNING

H PHASE
RASTER SHIFT
LEFT-RIGHT (E-W)

LEFT SIDE CORRECTIONS

SIZE

VER LINEARITY

BLANKING

V CENTERLINE BOW
V CENTERLINE SKEW
SIDE BOW
SIDE KEYSTONE
SEAGULL CORRECTION

LEFT BOW

LEFT KEYSTONE

H CENTERLINE BOW
H CENTERLINE SKEW
TOP KEYSTONE
TOP BOW
BOTTOM KEYSTONE
SEAGULL CORRECTION

RIGHT

LEFT

BOTTOM

TOP

TOP-BOTTOM (N-S)

next page

32

previous page

RANDOM ACCESS
ADJUSTMENT MODE

SETUP PATTERN
SELECTION

COLOR SELECT

FOCUSING

RED
GREEN
BLUE
RED AND GREEN
BLUE AND GREEN
RED AND BLUE

GREEN ONLY
RED ON GREEN
BLUE ON GREEN

RED
GREEN
BLUE

CONVERGENCE

Set up of the Selected Setup Pattern

If an external source is connected to the projector, menu 1 will be displayed.
To select the desired setup pattern, perform the following:
1 Push the cursor keys or to highlight the desired setup pattern
2 Press ENTER to select.

Selecting Setup Pattern

Choose a setup pattern from below:

SELECTED SOURCE

GENLOCKED PATTERN

INTERNAL # PATTERN

Source 01

Select with or

then <ENTER>

<EXIT> to return

menu 1

Genlocked pattern: internally generated cross hatch pattern, locked on the scan rate of external source.
Internal # pattern: internally generated cross hatch pattern and locked on internal generated sync signals. (No

external source necessary)
If no external source is connected to the projector, the internal cross hatch pattern menu will be displayed.
Note: The menus in this manual are created for an external source, connected to one of the inputs, and the

'Genlocked Pattern' is selected.

33

When Using The Internal Cross Hatch Pattern

The Internal # pattern menu will be displayed if the internal cross hatch pattern has been selected or if no
source is connected to the projector.

F

actory Preset Frequencies

The table below lists the 14 fixed factory preset frequencies available.
Another 8 blocks are custom programmable.

To select a desired cross hatch frequency, perform the following:
1 Push the cursor keys or to highlight the desired cross hatch frequency (menu 1).
2 Push the cursor keys or to scroll to another page.
3 Press ENTER if the desired block is selected.

kHz/Hz

31.2/50 EDTV

31.5/60 IDTV (Line Doubled)

31.2/50 HDTV EUREKA

31.5/60 HDTV A TV

33.7/60 HDTV HIVISION (1080i/540p)

15.8/60 EGA 1

21.8/60 EGA 2

61.0/76 VGA 1,2

35.5/87 VGA 4

44.2/70 Super VGA 2

48.5/60 Super VGA 1

61.0/76 Super VGA 3

72.1/67 Super VGA 4

89.3/67 SUN 3/260

Internal Cross Hatch Pattern

INTERNAL # PATTERN

kHz/Hz

15.6/50 PAL/SECAM

15.7/60 NTSC

31.2/50 EDTV

31.5/60 IDTV

31.2/50 HDTV EUREKA

31.5/60 HDTV ATV

Select with or

then <ENTER>

<EXIT> to return

menu 1

What is possible?

This is the main menu for the Random Access adjustment mode.
Through this menu, the following adjustments and features are accessible:

- Picture Tuning

Sync slow/fast(only for RGB inputs)
Color Balance
Peaking
Clamp Tuning

- Geometry

- Convergence

- Focusing

- Color select

Random Access Adjustment Mode Selection Menu

RANDOM ACCESS

ADJUSTMENT MODE

PICTURE TUNING

GEOMETRY

CONVERGENCE

FOCUSING

COLOR SELECT

Select with or

then <ENTER>

<EXIT> to return

menu 1

Picture Tuning

Start up the Picture Tuning

1 Push the cursor keys or to highlight Picture tuning (menu 1).
2 Press ENTER.

The Picture tuning menu will be displayed.
Depending on the input source, the 'Picture tuning' menu will display different items (menu 2).

- Color Balance

- Sync slow/fast

- Peaking

- Clamp Tuning

RANDOM ACCESS

ADJUSTMENT MODE

PICTURE TUNING

GEOMETRY

CONVERGENCE

FOCUSING

COLOR SELECT

Select with or

then <ENTER>

<EXIT> to return

menu 1

PICTURE TUNING

PICTURE TUNING

COLOR BALANCE

SYNC: FAST

PEAKING

CLAMP TUNING

Select with or

then <ENTER>

<EXIT> to return

menu 2

34

COLOR BALANCE

FIXED COLOR BALANCE

3200 4900 6500 9300

CUSTOM RED & BLUE GAIN

CUSTOM GREEN GAIN

CUSTOM RED & BLUE CUT OFF

CUSTOM GREEN CUT OFF

Select with arrow keys

the <ENTER>

Red & Blue:

adjust Red with or

Blue with or

<EXIT> to return

35

Color Balance

What can be done?

The Color Balance function is used to select or adjust the color temperature of white used by the projector.
The Color Balance can be adjusted on two different ways :

- fixed color balance. You have the choice between 3200 K (reddish), 4900 K, 6500 K (white) or 9300 K
(bluish).

- Custom white and black balance.

Ho

w to select the Color Balance?

1 Push the cursor keys or to highlight 'Color Balance' (menu 1).
2 Press ENTER to select.

The color balance menu will be displayed (menu 2).

PICTURE TUNING

PICTURE TUNING
COLOR BALANCE

SYNC: FAST

PEAKING

CLAMP TUNING

Select with or

then <ENTER>

<EXIT> to return

menu 1

menu 2

Fixed Color Balance

To select a fixed color balance, perform the following:

1. Highlight one of the 4 preprogrammed color temperatures with the cursor keys and

2. press ENTER to display the image with the desired color balance.

Custom Color Balance

The custom color balance adjustment can be divided in two parts, the 'gain' adjustment and the 'cut off' adjust­ment.

Gain adjustment (affects the brightest areas of the image)

1. Push the cursor key or to select 'Custom Red & Blue gain' (menu 1).

2. Press ENTER to activate the adjustment.

3. Push the cursor key or to adjust the red gain

4. Push the cursor key or to adjust the blue gain. Abar scale indicates the amount of adjustment.

5. Press ENTER to return to the Color Balance menu.

6. Push the cursor key or to select 'Custom Green Gain' (menu 2).

7. Press ENTER to activate the adjustment.

8. Push the cursor key or to adjust the green gain.

9. Press ENTER to return to the Color Balance menu.

PICTURE TUNING

PICTURE TUNING

COLOR BALANCE

SYNC: FAST

PEAKING

CLAMP TUNING: normal

Select with or

then <ENTER>

<EXIT> to return

36

Cut Off Adjustment

1. Push the cursor key or to select 'Custom Red & Blue Cut off' (menu 3).

2. Press ENTER to activate the adjustment.

3. Push the cursor key or to adjust the red cut-off

4. Push the cursor key or to adjust the blue cut-off.

5. Press ENTER to return to the Color Balance menu.

6. Push the cursor key or to select 'Custom Green cut off' (menu 4).

7. Press ENTER to activate the adjustment.

8. Push the cursor key or to adjust the green cut-off.

9. Press ENTER to return to the Color Balance menu.
When the color balance is adjusted, press EXIT to return.

COLOR BALANCE

FIXED COLOR BALANCE

3200 4900 6500 9300

CUSTOM RED & BLUE GAIN

CUSTOM GREEN GAIN

CUSTOM RED & BLUE CUT OFF

CUSTOM GREEN CUT OFF

Select with arrow keys

the <ENTER>

Red & Blue:

adjust Red with or

Blue with or

<EXIT> to return

menu 1

COLOR BALANCE

FIXED COLOR BALANCE

3200 4900 6500 9300

CUSTOM RED & BLUE GAIN

CUSTOM GREEN GAIN

CUSTOM RED & BLUE CUT OFF

CUSTOM GREEN CUT OFF

Select with arrow keys

the <ENTER>

Red & Blue:

adjust Red with or

Blue with or

<EXIT> to return

menu 2

COLOR BALANCE

FIXED COLOR BALANCE

3200 4900 6500 9300

CUSTOM RED & BLUE GAIN

CUSTOM GREEN GAIN

CUSTOM RED & BLUE CUT OFF

CUSTOM GREEN CUT OFF

Select with arrow keys

the <ENTER>

Red & Blue:

adjust Red with or

Blue with or

<EXIT> to return

menu 3

COLOR BALANCE

FIXED COLOR BALANCE

3200 4900 6500 9300

CUSTOM RED & BLUE GAIN

CUSTOM GREEN GAIN

CUSTOM RED & BLUE CUT OFF

CUSTOM GREEN CUT OFF

Select with arrow keys

the <ENTER>

Red & Blue:

adjust Red with or

Blue with or

<EXIT> to return

menu 4

Sync Fast/Slow Adjustments

What can be done?

The sync function is used to minimize horizontal jittering or tearing at the top to the displayed image.
The sync slow/fast function is only available for RGB sources.

Ho

w to setup the sync function?

To change the Sync setting, perform the following:

1. Push the cursor keys or to select Sync (menu 1)

2. Press ENTER to toggle between FAST and SLOW.
Note: SYNC is normally used in the SLOW position. The FAST position is used to compensate for unsteady sync pulses

from older video playback equipment such as VCRs.

menu 1

PICTURE TUNING

PITURE TUNING

COLOR BALANCE

SYNC: FAST

PEAKING

CLAMP TUNING: normal

Select with or

then <ENTER>

<EXIT> to return

PEAKING

PICTURE TUNING

OFF

LOW FREQUENCY

MID FREQUENCY
HIGH REQUENCY

Select with or

then <ENTER>

<EXIT> to return

PICTURE TUNING

PICTURE TUNING

COLOR BALANCE

SYNC: FAST

PEAKING

CLAMP TUNING: normal

Select with or

then <ENTER>

<EXIT> to return

37

Peaking

What can be done?

Peaking improves the contours in an projected image.

How to set up?

To change the peaking setting, perform the following:

1. Push the cursor key or to select Peaking (menu 1).

2. Press ENTER to display the peaking menu (menu 2).

During the creation of new settings for a RGB source the corresponding peaking is switched on as default.

The following frequency areas are available:

15 kHz - 45 kHz : Low frequency peaking.
45 kHz - 85 kHz : Mid frequency peaking.
85 kHz - 110 kHz : High frequency peaking.

If another peaking is desired or switch off, perform the following:

1. Push the cursor key or to select to select the desired frequency area or off (menu 2).

2. Press ENTER to activate.

Clamp Tuning

menu 1

menu 2

What can be done?

The clamp tuning can be switch between 'Normal' and 'Restoration'.
Normal: for all standard sources and all sources with a backporch > 0.8 µs or for sources with noise and spikes
in the signal.
Restoration: for standard sources with a backporch between 0.4 µs and 0.8 µs or for sources with sync separate
or sync on green.

Ho

w to set up?

1. Push the cursor key or to select Clamp Tuning (menu 1).

2. Press ENTER to toggle between 'Normal' and 'Restoration'.

3. Press EXIT to return to the picture tuning menu.

menu 1

What can be done?

The geometry adjustments have to be done only on the green image. These adjustments are automatically
implemented for the other color images. The following adjustments can be adjusted Left-right (EW) and Top­Bottom Corrections, Blanking, Horizontal Amplitude, Vertical Amplitude, Vertical Linearity and Horizontal Phase.

Star

t Up

To start up the geometry corrections, perform the following:

1. Push the cursor key or to highlight 'Geometry' (menu 1).

2. Press ENTER to select.

The Geometry menu will be displayed on the screen (menu 2).

Impor

tant

The convergence corrections are disabled during geometry corrections. The blanking corrections are only
enabled during the blanking adjustments.

RANDOM ACCESS

ADJUSTMENT MODE

PICTURE TUNING

GEOMETRY

CONVERGENCE

FOCUSING

COLOR SELECT

Select with or

then <ENTER>

<EXIT> to return

38

Geometry Adjustments

Horizontal Phase Adjustments

Start Up

1. Push the cursor key or to highlight 'H Phase' (menu 1).

2. Press ENTER to activate.

The external image with a text box in the middle will be projected.

Note: No horizontal phase adjustment is available on the internal # pattern.

menu 1

GEOMETRY

H PHASE

RASTER SHIFT

LEFT-RIGHT (E-W)

LEFT SIDE CORRECTION

TOP-BOTTOM (N-S)

H SIZE

V LINEARITY

V SIZE

BLANKING

Select with or

then <ENTER>

<EXIT> to return

menu 2

39

How to adjust?

If the raster shift is correctly adjusted, the H Phase text box is projected in the middle of the raster. The "><"
icon indicates the middle of the raster.
Adjust the H Phase control until the middle of the projected image is equal with the middle of >< icon. It is rec­ommended that an external cross-hatch be used for this adjustment.
Image 1 : Push the cursor key to the right to correct.
Image 2 : Push the cursor key to the left to correct.

Note: If the genlocked pattern was selected during the start up of the random access mode, the external source
will be displayed.

A bar scale and a number indicator (between 0 and 100) on the screen give a visual indication of the horizontal
phase adjustment.

GEOMETRY

H PHASE

RASTER SHIFT

LEFT-RIGHT (E-W)

TOP-BOTTOM (N-S)

SIZE

V LINEARITY

BLANKING

Select with or

then <ENTER>

<EXIT> to return

menu 1

Raster Shift Adjustments

What has to be done?

The green raster must be centered both horizontally and vertically on the center of the CRT surface. To center
the green raster, look into the green lens and use the cursor keys to move the raster.

CA

UTION: It is necessary to look into the lenses to perform these adjustments. To avoid eye discom-

fort while looking into the lenses, reduce the contrast and gradually increase the brightness level until
the raster becomes visible on the face of the CRT.

Star

t up

To start the adjustment (image 1):

1. Push the cursor key or to highlight Raster Shift (menu 1).

2. Press ENTER to display the coarse shift menu (menu 2)

3. Select first green horizontal and adjust.

4. Continue with green vertical.

5. Shift red and blue on green.

Note:

Horizontal and Vertical shifts for Red and Blue should end up with a setting close to 50%. If these set-

tings are significantly greater or lesser than 50%, contact a Runco authorized service technician.

W

arning: In order to ensure maximum CRT longevity and to avoid CRT damage, do not shift the raster outside

the phosphor area of the CRT.

image 1

image 2

><

H PHASE

70

><

H PHASE

70

40

GEOMETRY

H PHASE

RASTER SHIFT

LEFT-RIGHT (E-W)

LEFT SIDE CORRECTION

TOP-BOTTOM (N-S)

H SIZE

V LINEARITY

V SIZE

BLANKING

Select with or

then <ENTER>

<EXIT> to return

menu 1

COARSE SHIFT

GREEN HORIZONTAL

GREEN VERTICAL

RED VERTICAL

BLUE VERTICAL

Select with or

then <ENTER>

<EXIT> to return

menu 2

image 1

Forbidden Area

Projected Raster

CRT Faceplate
Border

Phosphor
Border

Left-Right (East-West) Adjustments

What can be adjusted?

Left-right and center adjustments affect only the vertical lines of the projected image. The skew, the bow, the
keystone and the seagull distortion can be adjusted.

Star

t up

To start up the left-right and center adjustments, follow the next procedure :

1. Push the cursor key or to highlight LEFT-RIGHT (E/W) (image 1).

2. Press ENTER to select. The 'Left-Right' menu will be displayed (menu 2).

Note: Only the green image is displayed while making left-right adjustments. The red and blue images will auto­matically be corrected in the same manner. Convergence corrections are automatically disabled for the duration
of these adjustments.

W

hich adjustment can be executed?

The following adjustments can be executed

- vertical centerline bow

- vertical centerline skew

- side keystone (left - right)

- side bow (left - right)

All adjustment are indicated on the screen with the function name, a bar scale and a number between 0 and

100. Adjust the next alignments until the vertical lines are straight.

GEOMETRY

H PHASE

RASTER SHIFT

LEFT-RIGHT (E-W)

LEFT SIDE CORRECTION

TOP-BOTTOM (N-S)

H SIZE

V LINEARITY

V SIZE

BLANKING

Select with or

then <ENTER>

<EXIT> to return

menu 1

LEFT-RIGHT (E-W)

V CENTERLINE BOW

V CENTERLINE SKEW

SIDE BOW

SIDE KEYSTONE

SEAGULL CORRECTION

Warning : Use this correction to adjust

the right side of the image !

Select with or

then <ENTER>

<EXIT> to return

menu 2

41

How to enter an alignment?

To enter an alignment:

1. Push the cursor key or to highlight a function

2. Press ENTER to activate this function.

3. Press EXIT to return.

LEFT-RIGHT

V CENTERLINE BOW

V CENTERLINE SKEW

SIDE BOW

SIDE KEYSTONE

SEAGULL CORRECTION

Select with or

then <ENTER>

<EXIT> to return

menu 2

Warning

Use this correction to adjust the right side of the image.

Correct by pushing the
cursor keys to the right.

Correct by pushing the
cursor keys to the left.

Corrects for curvature of the vertical lines

in the middle of the image.

Corrects for tilting of the vertical lines

in the middle of the image.

Corrects for curvature of the

vertical lines on the right side.

Corrects for keystone geometry of the

vertical lines on the right side.

42

Seagull Correction

What can be done?

Use this correction only if, after adjusting the vertical lines with the side bow or side keystone, an 'S' curve
is visible on the left and the right side of the image. The default value on the bar scale for this correction is 50.

Start up

To correct the Seagull Correction :

1. Push the cursor key or to highlight SEAGULL CORRECTION (menu 1)

2. Press ENTER to activate.

Eliminate the deformation by pushing the cursor key or until a straight line is obtained (image 1).

LEFT-RIGHT (E-W)

V CENTERLINE BOW

V CENTERLINE SKEW

RIGHT BOW

RIGHT KEYSTONE

LEFT BOW

LEFT KEYSTONE

SEAGULL CORRECTION

Select with or

then <ENTER>

<EXIT> to return

menu 2

image 1

Left Side Correction

What can be done?

Fine tuning on the left side of the image for bow and keystone correction. Only the green image is displayed
while making the left side adjustments. The red and blue images will automatically be corrected in the same
manner. The convergence corrections are automatically disabled for the duration of these adjustments.

W

arning

Before starting the left side correction, insure that the side bow and keystone adjustments are done prior to
these fine adjustments!

Start Up

1. Push the cursor key or to highlight 'Left Side Correction' (menu 1).

2. Press ENTER to display the Left Side Correction menu (menu 2).

GEOMETRY

H PHASE

RASTER SHIFT

LEFT-RIGHT (E-W)

LEFT SIDE CORRECTION

TOP-BOTTOM (N-S)

H SIZE

V LINEARITY

V SIZE

BLANKING

Select with or

then <ENTER>

<EXIT> to return

menu 1

LEFT SIDE CORRECTION

LEFT KEYSTONE

LEFT BOW

Ensure that the side bow and key-

stone adjustments are done prior to

these fine adjustments!

Select with or

then <ENTER>

<EXIT> to return

GEOMETRY

H PHASE

RASTER SHIFT

LEFT-RIGHT (E-W)

LEFT SIDE CORRECTION

TOP-BOTTOM (N-S)

H SIZE

V LINEARITY

V SIZE

BLANKING

Select with or

then <ENTER>

<EXIT> to return

43

Left Side Adjustments

1. Push the cursor key or to highlight the desired correction (menu 1).

2. Press ENTER to start the adjustment.

3. Press EXIT to return when the adjustment is finished.

LEFT SIDE CORRECTION

LEFT KEYSTONE

LEFT BOW

Ensure that the side bow and key-

stone adjustments are done prior to

these fine adjustments!

Select with or

then <ENTER>

<EXIT> to return

Top-Bottom (North-South) Adjustments

What can be adjusted?

Top-Bottom and center adjustments affect only the horizontal lines of the projected image. The skew, the bow,
the keystone and the seagull correction can be adjusted.

Star

t Up

To start up the Top-Bottom and center corrections, follow the next procedure :

1. Push the cursor key or to highlight TOP-BOTTOM (N/S) (menu 1).

2. Press ENTER to select. The Top-Bottom menu will be selected (menu 2).

menu 1

TOP-BOTTOM (N-S)

H CENTERLINE BOW

H CENTERLINE SKEW

TOP KEYSTONE

TOP BOW

BOTTOM KEYSTONE

BOTTOM BOW

SEAGULL CORRECTION

Select with or

then <ENTER>

<EXIT> to return

menu 2

Correct by pushing the
cursor keys to the right

Correct by pushing the
cursor keys to the right

Corrects the bow geometry

distortion of the vertical lines.

Corrects the keystone geometry

distortion of the vertical lines.

44

Note:

Only the green image is displayed while making top­botton adjustments. The red and blue images will auto­matically be corrected in the same manner.
Convergence corrections are automatically disabled for
the duration of these adjustments.

W

hich adjustment can be executed?

The following adjustments can be executed

- Horizontal centerline bow

- Horizontal centerline skew

- Top bow

- Top keystone

- Bottom bow

- Bottom keystone

TOP-BOTTOM

H CENTERLINE BOW

H CENTERLINE SKEW

TOP BOW

TOP KEYSTONE

BOTTOM BOW

BOTTOM KEYSTONE

Select with or

then <ENTER>

<EXIT> to return

All adjustments are indicated on the screen with
the function name, a bar scale and a number
between 0 and 100. Adjust the next alignments
until the horizontal lines are straight.

Ho

w to enter an alignment?

To enter an alignment:

1. Push the cursor key or to highlight
a function

2. Press ENTER to activate this function.

3. Press EXIT to return.

Correct by pushing
the cursor key down

Correct by pushing
the cursor key up

Corrects for curvature of the vertical lines

in the middle of the image.

Corrects for tilting of the horizontal lines

in the middle of the image.

Corrects for curvature of the

horizontal lines on the upper side.

Corrects the keystone geometry correction

of the horizontal lines on the upper side.

Connects for curvature of the

horizontal lines on the lower side

Corrects the keystone geometry correction

of the horizontal lines on the lower side.

GEOMETRY

H PHASE

RASTER SHIFT

LEFT-RIGHT (E-W)

LEFT SIDE CORRECTION

TOP-BOTTOM (N-S)

H SIZE

V LINEARITY

V SIZE

BLANKING

Select with or

then <ENTER>

<EXIT> to return

45

Seagull correction

What can be done?

Use this correction after the image has been adjusted with top and bottom bow and keystone. If an “S” curve
on top and bottom of the image is visible, proceed to the seagull correction. Due to interaction, it is possible
that the top and bottom bow have to be readjusted after adjusting the seagull correction to obtain an improved
image. The default value on the bar scale of this correction is 50.

Start up

To correct the Seagull Correction :

1. Push the cursor key or to highlight SEAGULL CORRECTION (menu 1)

2. Press ENTER to activate.
Eliminate the deformation by pushing the cursor key or until a straight line is obtained (image 1).

TOP-BOTTOM (N-S)

H CENTERLINE BOW

H CENTERLINE SKEW

TOP KEYSTONE

TOP BOW

BOTTOM KEYSTONE

BOTTOM BOW

SEAGULL CORRECTION

Select with or

then <ENTER>

<EXIT> to return

menu 2

image 1

Horizontal Size Adjustments

What can be done?

To adjust the horizontal picture size.

Start up

1. Push the cursor key or to highlight 'H Size' (menu 1).

2. Press ENTER to activate (menu 2).

3. Push the cursor key or until the exact image width is obtained (horizontal size) (image 1).

Note:

- If the internal # pattern was selected, this pattern remains on the screen.

- If the genlocked pattern was selected, the external source will be displayed.

A bar scale and a numeric indicator help to gauge the size adjustment.

menu 1

menu 2

H SIZE

70

GEOMETRY

H PHASE

RASTER SHIFT

LEFT-RIGHT (E-W)

LEFT SIDE CORRECTION

TOP-BOTTOM (N-S)

H SIZE

V LINEARITY

V SIZE

BLANKING

Select with or

then <ENTER>

<EXIT> to return

46

Vertical Linearity Adjustments

What can be done?

The vertical linearity adjustment function corrects for vertical non-linearities which extend from the center of the
image to the top and bottom of the image.

Star

t Up

To start up the vertical linearity adjustment:

1. Push the cursor key or to highlight V Linearity (menu 1).

2. Press ENTER to activate (menu 2).

Adjust the vertical linearity with the cursor keys until the distances between the horizontal lines of the set up

pattern are equal from top to bottom (image 1).

menu 1

V LINEARITY

70

menu 2

image 1

GEOMETRY

H PHASE

RASTER SHIFT

LEFT-RIGHT (E-W)

LEFT SIDE CORRECTION

TOP-BOTTOM (N-S)

H SIZE

V LINEARITY

V SIZE

BLANKING

Select with or

then <ENTER>

<EXIT> to return

GEOMETRY

H PHASE

RASTER SHIFT

LEFT-RIGHT (E-W)

LEFT SIDE CORRECTION

TOP-BOTTOM (N-S)

H SIZE

V LINEARITY

V SIZE

BLANKING

Select with or

then <ENTER>

<EXIT> to return

47

What can be done?

To adjust the vertical picture size.

Star

t up

1. Push the cursor key or to highlight 'V Size' (menu 1).

2. Press ENTER to activate (menu 2).

3. Push the cursor key or until the correct image height is obtained. (image 1).

Note:

- If the internal # pattern was selected, this pattern remains on the screen.

- If the genlocked pattern was selected, the external source will be displayed.

A bar scale and a numeric indicator help to gauge the size adjustment.

Vertical Size Adjustments

menu 1

Blanking Adjustments

What can be done?

Blanking adjustments affect only the edges of the projected image and are used to frame the projected image on
to the screen and to hide or black out unwanted information (or noise). A0% on the bar scale indicates no
blanking. The following blanking adjustment are available: Top, Bottom, left and right blanking.

Star

t Up

To start up the Blanking adjustments, follow the next procedure :

1. Push the cursor key or to highlight Blanking (menu 1).

2. Press ENTER to display the blanking menu (menu 2).

- If the internal # pattern was selected, this pattern remains on the screen.

- If the genlocked pattern was selected, the external source will be displayed.

menu 1

BLANKING

TOP

BOTTOM

LEFT

RIGHT

Select with or

then <ENTER>

<EXIT> to return

menu 2

48

How to adjust the Blanking?

Adjust the next blanking alignments until the image is correctly framed or the unwanted information is blanked
out (image 1).
To enter a blanking alignment :

1. Push the cursor key or to highlight the desired blanking position.

2. Press ENTER to select.

3. Press the cursor key or to adjust the blanking.

4. Press ENTER to continue.

Top Blanking

Right Blanking

Bottom Blanking

Left Blanking

BLANKING

TOP

BOTTOM

LEFT

RIGHT

Select with or

then <ENTER>

<EXIT> to return

Correct by pushing the cursor keys
to the right or to the left

Correct by pushing the cursor keys
up or down

Adjustment of the blanking on the of the image

Adjustment of the blanking on the bottom of the image

Adjustment of the blanking on the left side

Adjustment of the blanking on the right side

RANDOM ACCESS

ADJUSTMENT MODE

PICTURE TUNING

GEOMETRY

CONVERGENCE

FOCUSING

COLOR SELECT

Select with or

then <ENTER>

<EXIT> to return

49

Convergence Adjustments

What has to be done?

Convergence adjustments affect both the horizontal and vertical lines of the setup pattern. These adjustments
are performed on the red image while superimposed on the green image and then on the blue image while
superimposed on the green image. The screen is devided into 81 areas

Star

t up

1. Push the cursor key or to select desired adjustment.

2. Press ENTER to activate.

Ho

w to adjust?

1. Use the cursor keys to move the box to the desired zone.

2. Press ENTER to begin the convergence adjustment. Start the convergence adjustment in the center, then
move outward.

3. Use the cursor keys to make horizontal or vertical convergence adjustments in the selected zone (image 1).

4. Press ENTER to move to another zone.

5. Press EXIT to return to the convergence menu.

menu 1

CONVERGENCE

GREEN ONLY

RED ON GREEN

BLUE ON GREEN

Select with or

then <ENTER>

<EXIT> to return

menu 2

menu 3

CONVERGE

ADJUSTMENT

70

image 1

CONVERGENCE

SEL : select area using arrow keys
ADJ : adjust area using arrow keys

Toggle between

SEL and ADJ

with <ENTER>

<ENTER> continue

<EXIT> to return

image 2

Green Image

Red Image

RANDOM ACCESS

ADJUSTMENT MODE

PICTURE TUNING

GEOMETRY

CONVERGENCE

FOCUSING

COLOR SELECT

Select with or

then <ENTER>

<EXIT> to return

50

Focusing

What can be done?

After the lenses are mechanically correct focused, the CRT's can be electronically focused until the image is on
each point.

Star

t Up

1. Push the cursor key or to highlight 'Focusing' (menu 1).

2. Press ENTER to display the focusing menu (menu 2).
The focusing has to be done for the three colors separately.
Start with Green and continue with Red and Blue.
The following items can be adjusted per color (menu 3):

- Midpoint focusing

- Top image focusing

- Bottom image focusing

- Left image focusing

- Right image focusing

menu 1

FOCUSING

RED

GREEN

BLUE

BLUE ON SOURCE

Select with or

then <ENTER>

<EXIT> to return

menu 2

FOCUSING

MIDPOINT

TOP

BOTTOM

LEFT

RIGHT

Select with or

then <ENTER>

<EXIT> to return

menu 3

Midpoint Focusing

1. Push the cursor key or to highlight 'Midpoint' (menu 1).

2. Press ENTER to start up the midpoint focusing.

3. Push the cursor key or until the center of the image is sharp.

4. Press ENTER to return to the focusing menu.

FOCUSING

MIDPOINT

TOP

BOTTOM

LEFT

RIGHT

Select with or

then <ENTER>

<EXIT> to return

menu 1

51

Top Image Focusing

1. Push the cursor key or to highlight 'Top' (menu 1).

2. Press ENTER to start up the top image focusing.

3. Push the cursor key or until the upper part of the image is sharp.

4. Press ENTER to return to the focusing menu.

FOCUSING

MIDPOINT

TOP

BOTTOM

LEFT

RIGHT

Select with or

then <ENTER>

<EXIT> to return

menu 1

Bottom Image Focusing

1. Push the cursor key or to highlight 'Bottom' (menu 1).

2. Press ENTER to start up the bottom image focusing.

3. Push the cursor key or until the lower part of the image is sharp.

4. Press ENTER to return to the focusing menu.

FOCUSING

MIDPOINT

TOP

BOTTOM

LEFT

RIGHT

Select with or

then <ENTER>

<EXIT> to return

menu 1

Left Image Focusing

1. Push the cursor key or to highlight 'Left' (menu 1).

2. Press ENTER to start up the top image focusing.

3. Push the cursor key or until the left part of the image is sharp.

4. Press ENTER to return to the focusing menu.

FOCUSING

MIDPOINT

TOP

BOTTOM

LEFT

RIGHT

Select with or

then <ENTER>

<EXIT> to return

menu 1

RANDOM ACCESS

ADJUSTMENT MODE

PICTURE TUNING

GEOMETRY

CONVERGENCE

FOCUSING

COLOR SELECT

Select with or

then <ENTER>

<EXIT> to return

52

Right Image Focusing

1. Push the cursor key or to highlight 'Right' (menu 1).

2. Press ENTER to start up the right image focusing.

3. Push the cursor key or until the right part of the image is sharp.

4. Press ENTER to return to the focusing menu.

FOCUSING

MIDPOINT

TOP

BOTTOM

LEFT

RIGHT

Select with or

then <ENTER>

<EXIT> to return

menu 1

Blue on Source

What can be done?

After focusing the three colors, and a yellow discoloring on a normal image is
still visible, select blue on source and repeat the steps Midpoint, Top, Bottom,
Left and Right. This helps eliminate blue saturation by slightly

de-focusing the

blue image.

Start Up

1. Push the cursor key or to highlight 'Blue on Source' (menu 1).

2. Press ENTER to start up.
Repeat the midpoint, top, bottom, left and right focusing.

Note: It is recommended that a white field pattern be used for this adjustment.

FOCUSING

RED

GREEN

BLUE

BLUE ON SOURCE

Select with or

then <ENTER>

<EXIT> to return

menu 1

Color Select

What can be done?

Only one color (CRT) or a combination of colors can be turned ON or OFF.

Start Up

1. Push the cursor key or to highlight 'Color Select' (menu 1).

2. Press ENTER to display the color select menu (menu 2).

3. Select the desired color or color combination by pushing the cursor key or .

4. Press ENTER to select.

5. Exit returns to the color select menu.

menu 1

COLOR SELECT

RED

GREEN

BLUE

RED AND GREEN

BLUE AND GREEN

RED AND BLUE

Select with or

then <ENTER>

<EXIT> to return

menu 2

SERVICE MODE

PROJECTOR SET-UP

MEMORY MANAGEMENT

COMMON SETTINGS

I2C DIAGNOSTICS

VOLTAGE DIAGNOSTICS

PROJECTOR DIAGNOSTICS

Select with or

then <ENTER>

<EXIT> to return

53

SERVICE MODE

Start Up

1. Push the cursor key or to select to SERVICE (menu 1).

2. Press ENTER to select.
The service menu will be displayed (menu 2). Some items in the Service mode are password protected
(when the password function is active). Enter your password to continue. All other password protected items
are now also available if you stay in the adjustment mode.

Service Mode

ADJUSTMENT MODE

Select a path from below:

RANDOM ACCESS

INSTALLATION

SERVICE

source 1

Select with or

then <ENTER>

<EXIT> to return

menu 1 menu 2

Ov

erview Flowchart

SERVICE MODE

PROJECTOR SET UP

PROJECTOR DIAGNOSTICS

MEMORY MANAGEMENT

COMMON SETTINGS

VOLTAGE DIAGNOSTICS

I2C DIAGNOSTICS

IDENTIFICATION
TOTAL RUN TIME
CHANGE PASSWORD
CHANGE LANGUAGE
CHANGE PROJECTOR ADDRESS
CHANGE BAUD RATE
PROJECTOR WARM UP
POWER UP MODE
COMMON ADDRESS

COPY A BLOCK
DELETE A BLOCK
DELETE ALL BLOCKS
SET TO MIDPOSITION

DYNAMIC ANTIGMATISM

CRT RUN IN CYCLE

GAMMA CORRECTION

MEMORYBANKS: ON

MENU POSITION: STANDARD

CRT DRIVE MODE

FLYBACK TURNOVER POINT

PROJECTOR SET-UP

IDENTIFICATION

RUN TIME

CHANGE PASSWORD

CHANGE PROJECTOR ADDRESS

CHANGE BAUD RATE

PROJECTOR WARM UP

POWER UP MODE: operating

COMMON ADDRESS: 0

Select with or

then <ENTER>

<EXIT> to return

54

Projector Setup

What can be done?

Within the projector set-up menu, the following items can be consultated or set to the desired setting:

- Identification

- Total run time

- Change password

- Change projector address

- Change baud rate

- Projector warm up

- Power up mode

- Common address

Star

t up the Projector Set-Up

To select Projector Set-Up:

1. Push the cursor key or to highlight Projector Set Up (menu 1).

2. Press ENTER to display the Projector set up menu (menu 2).

SERVICE MODE

PROJECTOR SET-UP

MEMORY MANAGEMENT

COMMON SETTINGS

I2C DIAGNOSTICS

VOLTAGE DIAGNOSTICS

PROJECTOR DIAGNOSTICS

Select with or

then <ENTER>

<EXIT> to return

menu 1

menu 2

Identification

What can be seen?

The 'Identification' screen gives information concerning:

- Projector address. To change the address of your projector, contact a qualified service technician.

- Software version.

- Configuration.

Possible installations:
* Front-ceiling
* Front-table
* Rear-ceiling
* Rear-table

- Baud Rate: transfer speed for communication with an external control system. The baud rate of the projector

must be the same as the baud rate of the connected control system.

- Text ON/OFF

Indicates in operational mode if the bar scale and number indicator will be displayed and if warnings and
failures will be displayed.

ON : displayed
OFF : not displayed

The status can be changed by pressing the 'TEXT' key once on the Remote.

- Serial no.: indicates the fabrication number of the projector. This number can be useful when calling for

technical assistance.

- Projector Level: from 0 to 6. The higher the level the more software options installed. Contact your vendor for

more information.

PROJECTOR SET-UP

IDENTIFICATION

RUN TIME

CHANGE PASSWORD

CHANGE PROJECTOR ADDRESS

CHANGE BAUD RATE

PROJECTOR WARM UP

POWER UP MODE: operating

COMMON ADDRESS: 0

Select with or

then <ENTER>

<EXIT> to return

55

How to start up?

To select Identification:

1. Push the cursor key or to highlight Identification (menu 1).

2. Press ENTER to select. The identification screen will be displayed (menu 2).

PROJECTOR SET-UP

IDENTIFICATION

RUN TIME

CHANGE PASSWORD

CHANGE PROJECTOR ADDRESS

CHANGE BAUD RATE

PROJECTOR WARM UP

POWER UP MODE: operating

COMMON ADDRESS: 0

Select with or

then <ENTER>

<EXIT> to return

menu 1

RUNCO

DTV-1200

Proj. address: 001
Soft. Version: 6.00
Config.: Ceiling/Front
Baud Rate PC: 9600
Text: ON
Serial No.: 103589552
Projector level: 1

menu 2

Run Time

What can be displayed?

The total sytem run time since the first start up can be displayed plus the run time of the separate CRT's since
the last reset.

R

un Time Note:

All projectors leave the factory after a burn-in period of approximately 100 hours.

Ho

w to start up?

To select the different Run Times:

1. Push the cursor key or to highlight 'Run Time (menu 1).

2. Press ENTER to display the run time menu (menu 2).
The amount of time the projector has run since its first start up at the factory will be displayed as the system
run time. The CRT run times will be displayed next to the respective colors.

menu 1

RUN TIME

SYSTEM RUNTIME : 120 h

CRT RUNTIME :

RED : 20 h

GREEN : 20 h

BLUE : 50 h

Select with or

then <ENTER>

<EXIT> to return

menu 2

How to reset the CRT run times?

1. Push the cursor key or to highlight the color of the CRT for which
the Run Time has to be reseted (menu 1).

2. Press ENTER to reset the run time.

3. Press EXIT to return to the Projector Set up menu.

RUN TIME

SYSTEM RUNTIME : 120 h

CRT RUNTIME :

RED : 20 h

GREEN : 20 h

BLUE : 50 h

Select with or

then <ENTER>

<EXIT> to return

menu 2

PROJECTOR SET-UP

IDENTIFICATION

RUN TIME

CHANGE PASSWORD

CHANGE PROJECTOR ADDRESS

CHANGE BAUD RATE

PROJECTOR WARM UP

POWER UP MODE: operating

COMMON ADDRESS: 0

Select with or

then <ENTER>

<EXIT> to return

56

What can be done?

The password code (4 digits) can be changed to a new one.
This item is password protected. First the actual password should be entered before continuing.

Note:

Password function is only active if the jumper on the controller is in the 'ON' position.

Ho

w to select?

To select Change Password :

1. Push the cursor key or to highlight 'Change Password' (menu 1).

2. Press ENTER to display the password menu (menu 2).

If it is the first time you enter a password protected item, enter your password and press ENTER.
The current password is displayed. The new password must consist of 4 digits between 0 and 9.

Ho

w to enter a new password?

Perform the following:

1. Push the cursor key or to select the digits to be changed (menu 2).

2. Press a numeric keys to enter the new digit.

3. Repeat for the other digits.

4. Press ENTER to save the new password.
Before saving the new password, a confirmation screen will be displayed (menu 3).

5. When the displayed password is correct, press ENTER to save.

6. If not correct, press EXIT to cancel the saving.

Change Password

menu 1

PASSWORD

Enter new password :

0 0 0 0

Use and to select,

and reprogram

with numeric keys.

<ENTER> to confirm

<EXIT> to return

menu 2

CHANGE PASSWORD

Password will be

reprogrammed as xxxx

<ENTER> to confirm

<EXIT> to cancel

!

menu 3

PROJECTOR SET-UP

IDENTIFICATION

RUN TIME

CHANGE PASSWORD

CHANGE PROJECTOR ADDRESS

CHANGE BAUD RATE

PROJECTOR WARM UP

POWER UP MODE: operating

COMMON ADDRESS: 0

Select with or

then <ENTER>

<EXIT> to return

PROJECTOR SET-UP

IDENTIFICATION

RUN TIME

CHANGE PASSWORD

CHANGE PROJECTOR ADDRESS

CHANGE BAUD RATE

PROJECTOR WARM UP

POWER UP MODE: operating

COMMON ADDRESS: 0

Select with or

then <ENTER>

<EXIT> to return

Change Projector Address

What can be done?

Every projector requires an individual address between 0 and 255.

Ho

w to change the address?

To change the address, perform the following:

menu 1

PROJECTOR ADDRESS

Enter new projector address:

0 0 0

Use and to select,

and reprogram

with numeric keys.

Highest address is 255

<ENTER> to confirm

<EXIT> to return

menu 2

1. Push the cursor key or to highlight 'Change Projector Address' (menu 1).

2. Press ENTER to select.
The Change Projector Address menu (menu 2) will be displayed and the actual address will be filled in.
The first digit is highlighted.

3. Push the cursor key or to select the digit to be changed.

4. Reprogram with the digit keys on the Remote.

5. Press ENTER to confirm.

Change Baud Rate

What can be set up?

The communication speed between projector and computer has 8 possible speeds.
The baud rate speed can be software set up.
The following baud rates are available: 38400, 19200, 9600, 4800, 2400, 1200.

Ho

w to set up?

To set up the baud rate:

1. Push the cursor key or to highlight 'Change Baud Rate' (menu 1).

2. Press ENTER to select. The actual baud rate will be highlighted (menu 2)

3. Push the cursor key or to select the desired baud rate.

4. Press ENTER to accept.

menu 1

BAUD RATE

Select new baud rate :
38400 19200

9600 4800
2400 1200

Select with arrow keys:

<ENTER> to accept

<EXIT> to return.

menu 2

57

PROJECTOR SET-UP

IDENTIFICATION

RUN TIME

CHANGE PASSWORD

CHANGE PROJECTOR ADDRESS

CHANGE BAUD RATE

PROJECTOR WARM UP

POWER UP MODE: operating

COMMON ADDRESS: 0

Select with or

then <ENTER>

<EXIT> to return

Projector Warm Up

What can be done?

When in the ON position (and the CRT run in cycle is OFF), the projector can start up with a warm up period.
The warm up time can be set up by the customer as well as the frequency of the warm up source. During the
start up a warm up menu will be displayed. This menu offers the option to skip the warm up period by pressing
the EXIT key and offers the possibility to adjust the horizontal and vertical amplitude of this white image with the
cursor keys. During this warm up period, a full white image is shifted on the CRT faceplate to avoid a burn in.

Every 30 seconds a text box will be displayed on another place on the screen with the remaining time to go.
When EXIT is pressed during this warm up period, the warm up menu will be redisplayed with the remaining
time indication. Press another time EXIT to interrupt the warm up cycle. When the warm up option is OFF, when
switching on the projector, it starts immediately with the projection of the selected source.

Ho

w to select?

1. Push the cursor key or to highlight 'Projector Warm up' (menu 1).

2. Press ENTER to select. The projector warm up menu will be displayed (menu 2).

menu 1

PROJECTOR WARM UP

WARM UP : ON

FREQUENCY : 64 kHz

TIME : 15 min

A FULL WHITE PATTERN

WILL BE GENERATED AT

POWER UP

AFTER THIS PROCEDURE

THE PROJECTOR IS READY

TO PERFORM IN OPTIMUM

CONDITION

with <ENTER>

<EXIT> to return

menu 2

Warm Up On/Off

What can be done?

The warm up option can be toggled between ON and OFF.
When in the ON position, while starting up the projector, the warm up cycle will be executed.
When in the OFF position, the projector starts up with inmediate image projection.

Ho

w to turn on the Warm up mode?

1. Push the cursor key or to highlight 'Warm up' (menu 1).

2. Press ENTER to toggle between ON and OFF.

PROJECTOR WARM UP

WARM UP : ON

FREQUENCY : 64 kHz

TIME : 15 min

A FULL WHITE PATTERN

WILL BE GENERATED AT

POWER UP

AFTER THIS PROCEDURE

THE PROJECTOR IS READY

TO PERFORM IN OPTIMUM

CONDITION

with <ENTER>

<EXIT> to return

menu 1

58

PROJECTOR WARM UP

WARM UP : ON

FREQUENCY : 64 kHz

TIME : 15 min

A FULL WHITE PATTERN
WILL BE GENERATED AT

POWER UP

AFTER THIS PROCEDURE

THE PROJECTOR IS READY

TO PERFORM IN OPTIMUM

CONDITION

with <ENTER>

<EXIT> to return

PROJECTOR WARM UP

WARM UP : ON

FREQUENCY : 64 kHz

TIME : 15 min

A FULL WHITE PATTERN
WILL BE GENERATED AT

POWER UP

AFTER THIS PROCEDURE

THE PROJECTOR IS READY

TO PERFORM IN OPTIMUM

CONDITION

with <ENTER>

<EXIT> to return

59

Warm Up Frequency

What can be done?

The line frequency of the white pattern on which the warm up will be executed, can be entered by selecting out
of the displayed list an available block. It is recommended that the Warm up frequency be the same as the input
signal, if possible.

Ho

w to install a warm up frequency ?

1. Push the cursor key or to highlight 'Frequency' (menu 1).

2. Press ENTER to display the projector warm up frequency selection menu (menu 2).

3. Select a block with the cursor keys.

4. Press ENTER to copy the settings of the selected block to the warm up block.

5. Press EXIT to return.

menu 1

PROJECTOR WARM UP

Nr. Src Fh Fv inp conf
1 1 15.6 50 video FC
2 3 31.2 60 RGB3S RT
3 - 15.6 50 intern FC
4 2 31.5 50 RGB3S FC
5 - 33.7 60 intern FC
6

Active block nr. 1

Select block to copy data from with or

<ENTER> to copy settings to warm up block.

<EXIT> to return.

menu 2

Projector Warm Up Time

What can be done?

The warm up time can be programmed with the cursor keys.

Ho

w to program the warm up time?

1. Push the cursor key or to highlight 'Time' (menu 1).

2. Press ENTER to display the projector warm up time menu (menu 2).

3. Use the cursor keys to select the first digit and reprogram with the numeric keys.
Repeat for the other digits.
The projector warm up time is given in minutes.

menu 1

PROJECTOR WARM UP

Enter new time :
15 min

Use and to select

and reprogram

with numeric keys

<ENTER> to confirm

<EXIT> to return

menu 2

PROJECTOR SET-UP

IDENTIFICATION

RUN TIME

CHANGE PASSWORD

CHANGE PROJECTOR ADDRESS

CHANGE BAUD RATE

PROJECTOR WARM UP

POWER UP MODE: operating

COMMON ADDRESS: 0

Select with or

then <ENTER>

<EXIT> to return

PROJECTOR SET-UP

IDENTIFICATION

RUN TIME

CHANGE PASSWORD

CHANGE PROJECTOR ADDRESS

CHANGE BAUD RATE

PROJECTOR WARM UP

POWER UP MODE: operating

COMMON ADDRESS: 0

Select with or

then <ENTER>

<EXIT> to return

60

Power Up Mode

What can be done?

When pressing the power switch, the projector can start up in 'operating mode' or in 'stand-by mode'.
Operating mode: the projector start up and displays image.

Stand-by mode: the projector start up in stand-by and waits until the stand-by button or a digit key is pressed.

Ho

w to change the mode?

To change the Power up mode:

1. Push the cursor key or to highlight Power Up (menu 1).

2. Press ENTER to toggle between 'Operating' and 'Standby'.

menu 1

W

hat can be done?

Every projector listens to a common address. This common address can be set to '0' or '1'. When a Remote is
programmed with a common address, every projector with that same common address will follow up the com­mands given by that Remote.

W

hy 2 different common address?

The reason to have the choice to select between common addresses is, to avoid controlling of other IR con­trolled units, e.g. a TV set with standard common address 0.

Ho

w to change the common address?

1. Push the cursor key or to highlight Common Address (menu 1).

2. Press ENTER to toggle between '0' and '1'.

Common Address

Note: Runco recommends that this be left in
‘Standby’ for long-term reliability.

menu 1

SERVICE MODE

PROJECTOR SET-UP

MEMORY MANAGEMENT

COMMON SETTINGS

I2C DIAGNOSTICS

Select with or

then <ENTER>

<EXIT> to return

61

What can be done?

Within the memory management menu, the following items can be consultated or executed :

- copy a block

- delete a block

- delete all blocks

- set to midposition

Ho

w to select?

To select Memory Management:

1. Push the cursor key or to highlight Memory Management (menu 1).

2. Press ENTER to select. The memory management menu will be displayed (menu 2).

Memory Management

menu 1

MEMORY MANAGEMENT

COPY A BLOCK

DELETE A BLOCK

DELETE ALL BLOCKS

SET TO MIDPOSITION

Select with or

then <ENTER>

<EXIT> to return

menu 2

Copy a Block

What can be done?

The copy a block function copies the settings of a selected block into the active block.

How to copy?

To copy a block :

1. Push the cursor key or o highlight 'Copy a Block' (menu 1).

2. Press ENTER to select.
The copy menu will be displayed (menu 2).
To copy the settings of a closed block to the block you are working on (active block),

3. Push the cursor key or to select a block.

4. Press ENTER to copy the selected block.

All current settings will be overwritten with the settings of the block which is copied.
A confirmation screen will be displayed (menu 3).

5. ENTER to confirm. EXIT cancels the copy procedure and returns without copying the block.

MEMORY MANAGEMENT

COPY A BLOCK

DELETE A BLOCK

DELETE ALL BLOCKS

SET TO MIDPOSITION

Select with or

then <ENTER>

<EXIT> to return

menu 1

CHANGE PASSWORD

Password will be

reprogrammed as xxxx

<ENTER> to confirm

<EXIT> to cancel

!

menu 3

COPY MODE

Nr. Src Fh Fv inp conf
1 1 15.6 50 video FC
2 3 31.2 60 RGB3S RT
3 - 15.6 50 intern FC
4 2 31.5 50 RGB3S FC
5 - 33.7 60 intern FC
6
7
8

Active block nr. 1

Select with or

<ENTER> to copy

<EXIT> to return.

menu 2

MEMORY MANAGEMENT

COPY A BLOCK

DELETE A BLOCK

DELETE ALL BLOCKS

SET TO MIDPOSITION

Select with or

then <ENTER>

<EXIT> to return

What can be done?

The delete function is used to clear all data (settings) from an adjustment block.
A delete can be given:

- block by block or

- for all blocks.

This item is password protected.

What can be done?

The 'delete a block' function deletes the settings of a selected block.

How to delete a Block?

1. Push the cursor key or to highlight Delete a Block (menu 1).

2. Press ENTER to display the delete mode (menu 2).

3. Push the cursor key or to select the desired adjustment block.

4. Press ENTER to delete the selected adjustment block.

A confirmation menu will be displayed (menu 3).

5. Press ENTER to confirm.
Press EXIT to cancel the deletion procedure

Deletion of Blocks

Deleting Block by Block

menu 1

DELETE MODE

Nr. Src Fh Fv inp conf
1 1 15.6 50 video FC
2 3 31.2 60 RGB3S RT
3 - 15.6 50 intern FC
4 2 31.5 50 RGB3S FC
5 - 33.7 60 intern FC
6
7
8

Active block nr. 1

Select with or

<ENTER> to copy

<EXIT> to return.

menu 2

DELETE BLOCK

The selected block

will be deleted!

<ENTER> to confirm

<EXIT> to cancel

!

menu 3

Deletion of All Blocks

What can be done?

All blocks (all settings) can be deleted at the same time.

Ho

w to delete all blocks?

1. Push the cursor key or to highlight Delete all Blocks (menu 1).

2. Press ENTER to select.

A confirmation screen will be displayed (menu 2).

3. Press ENTER to confirm
Press EXIT to return without deleting any block.

Once ENTER is pressed, all block headers and adjustment settings are permanently removed
and cannot be restored.

62

MEMORY MANAGEMENT

COPY A BLOCK

DELETE A BLOCK

DELETE ALL BLOCKS

SET TO MIDPOSITION

Select with or

then <ENTER>

<EXIT> to return

MEMORY MANAGEMENT

COPY A BLOCK

DELETE A BLOCK

DELETE ALL BLOCKS

SET TO MIDPOSITION

Select with or

then <ENTER>

<EXIT> to return

63

Set to Midposition

What can be done?

All adjustment settings (geometry and convergence) can be set to mid position.
Item is password protected.

Ho

w to Start Up?

1. Push the cursor key or to highlight 'Set to Midposition' (menu 1).

2. Press ENTER to display the set to midposition menu (menu 2).

menu 1

DELETE ALL BLOCKS

All blocks

will be deleted!

<ENTER> to confirm

<EXIT> to cancel

!

menu 2

menu 1

SET TO MIDPOSITION

R&B CONVERGENCE MID

GREEN CONVERGENCE MID

FOCUS TO MIDPOSITION

E-W TO MIDPOSITION

N-S TO MIDPOSITION

DIG VERT LINEARITY MID

DIG HOR LINEARITY MID

ASTIGMATISM MIDPOSITION

ALL SETTINGS TO MIDPOS

Select with or

then <ENTER>

<EXIT> to return.

menu 2

R & B Covergence Mid

What can be done?

All convergence settings for red and blue are set to midposition.
Item is password protected

How to set convergence to midposition:

1. Push the cursor key or to highlight 'R & B Convergence Mid' (menu 1).

2. Press ENTER to select. A confirmation screen will be displayed first (menu 2).

3. Press ENTER to confirm.

SET TO MIDPOSITION

R&B CONVERGENCE MID

GREEN CONVERGENCE MID

FOCUS TO MIDPOSITION

E-W TO MIDPOSITION

N-S TO MIDPOSITION

DIG VERT LINEARITY MID

DIG HOR LINEARITY MID

ASTIGMATISM MIDPOSITION

ALL SETTINGS TO MIDPOS

Select with or

then <ENTER>

<EXIT> to return.

SET TO MIDPOSITION

UNDO R&B CONVERGENCE MID

GREEN CONVERGENCE MID

FOCUS TO MIDPOSITION

E-W TO MIDPOSITION

N-S TO MIDPOSITION

DIG VERT LINEARITY MID

DIG HOR LINEARITY MID

ASTIGMATISM MIDPOSITION

ALL SETTINGS TO MIDPOS

Select with or

then <ENTER>

<EXIT> to return.

64

Undo R & B Convergence Mid

What can be done?

When "R & B convergence mid" is selected, all convergence settings are
set to their midposition. With the undo, it is possible to return to the
previous settings as long as the projector is playing on the same source
(= same adjustment block).
'Undo R & B convergence mid' is displayed in the Set Midposition menu
instead of 'R & B convergence mid' when this latter is pressed.

Ho

w to Undo?

1. Push the cursor key or to highlight 'Undo R & B
Convergence Mid' (menu 1).

2. Press ENTER execute the undo function.

menu 1

Green Convergence Mid

What can be done?

The green convergence settings can be set to midposition.
Only available when the projector is equipped with green convergence adjustments.

How to set Green settings to midposition?

1. Push the cursor key or to highlight 'Green Convergence Mid' (menu 1).

2. Press ENTER to select. A confirmation screen will be displayed first (menu 2).

3. Press ENTER to confirm.
Press EXIT to cancel the procedure to set the green convergence settings to their midposition.

menu 1

SET TO MIDPOSITION

R&B CONVERGENCE MID

GREEN CONVERGENCE MID

FOCUS TO MIDPOSITION

E-W TO MIDPOSITION

N-S TO MIDPOSITION

DIG VERT LINEARITY MID

DIG HOR LINEARITY MID

ASTIGMATISM MIDPOSITION

ALL SETTINGS TO MIDPOS

Select with or

then <ENTER>

<EXIT> to return.

menu 1

R & B CONVERGENCE MID

Convergence settings

in current block

will be overwritten!

<ENTER> to confirm

<EXIT> to cancel

!

menu 2

GREEN CONVERGENCE MID

Convergence settings

in current block

will be overwritten!

<ENTER> to confirm

<EXIT> to cancel

!

menu 2

SET TO MIDPOSITION

R&B CONVERGENCE MID

GREEN CONVERGENCE MID

UNDO FOCUS TO MIDPOSITION

E-W TO MIDPOSITION

N-S TO MIDPOSITION

DIG VERT LINEARITY MID

DIG HOR LINEARITY MID

ASTIGMATISM MIDPOSITION

ALL SETTINGS TO MIDPOS

Select with or

then <ENTER>

<EXIT> to return.

SET TO MIDPOSITION

R&B CONVERGENCE MID

GREEN CONVERGENCE MID

FOCUS TO MIDPOSITION

E-W TO MIDPOSITION

N-S TO MIDPOSITION

DIG VERT LINEARITY MID

DIG HOR LINEARITY MID

ASTIGMATISM MIDPOSITION

ALL SETTINGS TO MIDPOS

Select with or

then <ENTER>

<EXIT> to return.

SET TO MIDPOSITION

R&B CONVERGENCE MID

UNDO GREEN CONVERGENCE MID

FOCUS TO MIDPOSITION

E-W TO MIDPOSITION

N-S TO MIDPOSITION

DIG VERT LINEARITY MID

DIG HOR LINEARITY MID

ASTIGMATISM MIDPOSITION

ALL SETTINGS TO MIDPOS

Select with or

then <ENTER>

<EXIT> to return.

65

Undo Green Convergence Mid

What can be done?

'Undo Green convergence mid' is displayed in the Set Midposition menu
instead of 'Green convergence mid' when the latter is pressed. Only available
when the projector is equipped with green convergence adjustmentes.

Ho

w to undo?

1. Push the cursor key or to highlight 'Undo Green Convergence Mid'
(menu 1).

2. Press ENTER undo.

menu 1

Focus to Midposition

What can be done?

The focus settings can be set to midposition.

How to set the Focus settings to midposition?

1. Push the cursor key or to highlight 'Focus to Midposition' (menu 1).

2. Press ENTER to select. A confirmation screen will be displayed first (menu 2).

3. Press ENTER to confirm. Press EXIT to cancel the procedure to set the focus settings to their midposition.

menu 1

FOCUS TO MIDPOSITION

Focus settings

in current block

will be overwritten!

<ENTER> to confirm

<EXIT> to cancel

!

menu 2

Undo Focus to Midposition

What can be done?

'Undo Focus to Midposition' is displayed in the Set Midposition menu instead
of 'Focus to midposition' when the latter is pressed. As long the projector is
running on the same source (= same adjustment block), undo the focus to
midposition is possible.

Ho

w to undo the Focus to midposition?

1. Push the cursor key or to highlight 'Undo Focus to Midposition'
(menu 1).

2. Press ENTER undo.

menu 1

SET TO MIDPOSITION

R&B CONVERGENCE MID

GREEN CONVERGENCE MID

FOCUS TO MIDPOSITION

E-W TO MIDPOSITION

N-S TO MIDPOSITION

DIG VERT LINEARITY MID

DIG HOR LINEARITY MID

ASTIGMATISM MIDPOSITION

ALL SETTINGS TO MIDPOS

Select with or

then <ENTER>

<EXIT> to return.

SET TO MIDPOSITION

R&B CONVERGENCE MID

GREEN CONVERGENCE MID

FOCUS TO MIDPOSITION

UNDO E-W TO MIDPOSITION

N-S TO MIDPOSITION

DIG VERT LINEARITY MID

DIG HOR LINEARITY MID

ASTIGMATISM MIDPOSITION

ALL SETTINGS TO MIDPOS

Select with or

then <ENTER>

<EXIT> to return.

SET TO MIDPOSITION

R&B CONVERGENCE MID

GREEN CONVERGENCE MID

FOCUS TO MIDPOSITION

E-W TO MIDPOSITION

N-S TO MIDPOSITION

DIG VERT LINEARITY MID

DIG HOR LINEARITY MID

ASTIGMATISM MIDPOSITION

ALL SETTINGS TO MIDPOS

Select with or

then <ENTER>

<EXIT> to return.

66

East-West to Midposition

What can be done?

The east-west settings can be set to midposition.

Ho

w to set the E-W settings to midposition?

1. Push the cursor key or to highlight 'E-W to midposition' (menu 1).

2. Press ENTER to select. A confirmation screen will be displayed first (menu 2).

3. Press ENTER to confirm. Press EXIT to cancel the procedure to set the E-W settings to their midposition.

menu 1

E-W TO MIDPOSITION

E-W settings

in current block

will be overwritten!

<ENTER> to confirm

<EXIT> to cancel

!

menu 2

Undo East-West to Midposition

What can be done?

'Undo East-West to midposition' is displayed in the Set Midposition menu
instead of 'E-W to midposition' when this latter is pressed. The settings for
the E-W can be returned to previous installed settings as long the projector
is playing on the same source ( = same adjustment block).

Ho

w to Undo the E-W to midposition?

1. Push the cursor key or to highlight 'Undo E-W to midposition'
(menu 1).

2. Press ENTER undo.

menu 1

North-South Settings to Midposition

What can be done?

The north-south settings can be set to midposition.

Ho

w to set the N-S settings to midposition?

1. Push the cursor key or to highlight 'N-S to midposition' (menu 1).

2. Press ENTER to select. A confirmation screen will be displayed first (menu 2).

3. Press ENTER to confirm. Press EXIT to cancel the procedure to set the N-S settings to their midposition.

menu 1

N-S TO MIDPOSITION

North - South settings

in current block

will be overwritten!

<ENTER> to confirm

<EXIT> to cancel

!

menu 2

SET TO MIDPOSITION

R&B CONVERGENCE MID

GREEN CONVERGENCE MID

FOCUS TO MIDPOSITION

E-W TO MIDPOSITION

N-S TO MIDPOSITION

UNDO DIG VERT LINEARITY MID

DIG HOR LINEARITY MID

ASTIGMATISM MIDPOSITION

ALL SETTINGS TO MIDPOS

Select with or

then <ENTER>

<EXIT> to return.

SET TO MIDPOSITION

R&B CONVERGENCE MID

GREEN CONVERGENCE MID

FOCUS TO MIDPOSITION

E-W TO MIDPOSITION

N-S TO MIDPOSITION

DIG VERT LINEARITY MID

DIG HOR LINEARITY MID

ASTIGMATISM MIDPOSITION

ALL SETTINGS TO MIDPOS

Select with or

then <ENTER>

<EXIT> to return.

SET TO MIDPOSITION

R&B CONVERGENCE MID

GREEN CONVERGENCE MID

FOCUS TO MIDPOSITION

E-W TO MIDPOSITION

UNDO N-S TO MIDPOSITION

DIG VERT LINEARITY MID

DIG HOR LINEARITY MID

ASTIGMATISM MIDPOSITION

ALL SETTINGS TO MIDPOS

Select with or

then <ENTER>

<EXIT> to return.

67

Undo North-South Settings to Midposition

What can be done?

'Undo N-S to midposition' is displayed in the Set Midposition menu instead of
'N-S to midposition' when the latter is pressed. The settings for the N-S can be
returned to previous installed settings as long the projector is playing on the
same source ( = same adjustment block).

Ho

w to Undo the N-S to midposition?

1. Push the cursor key or to highlight 'Undo N-S to midposition' (menu 1).

2. Press ENTER undo.

menu 1

Digital Vertical Linearity to Midposition

What can be done?

The digital vertical linearity settings for the different areas can be set to their midposition.

Ho

w to set the Digital Vertical Linearity to Midposition?

1. Push the cursor key or to highlight 'Dig Vert Linearity mid' (menu 1).

2. Press ENTER to select. A confirmation screen will be displayed first (menu 2).

3. Press ENTER to confirm. Press EXIT to cancel the procedure to set the Digital Vertical Linearity to their mid
position.

menu 1

DIG VERTLINEARITY

TO MIDPOSITION

Dig Vert Linearity settings

in current block

will be overwritten!

<ENTER> to confirm

<EXIT> to cancel

!

menu 2

What can be done?

'Undo digital vertical linearity to midposition' is displayed in the Set Midposition
menu instead of 'Dig Vert Linearity to midposition' when this latter is pressed.
The settings for the dig vert linearity can be returned to previous installed set­tings as long the projector is playing on the same source ( = same adjustment
block).

Ho

w to undo the digital vertical linearity to midposition?

1. Push the cursor key or to highlight 'Undo Dig Vert Linearity to midposi-

tion' (menu 1).

2. Press ENTER undo.

Undo Digital Vertical Linearity to Midposition

menu 1

SET TO MIDPOSITION

R&B CONVERGENCE MID

GREEN CONVERGENCE MID

FOCUS TO MIDPOSITION

E-W TO MIDPOSITION

N-S TO MIDPOSITION

DIG VERT LINEARITY MID

DIG HOR LINEARITY MID

ASTIGMATISM MIDPOSITION

ALL SETTINGS TO MIDPOS

Select with or

then <ENTER>

<EXIT> to return.

SET TO MIDPOSITION

R&B CONVERGENCE MID

GREEN CONVERGENCE MID

FOCUS TO MIDPOSITION

E-W TO MIDPOSITION

N-S TO MIDPOSITION

DIG VERT LINEARITY MID

UNDO DIG HOR LINEARITY MID

ASTIGMATISM MIDPOSITION

ALL SETTINGS TO MIDPOS

Select with or

then <ENTER>

<EXIT> to return.

SET TO MIDPOSITION

R&B CONVERGENCE MID

GREEN CONVERGENCE MID

FOCUS TO MIDPOSITION

E-W TO MIDPOSITION

N-S TO MIDPOSITION

DIG VERT LINEARITY MID

DIG HOR LINEARITY MID

ASTIGMATISM MIDPOSITION

ALL SETTINGS TO MIDPOS

Select with or

then <ENTER>

<EXIT> to return.

68

Digital Horizontal Linearity to Midposition

What can be done?

The digital horizontal linearity settings for the different areas can be set to their midposition.

Ho

w to set the Digital Horizontal Linearity to Midposition?

1. Push the cursor key or to highlight 'Dig Hor Linearity mid' (menu 1).

2. Press ENTER to select. A confirmation screen will be displayed first (menu 2).

3. Press ENTER to confirm. Press EXIT to cancel the procedure to set the Digital horizontal linearity to their

midposition.

menu 1

DIG HOR LINEARITY

TO MIDPOSITION

Dig Hor Linearity settings

in current block

will be overwritten!

<ENTER> to confirm

<EXIT> to cancel

!

menu 2

Undo Digital Horizontal Linearity to Midposition

What can be done?

'Undo digital horizontal linearity to midposition' is displayed in the Set
Midposition menu instead of 'Dig Hor Linearity to midposition' when the latter
is pressed. The settings for the dig hor linearity can be returned to previous
installed settings as long the projector is playing on the same source ( = same
adjustment block).

Ho

w to undo the digital horizontal linearity to midposition?

1. Push the cursor key or to highlight 'Undo Dig Vert Linearity to
midposition' (menu 1).

2. Press ENTER undo.

menu 1

Astigmatism to Midposition

What can be done?

The astigmatism settings for the different areas can be set to their midposition.

Ho

w to set the Astigmatism to Midposition?

1. Push the cursor key or to highlight 'Astigmatism' (menu 1).

2. Press ENTER to select. A confirmation screen will be displayed first (menu 2).

3. Press ENTER to confirm. Press EXIT to cancel the procedure to set the Astigmatism to their midposition.

menu 1

ASTIGMATISM

TO MIDPOSITION

Astigmatism settings

in current block

will be overwritten!

<ENTER> to confirm

<EXIT> to cancel

!

menu 2

SET TO MIDPOSITION

R&B CONVERGENCE MID

GREEN CONVERGENCE MID

FOCUS TO MIDPOSITION

E-W TO MIDPOSITION

N-S TO MIDPOSITION

DIG VERT LINEARITY MID

DIG HOR LINEARITY MID

ASTIGMATISM MIDPOSITION

UNDO ALL SETTINGS TO MIDPOS

Select with or

then <ENTER>

<EXIT> to return.

SET TO MIDPOSITION

R&B CONVERGENCE MID

GREEN CONVERGENCE MID

FOCUS TO MIDPOSITION

E-W TO MIDPOSITION

N-S TO MIDPOSITION

DIG VERT LINEARITY MID

DIG HOR LINEARITY MID

ASTIGMATISM MIDPOSITION

ALL SETTINGS TO MIDPOS

Select with or

then <ENTER>

<EXIT> to return.

69

Undo Astigmatism to Midposition

What can be done?

'Undo Astigmatism midposition' is displayed in the Set Midposition menu
instead of 'Astigmatism midposition' when the latter is pressed. The settings
for the astigmatism can be returned to previous installed settings as long the
projector is playing on the same source ( = same adjustment block).

Ho

w to undo the Astigmatism settings to midposition?

1. Push the cursor key or to highlight 'Undo Astigmatism Midposition'
(menu 1).

2. Press ENTER undo.

menu 1

SET TO MIDPOSITION

R&B CONVERGENCE MID

GREEN CONVERGENCE MID

FOCUS TO MIDPOSITION

E-W TO MIDPOSITION

N-S TO MIDPOSITION

DIG VERT LINEARITY MID

DIG HOR LINEARITY MID

UNDO ASTIGMATISM MIDPOSITION

ALL SETTINGS TO MIDPOS

Select with or

then <ENTER>

<EXIT> to return.

All Settings to Midposition

What can be done?

All adjustment settings can be set to midposition.

Ho

w to set to midposition?

1. Push the cursor key or to highlight 'All Settings to Midposition' (menu 1).

2. Press ENTER to select. A confirmation menu will be displayed first (menu 2).

3. Press ENTER to confirm. Press EXIT to cancel the operation 'set all settings to their midposition'.

menu 1

ALL SETTINGS

TO MIDPOSITION

Astigmatism settings

in current block

will be overwritten!

<ENTER> to confirm

<EXIT> to cancel

!

menu 2

Undo All Settings to Midposition

menu 1

W

hat can be done?

'Undo all settings to Midposition' is displayed in the Memory management
menu instead of 'All settings to midposition' when the latter is pressed.

An undo is possible as long as the projector is running on the same source (=
same adjustment block) even when some adjustments as geometry or conver­gence are already readjusted. When undo is pressed all settings are reset to
the previous settings.

Ho

w to cancel 'Set to midposition'?

When "All settings to midpos" is selected, all settings are set to their
midposition. To cancel this action:

1. Push the cursor key or to highlight 'Undo All Settings to midpos'
(menu 1).

2. Press ENTER to cancel the set to midposition action.
Press EXIT to cancel the procedure 'undo set to midposition'.

SERVICE MODE

PROJECTOR SET-UP

MEMORY MANAGEMENT

COMMON SETTINGS

I2C DIAGNOSTICS

VOLTAGE DIAGNOSTICS

PROJECTOR DIAGNOSTICS

Select with or

then <ENTER>

<EXIT> to return

70

Common Settings

What can be done?

Within the common settings menu, the following items can be set up or executed:

- Dynamic Astigmatism

- Gamma Correction

- CRT run in cycle

- CRT Drive mode

- Memory banks : on/off

- Flyback turnover point

- Menu Position : standard/middle

Ho

w to select?

1. Push the cursor key or to highlight 'Common Settings' (menu 1).

2. Press ENTER to select. The common settings menu will be displayed (menu 2)

menu 1

COMMON SETTINGS

DYNAMIC ASTIGMATISM

GAMMA CORRECTIONS

CRT RUN IN CYCLE

CRT DRIVE MODE

MEMORYBANKS : ON

FLYBACK TURNOVER POINT

MENU POSITION : STANDARD

Select with or

then <ENTER>

<EXIT> to return

menu 2

Dynamic Astigmatism

What can be done?

The spot shape adjustments correct the spot shape in 25 different areas on the screen for the three colors
separately. The spot shape is adjusted according to the axial axises and the diagonal axises when using the
cursor keys on the Remote. These adjustments have to be done on a dot pattern (external source or genlocked
pattern).

Spot shapes

before dynamic

astigmatism correction

Diagonal

astigmatism correction

(use the and

arrow key)

Axial

astigmatism correction

(use the and

arrow key)

Spot shapes

after dynamic

astigmatism correction

71

Start Up

To start up the dynamic astigmatism:

1. Push the cursor key or to highlight 'Dynamic Astigmatism' (menu 1).

2. Press ENTER to display the dynamic astigmatism menu (menu 2). The dynamic astigmatism can be adjusted

on the selected source or on pattern lock on the selected source (genlocked pattern). The way of adjusting is
the same for both ways and for each color. The explanation will only be given for one color.

COMMON SETTINGS

DYNAMIC ASTIGMATISM

GAMMA CORRECTIONS

CRT RUN IN CYCLE

CRT DRIVE MODE

MEMORYBANKS : ON

FLYBACK TURNOVER POINT

MENU POSITION : STANDARD

Select with or

then <ENTER>

<EXIT> to return

menu 1

DYNAMIC ASTIGMATISM

ON SELECTED SOURCE

RED

GREEN

BLUE

ON GENLOCKED PATTERN

RED

GREEN

BLUE

FOCUSING ON CURRENT SOURCE

Select with or

then <ENTER>

<EXIT> to return

menu 1

Ho

w to adjust?

The adjustment of the dynamic astigmatism is done on the selected source or genlocked pattern and for each
color separately. The menu will be displayed hereafter for a genlocked pattern on the green image.

To adjust, follow the next procedure:

1. Push the cursor key or to highlight 'green’ under Genlocked Pattern (menu 1).

2. Press ENTER to display the dynamic astigmatism adjustment menu (menu 2).
The screen is divided into 25 areas (5 x 5) (menu 3). In each area, the spot shape can be adjusted.

3. Use the cursor keys to select the desired area.

4. Increase the contrast level using the Contrast Control to near maximum. Using the "+" Sharpness Key,
defocus the image until the dots are large and easily visible.

DYNAMIC ASTIGMATISM

ON SELECTED SOURCE

RED

GREEN

BLUE

ON GENLOCKED PATTERN

RED

GREEN

BLUE

FOCUSING ON CURRENT SOURCE

Select with or

then <ENTER>

<EXIT> to return

menu 1

DYNAMIC ASTIGMATISM

SEL : select area using arrow keys
ADJ : adjust axial astig. using or ,
diagonal astig. using or .

Toggle between SEL and ADJ with <EXIT>
Toggle between 4-POLE and 6-POLE with
<ENTER>
Use the <SHARPNESS> keys for the defo­cusing of the image.

<ENTER> to continue
<EXIT> to return

menu 2

5. Press EXIT to toggle the cursor keys from selection keys to adjustment keys.

6. Adjust first the 4 pole correction. Adjust the spot shape in the axial or diagonal direction, using the cursor

keys. Adjust until the spot shape is circular. Use the cursor key or for the diagonal astigmatism adjust
ment and the cursor key or for the axial astigmatism adjustment.

7. Press ENTER to toggle from the 4 pole correction to the 6 pole correction or vice versa.

8. Adjust the spot shape again using the cursor keys.

9. Press EXIT to return to the area selection screen.

10. Repeat from step 3 as may times as necessary.

COMMON SETTINGS

DYNAMIC ASTIGMATISM
GAMMA CORRECTIONS

CRT RUN IN CYCLE

CRT DRIVE MODE

MEMORYBANKS : ON

FLYBACK TURNOVER POINT

MENU POSITION : STANDARD

Select with or

then <ENTER>

<EXIT> to return

COMMON SETTINGS

DYNAMIC ASTIGMATISM

GAMMA CORRECTIONS

CRT RUN IN CYCLE

CRT DRIVE MODE

MEMORYBANKS : ON

FLYBACK TURNOVER POINT

MENU POSITION : STANDARD

Select with or

then <ENTER>

<EXIT> to return

72

Start Up

To start up the gamma corrections :

1. Push the cursor key or to highlight 'Gamma Corrections' (menu 1).

2. Press ENTER to start up. A warning screen will be displayed (menu 2).

Gamma Corrections

menu 1

WARNING

RISK OF INCORRECT ADJUSTMENT

OF THE PROJECTOR

THE GAMMA CORRECTIONS ARE
FACTORY ADJUSTED USING COLOUR
ANALYSER! THEREFORE, ONLY
QUALIFIED INSTALLATION OR SERVICE
PERSONNEL SHOULD PERFORM
THESE ADJUSTMENTS !

<ENTER> TO CONTINUE
<EXIT> TO RETURN

menu 2

CRT Run In Cycle

What can be done?

Only necessary when a new picture tube is installed or when CRT arcing continues. The CRT run in cycle
option can only be activated when memory blocks on an internal # pattern are available. When one or more
such blocks are available, a flashing white image (5 sec on, 5 sec off) is generated and then for 5 min on the
first internal block. In the next 5 min, a second internal block will be used to generate the flashing white image.
The image will also be shifted in a vertical way to prevent a CRT burn in. To quit the CRT run in cycle option,
press EXIT.

Ho

w to select CRT run in cycle?

1. Push the cursor key or to highlight 'CRT run in Cycle' (menu 1).

2. Press ENTER to start up. If a memory block adjusted on an internal # pattern is available, the CRT run in
cycle will start. If no such a block is available, the projector cannot run the CRT run in option and leaves the
adjustment mode. If you still want to run CRT run in cycle, create first a memory block on an internal #
pattern and restart the CRT run in option.

menu 1

CRT RUN IN CYCLE

A flashing white pattern will be

generated until <EXIT> is pressed.

The projector only uses memory

blocks adjusted on an internal

# pattern; if no such block is

available, the projector can't run

the procedure and leaves the

adjusment mode.

<ENTER> to continue

<EXIT> to cancel

menu 2

COMMON SETTINGS

DYNAMIC ASTIGMATISM
GAMMA CORRECTIONS

CRT RUN IN CYCLE

CRT DRIVE MODE

MEMORYBANKS : ON

FLYBACK TURNOVER POINT

MENU POSITION : STANDARD

Select with or

then <ENTER>

<EXIT> to return

73

What can be done?

The projector CRT's can be driven with the normal current (normal mode), a lower current (economic mode) or
with a higher current (boost mode). The higher the current, the higher the light output but the lifetime will
shorten.

A

vailable drive modes

- Normal

- Economic: Lower drive current to the CRT's, the lifetime of the CRT's will enlarge but the light output will

reduce.

- Tempory boost: Higher drive current to the CRT's, the lifetime of the CRT's will shorten but the light output will

be higher. This situation is temporary, when restarting the projector, the drive mode is automatically set to
normal.

- Permanent boost: Higher drive current to the CRT's, the lifetime of the CRT's will shorten but the light output

will be higher. This setting will be saved in the EEPROM. When restarting the projector, it will start up in boost
mode.

Ho

w to change the drive mode?

To change the drive mode:

1. Push the cursor key or to highlight 'CRT Drive Mode' (menu 1).

2. Press ENTER to display the CRT Drive mode menu (menu 2).

3. Push the cursor key or to highlight the desired drive mode (menu 3).

2. Press ENTER to activate the selected drive mode.

CRT Drive Mode

menu 1

CRT DRIVE MODE

NORMAL

ECONOMIC

TEMPORARY BOOST
PERMANENT BOOST

WARNING : permanent

boost mode reduces the lifetime

of the CRT's !

Select with or

then <ENTER>

<EXIT> to return

menu 2

CRT Drive Mode Warning

A warning, permanent BOOST mode in use, will be displayed to inform the user.
When text is on, this warning will be repeated every time a new source is selected.

WARNING

PERMANENT

BOOST MODE

IN USE !

COMMON SETTINGS

DYNAMIC ASTIGMATISM
GAMMA CORRECTIONS

CRT RUN IN CYCLE

CRT DRIVE MODE

MEMORYBANKS : ON

FLYBACK TURNOVER POINT

MENU POSITION : STANDARD

Select with or

then <ENTER>

<EXIT> to return

74

Memory Banks

What can be done?

The user has the possibility to create 8 different memory banks (formats) for each source. But, the maximum
allowed quantity of memory banks for all sources together is 32.
The option to create different memory banks for the same source can be switched ON or OFF.

Ho

w to select Memory Banks?

1. Push the cursor key or to highlight 'Memory Banks' (menu 1).

2. Press ENTER to toggle between ON and OFF.

ON : different memory banks available.
OFF : only one memory bank available.
If different memory banks are available for a source and the memory bank option is toggled to OFF,
only the first memory bank will be used to display the source.

menu 1

How to create a new memory bank?

1. Select your source. The projector selects the last used memory bank.

2. Press ENTER

3. Push the corresponding digit (between 1 and 8) of a non existing memory bank. (The memory banks can be
created in random order, e.g. first creating bank 5 and later bank 2.)

4. Make the necessary adjustments. When leaving the source, the new created memory bank will be saved for
later use.

Example: When source 1, video 15.6 kHz /60Hz is create on bank 4 and the vertical frequency changes to
50Hz, the projector will create a new block (due to the vertical frequency change) with the same bank number 4.

Ho

w to recall a specific memorybank for the actual source?

When the memory bank option is ON and a source is selected, this source will be displayed with the last used
memory bank settings.
An on-screen menu will give a indication of the memory bank nummer used (menu 1).
To switch to another memory bank :

1. Press ENTER to select the next memory bank in increasing order.
or

2. Enter the number of the desired memory bank with the digit keys.

In both cases, the on-screen indication will be update.

SOURCE XX

MEMORY

BANK

4

COMMON SETTINGS

DYNAMIC ASTIGMATISM
GAMMA CORRECTIONS

CRT RUN IN CYCLE

CRT DRIVE MODE

MEMORYBANKS : ON

FLYBACK TURNOVER POINT

MENU POSITION : STANDARD

Select with or

then <ENTER>

<EXIT> to return

COMMON SETTINGS

DYNAMIC ASTIGMATISM
GAMMA CORRECTIONS

CRT RUN IN CYCLE

CRT DRIVE MODE

MEMORYBANKS : ON

FLYBACK TURNOVER POINT

MENU POSITION : STANDARD

Select with or

then <ENTER>

<EXIT> to return

75

Flyback Turnover Point

What can be done?

The horizontal flyback time for horizontal frequencies can be long or short. The turnover point from long to short
can be installed by the user himself.

Set Up of

the Flyback Turnover Point

To set up the flyback turnover point:

1. Push the cursor key or to highlight 'Flyback turnover point' (menu 1).

2. Press ENTER to display the flyback turnover point (menu 2).
The actual turnover point frequency will be filled in.

3. Select the digits with the left or right cursor keys and enter the new value with the digit keys on the Remote.
The flyback turnover point frequency should be somewhere between 90 kHz and 130 kHz.

4. Press ENTER to select.

menu 1

FLYBACK TURNOVER POINT

Enter new frequency :

0 9 0 kHz

Use the or to select,

and reprogram with

numeric keys

Lowest point is 90 kHz.

Highest point is 130 kHz.

<ENTER> to confirm

<EXIT> to return.

menu 2

Menu Position

What can be done?

The bar scale menu, warning and message boxes can be displayed in the right lower corner or in the middle of
the screen.

Ho

w to change the position?

To change the position:

1. Push the cursor key or to highlight 'Menu position' (menu 1).

2. Press ENTER to toggle between STANDARD or MIDDLE.

menu 1

SERVICE MODE

PROJECTOR SET-UP

MEMORY MANAGEMENT

COMMON SETTINGS

I2C DIAGNOSTICS

VOLTAGE DIAGNOSTICS

PROJECTOR DIAGNOSTICS

Select with or

then <ENTER>

<EXIT> to return

76

What can be seen?

The I2C diagnostics menu gives an overview of the I2C failures inside the projector.
To scroll through the failure list, push the cursor key or .
The I2C address, IC number and module name will be given in I2C diagnostic menu.
When no errors are detected, the following message will appear on the screen:
"No errors on i2c-bus detected".

Ho

w to select?

1. Push the cursor key or to highlight 'I²C Diagnostics' (menu 1).

2. Press ENTER to display the diagnostic menu (menu 2).

12C Diagnostics

SERVICE MODE

PROJECTOR SET-UP

MEMORY MANAGEMENT

COMMON SETTINGS

I2C DIAGNOSTICS

VOLTAGE DIAGNOSTICS

PROJECTOR DIAGNOSTICS

Select with or

then <ENTER>

<EXIT> to return

menu 1

I2C DIAGNOSTICS

Failures :
addr IC number mod.name
48H IC200 DECODER

Select with or

then <ENTER>

<EXIT> to return

menu 2

Voltage Diagnostics

What can be seen?

The real value of the different voltages will be displayed on the voltage diagnostics menu.

Ho

w to start up?

1. Push the cursor key or to highlight 'Voltage diagnostics' (menu 1).

2. Press ENTER to display the voltage diagnostic menu (menu 2).

menu 1

VOLTAGE DIAGNOSTICS

+17V : 16.9 Volt

-17V : -17.1 Volt
+9V : +9 Volt
+12V : +11.9 Volt

-12V : -11.8 Volt
+30V : +29.8 Volt

-40V : -39.8 Volt
+110V : +110 Volt
+210V : +209 Volt
HTHD :

-conv :
+conv :
foc_lo :
foc_hi :

<EXIT> to return.

menu 2

SERVICE MODE

PROJECTOR SET-UP

MEMORY MANAGEMENT

COMMON SETTINGS

I2C DIAGNOSTICS

VOLTAGE DIAGNOSTICS

PROJECTOR DIAGNOSTICS

Select with or

then <ENTER>

<EXIT> to return

77

Projector Diagnostics

What can be seen?

A log of the last 5 failures with the run time when the failure happened is documented in the
Projector Diagnostics.

Ho

w to display the Projector Diagnostics?

1. Push the cursor key or to highlight 'Projector diagnostics' (menu 1).

2. Press ENTER to display the projector diagnostic menu (menu 2). The last failure will be displayed.

3. Use the cursor keys to scroll through the failure log.

4. Press ENTER to switch to the voltage diagnostics (menu 3).

5. Press EXIT to return to the projector diagnostics menu.

menu 1

VOLTAGE DIAGNOSTICS

+17V : 16.9 Volt

-17V : -17.1 Volt
+9V : +9 Volt
+12V : +11.9 Volt

-12V : -11.8 Volt
+30V : +29.8 Volt

-40V : -39.8 Volt
+110V : +110 Volt
+210V : +209 Volt
HTHD :

-conv :
+conv :
foc_lo :
foc_hi :

<EXIT> to return.

menu 3

PROJECTOR DIAGNOSTICS

Failure nr : 2
Runtime : 180h 30 min
Projector block nr : 4

Coincidence : ON
Deflection : OFF

SF : yes EHT fail : no
SF vert : no HD EHT : no
SF hor : no Fan Fail : yes
IBCL fail : no

Arrow keys to scroll,
<ENTER> to see the voltages,
<EXIT> to return.

menu 2

GEOMETRY

H PHASE

RASTER SHIFT

LEFT-RIGHT (E-W)

LEFT SIDE CORRECTION

TOP-BOTTOM (N-S)

V SIZE

V LINEARITY

H SIZE

BLANKING

Select with or

then <ENTER>

<EXIT> to return

ADJUSTMENT MODE

Select a path from below :

EYE-Q

GUIDED

RANDOM ACCESS

INSTALLATION

SERVICE

Source 01

Select with or

then <ENTER>

<EXIT> to return

MAIN MENU

Image Control
EYE-Q Control
Sound Control
Function keys

Service Menus

Select with or

then <ENTER>

<EXIT> to return

PROGRAMMABLE FUNCTION KEYS

Programmable Function Keys

What can be done with these keys?

The five function keys on top of the remote control can be programmed
as short cut keys (quick access) to almost any adjustment function.
See list futher in this chapter.

Ho

w can a Function Key be programmed?

A function key can only be programmed when in the service menus.
Perform the following:

1. Scroll through the menus until the desired function is on the menu.

2. Select this function by pushing the cursor keys up or down.

3. Press the desired function key for this function.
The following message: "Programming Function Key Fx"
will be displayed.
The message will disappear automatically and the function
key is programmed.

4. Leave the adjustment mode by pressing ADJUST.

5. The function key is available in the operational mode.

e.g. programming horizontal phase on key F4.

1. Press ADJUST to enter the main menu (menu 1).

2. Push the cursor keys or to select 'Service menu'.

3. Press ENTER to go into the adjustment menus.

A warning will be displayed (menu 2).

4. If qualified, press ENTER otherwise press EXIT and call for
technical assistance.

5. Select Randon by pushing the cursor keys or .

6. Press ENTER to display the Random Access mode menu (menu 3).

7. Push the cursor keys or to select 'Geometry'.

8. Press ENTER to display the Geometry menu (menu 4).

9. Push the cursor keys or to select H PHASE (menu 4).

10. Press 'F4' to program this key.

11. Press ADJUST to return to operational mode.

menu 1

menu 3

menu 4

WARNING

RISK OF INCORRECT
ADJUSTMENT OF THE
PROJECTOR.

The following
SERVICE menus
are reserved to,
and to be performed only
by qualified personnel !

If qualified, press
<ENTER> to continue, or
if not, <EXIT> to return.

menu 2

78

MESSAGES, WARNINGS AND FAILURES

INPUT 01

RGB2

Fh= 15.6 kHz

Fv= 050 Hz

SOURCE 01

RGB2

enter

password

x x x x

TEXT on

SOURCE 01

RGB2

xxxkHz

xxHz

TEXT off

PROJECTOR

ADDRESS :

003

WRONG

PASSWORD

!!!

When selecting a new source, informa­tion about this source will be displayed
on the screen. Source number, hori­zontal and vertical frequencies of the
displayed source.

Announcement of the selected source.

Message to enter your password.
Password contains 4 digits.

These messages will be displayed on
the screen when pushing the TEXT
key.

Text ON : the 'bar scale indication' will
be enabled during the change of an
analog control in the 'operational mode'
+ all warnings and failures will be dis­played.

Text OFF : the 'bar scale indication' will
be disabled during the change of an
analog control in the 'operational mode'
+ all warnings and failures will not be
displayed.

Indication of the projector address
when activating the 'ADDRESS' button
on the Remote with a pencil or other
small object.

Message when the entered password is
wrong.

WARNING :

source not

available

WARNING :

invalid

key entry

WARNING :

end of ad­just range

WARNING :

input

no longer

available

WARNING :

invalid

frequency

input

WARNING :

permanent

BOOST mode

in use !!!

WARNING :

Option not

installed !

WARNING :

Invalid Code Entry

The input is a valid input but the
source is not connected to the
input terminals or the input source
is switched off.

When a wrong key is pressed on
the Remote.

End of adjustment range.

The input source is no longer
available.

The entered frequency or applied
frequency of the source is out of
the projector's range.

The CRT drive mode is switched
to permanent boost.

Option not installed. e.g. Video
selected but no decoder installed.

The entered password is incorrect

79

80

FAILURE

I2C error

addr. : 7FH3

FAILURE

short

circuit on

I2C bus

FAILURE

invalid input

FAN FAILED

Projector will

switch off

FAILURE

EYE-Q

configuration failed

Hardware failure. Call a qualified serv­ice technician for repair.

Hardware failure. Call a qualified serv­ice technician for repair.

Input not valid

Projector switched off due to a fan fail.

Error occured while configuring the
EYE-Q module.

81

ADJUSTMENT BLOCKS AND SOURCE NUMBERS 90-99

Adjustment Blocks (Memory Blocks)

What are adjustment block?

As the projector is digitally controlled, all geometry and convergence adjustments are stored in the projector’s
memory as numeric values. These numeric values are used to control digital potentiometers which in turn, con­trol the projector. Each source connected to the projector has a unique set of adjustment data which is automati­cally downloaded into the projector’s digital potentiometers once the source has been selected. This set of
adjustment data is referred to as an “adjustment block”.

An adjustment table is automatically created for a source when the source is first connected to the projector and
the Adjustment mode is entered. If other sources have already been connected to the projector and geometry
and convergence adjustments have been performed on these sources, the projector will use Linear Digital
Interpolation to create a new block for the new source. This block will provide an initial set of adjustments for the
new source that have been calculated by the projector from “previous experience”.

The projector’s memory has the capacity to store 32 adjustment blocks. The adjustment block consists of two
parts, the block header and the data representing the values for all adjustments (eg. Convergence and
Geometry) in the projector for the source the block corresponds to. The block header contains the basic char­acteristics of the source and the projector configuration used to display the source.

Built up of

block

Block Header Example of Block Header

Block Number 01
Source Number 01
Horizontal Frequency 15.6 kHz
Vertical Frequency 50 Hz
Input Type Video
Scan Switch Configuration Front/Ceiling

The data representing the various adjustments for the source follows the block header.

Source Numbers 90-99

Why used?

Source numbers 90 - 99 are used to assign an additional adjustment block to a source. This additional adjust­ment block may contain different geometry and convergence settings, sync fast/slow positions and enhanced
blue on/off settings. The relationship between source numbers 1 - 5 and 91 - 95 is shown in the diagram on the
next page. The alternate adjustment block for sources 1 - 5 is activated by selecting the corresponding source
number 1 - 5. Once this source number is selected, the alternate block of adjustment data is in use and may be
modified via the adjust mode of the projector. The alternate adjustment block is automatically stored.

Ho

w to create a second block?

Follow the steps below to create a second adjustment block for a source between 0 and 9.

1. Select the source between 0 and 9 that the second adjustment block is to be created for.

2. Select the corresponding source number between 90 and 99. The adjustment block for the source number
between 0 and 9 is copied to the corresponding source number between 90 and 99.

3. Enter the adjust mode and make any desired changes (geometry, convergence, sync fast/slow, enhanced
blue on/off) to the second adjustment block.

4. Exit the adjust mode.

82

source input 0

source input 1

source input 2

source input 9

source number 0 - Block header A
source number 90 - Block header A, different analog settings

source number 1 - Block header B
source number 91 - Block header B, different analog settings

source number 2 - Block header C
source number 92 - Block header C, different analog settings

•

•

•

source number 9 - Block header J
source number 99 - Block header J, different analog settings

RS-232 CODES

Baud Rate: 9600
Data Length: 8 Bits
Parity: None
Stop Bit: 1

Structure: Hex (nine bytes)
Byte 1 - wake-up command. Always "02"
Byte 2 - command offset. Normally "00", changed if there is another "02"in the command.
Byte 3 - Projector address. Normally "00" will address all projectors.
Byte 4 - Main Command
Byte 5 - additional data
Byte 6 - additional data
Byte 7 - additional data
Byte 8 - additional data
Byte 9 - checksum. Add byte 3 - 8 without offset, then add offset and take last two Bytes.

Power Toggle: 02.00.00.0E.00.00.00.00.0E
Power On: 02.00.00.51.0A.00.00.01.5C
Power Off: 02.00.00.51.0A.00.00.00.5B

Enter: 02.00.00.07.00.00.00.00.07
Exit: 02.00.00.08.00.00.00.00.08
Adjust: 02.00.00.09.00.00.00.00.09
Text Toggle: 02.00.00.0D.00.00.00.00.0D

Cursor Up: 02.00.00.21.00.00.00.00.21
Cursor Down: 02.00.00.22.00.00.00.00.22
Cursor Right: 02.00.00.23.00.00.00.00.23
Cursor left: 02.00.00.24.00.00.00.00.24

Button 0: 02.00.00.10.00.00.00.00.10
Button 1: 02.00.00.11.00.00.00.00.11
Button 2: 02.00.00.12.00.00.00.00.12
Button 3: 02.00.00.13.00.00.00.00.13
Button 4: 02.00.00.14.00.00.00.00.14
Button 5: 02.00.00.15.00.00.00.00.15
Button 6: 02.00.00.16.00.00.00.00.16
Button 7: 02.00.00.17.00.00.00.00.17
Button 8: 02.00.00.18.00.00.00.00.18
Button 9: 02.00.00.19.00.00.00.00.19

83

84

Contrast +: 02.00.00.28.00.00.00.00.28
Contrast -: 02.00.00.29.00.00.00.00.29
Brightness +: 02.00.00.2A.00.00.00.00.2A
Brightness -: 02.00.00.2B.00.00.00.00.2B
Color +: 02.00.00.2C.00.00.00.00.2C
Color -: 02.00.00.2D.00.00.00.00.2D
Tint +: 02.00.00.2E.00.00.00.00.2E
Tint -: 02.00.00.2F.00.00.00.00.2F
Sharpness +: 02.00.00.36.00.00.00.00.36
Sharpness -: 02.00.00.37.00.00.00.00.37

All commands are in hex and will be entered differently with each control system.
For example:
Phast = Power On: $02,$00,$00,$51,$00,$00,$00,$01,$5C
AMX= Power On: h02,h00,h00,h51,h00,h00,h00,h01,h5C
Crestron = Power On: \x02\x00\x00\x51\x00\x00\x00\x01\x5C

Pin Configuration: 9-pin din female.
Pin 2 - RXD
Pin 3 - TXD
Pin 5 - Ground
Straight thru wire configuration

85

CEILING/FLOOR CONFIGURATION

(B)

20.70

6.88

14.25

87

44.19

28.87

O

n.

A
B
C
D
S
T

T
T

Floor Mount

Ceiling Mount

2.

THROW DISTANCE

10.5o PROJECTION ANGLE

verall Dimensions: Length: 44.20 in x Width: 26.77 x Height: 14.25 i
= Center of Gravity = 9.39 in.
= Center = 10.57 in.
= Bracket Height = 2.87 in.
= Lens to Center of Bracket = 20.70 in.

creen Dimensions ________H x ________W

OFFSET

SCREEN
HEIGHT

D = Throw Distance Factors

D for 16 x 9 screens: (screen width x 1.43) = __________ inches
D for 4 x 3 screens: (screen width x 1.48) = __________ inches

10.32

14.25

1.08

28.87

44.19

10.57

20.70

3.93

10.5o PROJECTION ANGLE

THROW DISTANCE

6.88

SCREEN
HEIGHT

OFFSET

9

86

DIMENSIONS

Bottom View

Side View

Front View

44.196

15.32

1.076

26.772

87

SPECIFICATIONS

Scan Frequency: Horizontal: 32-132 kHz, Vertical: 37-210 Hz
Optical Resolution: HD-120 lenses, 12 line pairs per, mm, 1250 TV lines
Video Standards: NTSC/PAL/SECAM
Video Resolution: 1250 TV lines
Retrace Time: Horizontal: 1.8 uS, Vertical: 300 uS
Bandwidth: 180 MHz
CRTs: 9-inch, high definition, liquid coupled tubes with electromagnetic focus and color

filters

Lenses: Super high definition, fully color corrected F1.15 lenses
Inputs: RGB/Component
Color Balance: Four user selectable settings: 3200K, 5400K, 6500K, 9300K, and Custom
Input Memories: 32 separate memories with 8 memories per scan frequency
Internal Setup Pattern: Crosshatch, Focus
Light Output: 1300 lumens/250 ANSI lumens
Picture Size: 90-300 in. (4:3) diagonal
Throw Distance: 1.43 x width (widescreen), 1.48 x width (standard 4:3)
Vertical Offset: Maximum vertical offset = 5°
Configurations: Front or rear, floor or ceiling mount
Aspect Ratios: Anamorphic, widescreen, 4:3
Contrast Ratios: 100:1 (JIS Method). 20:1 (HDTV Method)
Convergence: Digital zone convergence with 81 individual zones
Focus: Digital focus with multiple zones
Power Requirements: 110 VAC, 50/60 Hz (220V International version)
Power Consumption: 800 W
Cabinet Dimensions: Width: 26.77 in./680 mm

Depth: 44.20 in./1123 mm
Height: 14.25 in./362 mm (without feet), 15.33 in./389 mm (with feet)

Weight: 187 lbs./85 Kg.
Regulatory Approvals: Complies with FCC Class "B", CE, C-Tick
Storage: 10-122° F (-12-50° C)
Operating Environment: 32-104° F (0-40° C)
Humidity: 0-90% non-condensing
Included Accessories: Remote control, AC power cord and Owner's Operating Manual
Warranty: Service Labor and Parts (except lamp): Runco warrants the product for one

(1) year from the date of delivery to the end user.
Lamp: 6 months or 1000 hours (which ever comes first).

RUMA-009450 rev 1-02

Runco International • 2463 Tripaldi Way • Hayward, CA 94545 • ph [phone] • fax [phone] • www.runco.com