Runco CL-710LT, CL-710 User Manual 2

OWNER’S OPERATING MANUAL

CL-710 / CL-710LT

Congratulations on your purchase of a Runco video product and welcome to the Runco family! We believe Runco produces “The World’s Finest Home Theater Products”. With proper installation, setup and care, you should enjoy many years of unparalleled video performance. Please read this consumer protection plan carefully and retain it with your other important documents.

This is a LIMITED WARRANTY as defined by the U.S. Consumer Product Warranty and Federal Trade Commission Improvement Act.

WHAT IS COVERED

UNDER THE TERMS OF THIS WARRANTY:

SERVICE LABOR: Runco will pay for service labor by an approved Runco service center when needed as a result of manufacturing defect for a period of two (2) years from the effective date of delivery to the end user.

PARTS: Runco will provide new or rebuilt replacement parts for the parts that fail due to defects in materials or workmanship for a period of two (2) years from the effective date of delivery to the end user. Such replacement parts are then subsequently warranted for the remaining portion (if any) of the original warranty period.

WHAT IS NOT

COVERED UNDER THE TERMS OF THIS WARRANTY:

This warranty only covers failure due to defects in materials and workmanship that occur during normal use and does not cover normal maintenance. This warranty does not cover cabinets or any appearance item; failure resulting from accident, misuse, abuse, neglect, mishandling, misapplication, faulty or improper installation or setup adjustments; improper maintenance, alteration, improper use of any input signal; damage due to lightning or power line surges, spikes and brownouts; damage that occurs during shipping or transit; or damage that is attributed to acts of God. In the case of remote control units, damage resulting from leaking, old, damaged or improper batteries is also excluded from coverage under this warranty.

CAUTION: DAMAGE RESULTING DIRECTLY OR INDIRECTLY FROM IMPROPER INSTALLATION OR SETUP IS SPECIFICALLY EXCLUDED FROM COVERAGE UNDER THIS WARRANTY. IT IS IMPERATIVE THAT INSTALLATION AND SETUP WORK BE PERFORMED ONLY BY AN AUTHORIZED RUNCO DEALER TO PROTECT YOUR RIGHTS UNDER THIS WARRANTY. THIS WILLALSO ENSURE THAT YOU ENJOY THE FINE PERFORMANCE YOUR RUNCO PRODUCT IS CAPABLE OF PROVIDING WHEN INSTALLED AND CALIBRATED BY RUNCO AUTHORIZED PERSONNEL.

RIGHTS, LIMITS AND EXCLUSIONS:

Runco limits its obligations under any implied warranties under state laws to a period not to exceed the warranty period. There are no express warranties. Runco also excludes any obligation on its part for incidental or consequential damages related to the failure of this product to function properly. Some states do not allow limitations on how long an implied warranty lasts, and some states do not allow the exclusion or limitation of incidental or consequential damages. So the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights, and you may also have other rights that vary from state to state.

Limited Warranty

EFFECTIVE WARRANTY DATE:

This warranty begins on the effective date of delivery to the end user. For your convenience, keep the original bill of sale as evidence of the purchase date.

IMPORTANT: WARRANTY REGISTRATION:

Please fill out and mail your warranty registration card. It is imperative that Runco knows how to reach you promptly if we should discover a safety problem or product update for which you must be notified.

TO OBTAIN SERVICE, CONTACT YOUR RUNCO DEALER:

Repairs made under the terms of the Limited Warranty covering your Runco International video product will be performed at the location of the product, during usual working hours, providing location of product is within normal operating distance from a Runco Authorized Service Center. If, solely in Runco’s judgement, location of product to be repaired is beyond normal operating distance of the closest Runco Authorized Service Center, it is the owner’s responsibility to arrange for shipment of the product for repair. These arrangements must be made through the selling Runco dealer. If this is not possible, contact Runco directly for a return authorization number and shipping instructions. Runco will return product transportation prepaid in the United States, unless no product defect is discovered. In that instance, shipping costs will be the responsibility of the owner.

ADDITIONAL INFORMATION:

To locate the name and address of the nearest Runco Authorized Service location, or for additional information about this warranty, please call, write or visit our website:

CUSTOMER SERVICE DEPARTMENT

RUNCO INTERNATIONAL

2900 Faber Street

Union City, CA 94587

Ph: (510) 324-7777 / Fax: (510) 324-9300

www.runco.com

Runco CL-710/ CL-710LT User’s Manual

Runco CL-710/ CL710LT Video Projector User’s Manual

Thank you for your purchase of this quality Runco video projector! It has been designed to pr ovide y ou with the qualit y of video that is expected in a home theater. For the best performance, please read this manual carefully as it is your guide through the menus and operation.

WARNING

This symbol is intended to alert the user to the presence of

CAUTION

RISK OFELECTRIC SHOCK

DO NOTOPEN

CAUTION: TOREDUCE THE RISKOF ELECTRIC SHOCK.

DO NOTREMOVE COVER (ORBACK)

NO USERSERVICEABLE PARTSINSIDE.

REFER SERVICINGTO QUALIFIED SERVICEPERSONNEL.

uninsulated " dangerous voltage " within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock.

This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Do not use this projector near water, outdoors or otherwise exposed to the elements.

5. Clean only with a dry cloth.

6. Do not block any ventilation openings.

7. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

8. Do not defeat the safety feature of the polarized or grounding type plug. A polarized type plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for the replacement of the obsolete outlet.

9. Do not connect the RJ-11 RS-232 jack to a telephone line connection.

10. The 12V trigger only output DC 12V signal for triggering. Do not connect to any other powe r input or output. This could cause damage to this unit.

11. Only use accessories specified by RUNCO International.

12. Keep the packing material in case the projector should ever need to be shipped.

13. Unplug this projector during lightning storms or when it will not be used for an extended period of time.

14. The lamp becomes extremely hot during operation. Allow the projector to cool down for approximately 45 minutes prior to removing the lamp assembly for replacement. Do not operate lamps beyond the rated lamp life. Excessive operation of lamps beyond rated life could cause them to explode in rare occasions.

15. Refer all servicing to qualified service personnel. Servicing is required when the pr ojector has been damaged in any way, objects have fallen or spilled into the projector, the projector has been exposed to rain or moisture, does not operate normally, or has been dropped.

WARNING

Runco CL-710/ CL-710LT User’s Manual

Table of Contents

WARNING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

1.Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Projector Outlook . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Front / Upper Side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Rear / Bottom Side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Controls and Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Connector Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2.Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Projector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Connect the Power Cord . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Adjust the Lens Zoom/Focus ring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Adjust the height . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Installation For CL-710 (With 1.40 - 1.60 Lens) . . . . . . . . . . . . . . . . . . 11

Throw Distance Chart For CL-710 (With 1.40 - 1.60 Lens) . . . . . . . . .12

Installation For CL-710LT (With 1.85 - 2.40 Lens) . . . . . . . . . . . . . . . . 13

Throw Distance Chart For CL-710LT (With 1.85 - 2.40 Lens) . . . . . . 14

3.Connecting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Connecting Video Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Video / S-Video / Component (Interlaced Video) . . . . . . . . . . . . . . . . . . . . . . . . 15

Progressive Component (DTV Y/PB/PR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

RGBHV (DTV RGB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Connecting a Computer (DVI/ HDCP) . . . . . . . . . . . . . . . . . . . . . . . . .17

4.Basic Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Turning on the Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Zoom/ Focusing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Selecting Video Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Selecting "ASPECT RATIO" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Direct Picture Adjust (Menu Bypass) . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Setting Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Selecting Input Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

PIP/ PBP function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Turning off the Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

5.Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Using the Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Main Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Picture Quality Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

Aspect Ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 5

6.Additional Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Warning Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Replace the Lamp (Contact your Runco Dealer) . . . . . . . . . . . . . . . . . . 27

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

RS-232 Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

WARNING

Runco CL-710/ CL-710LT User’s Manual

1. Overview

Features

■ Native 16x9 Aspect Ratio DMD

■ High Contrast and Picture Quality

12 degree mirrors with dark metal process

■ Fantastic Dynamic Performance and Rich Gray-scale

6-segment 5x color wheel with wide color space

■ TIR (Total Internal Reflection) Prism

Light engine with Cat's Eye optics for highest performance capable from an HD-2 DMD.

■ Wide Variety of Inputs

This unit can support various video formats, including Composite, S-Video, Component, DTV Y/P and Computer signals. The HDTV input (DTV Y/P least amount of signal degradation caused by longer cable runs.

B/PR and DTV RGB) is input through RGB BNC port, providing the

B/PR, DTV RGB

■ HDTV Ready

480P, 1080i and 720P (576P PAL Version) formats are all compatible with this unit (via an external DTV decoder , not provided).

■ De-interlacing with 3:2 Pull-down

Using Runco's proprieta ry De-interlacing technology, this projector provides exceptional scaling and film to video (3:2 pulldown) conversion for the most artifact-free images possible.

■ PIP/ PBP function

Picture in picture/ Picture by picture functions allow you to display two inputs on the screen at the same time.

■ Video Memory

This projector allows the user to store up to three diff erent settings per input.

1. Overview

Runco CL-710/ CL-710LT User’s Manual

Projector Outlook

❚ Front / Upper Side

1. Front Lamp Cover

Remove this cover when replacing the lamp. (See page 27.)

2. Projection Lens

3. Front IR Sensor

4. Ventilation Holes (exhaust)

5. Focus Ring and Zoom Ring Access

Adjusts the focus and zoom of image.

❚ Rear / Bottom Side

6. Power LED and Lamp LED

Show the status of power and lamp. For more details, see "Control Panel" on page 5.

7. Top IR Sensor

8. Runco Logo (Can be turnedd off, see "Options" on page 24.)

1. Connector Panel

For more details, see "Connector Panel" on page 6.

2. AC Power IN Socket

3. AC Power Switch

AC main power switch

4. Ventilation Holes (intake)

5. Rear Adjusters

Adjust the height or projection angle

1. Overview

6. Front Adjusters

Adjust the height or projection angle

7. Ceiling Mount Holes

The connecting holes with ceiling mounting device.

8. Ventilation Holes (exhaust)

9. Cable Access Cover

Controls and Functions

❚ Control Panel

Runco CL-710/ CL-710LT User’s Manual

1. POWER LED Indicate the status of the power

■ Orange when the AC power cord is plugged into the wall outlet (standby mode). Once in the

standby mode, you can turn on the projector by pressing the ON key on the remote control for ONE second.

■ Green when the power is turned on (operational mode).

■ Flashing Orange for the first 45 seconds after power-up indicating that the lamp is warming up.

■ Flashing Green for 90 seconds after the projector was powered off indicating that the lamp is

cooling down.

2. LAMP LED

Indicates the status of lamp

■ Red when the lamp has developed a problem. Please contact your Runco Dealer for assistance.

3. ZOOM RING

Adjust the size of the image

■ Rotate right to enlarge the image, and rotate left to make the image smaller.

4. FOCUS RING

Adjust the focus of the image

■ Rotate the focus ring right or left to focus the image.

1. Overview

Runco CL-710/ CL-710LT User’s Manual

❚

Connector Panel

1. Video (RCA Jack)

Composite video signal input.

2. S-Video (mini DIN 4-pin)

Y/C (S-video) signal input

3. Component (RCA Jacks)

480i Component (Y/C

B/CR) video signal input

4. RGB/ HDTV (BNC) or Progressive Scan DVD players

DTV Y/P

B/PR or DTV RGB video signal input.

5. DVI/ HDCP

Digital/ Analog signal input.

6. RS-232C (RJ-11 Jack)

RS-232C control signal input.

7. 12v Trigger (mini jack with the diameter of 5.5 mm outside and 2.5 mm inside)

+12V output, active when the projector is turned on.

1. Overview

❚

Remote Control

Anamorphic

For 16: 9 DVDs.

4 X 3

The input signal will be scaled to fit 4: 3 display mode in the center of screen.

LPos+, LPos-

Letterbox position

Letterbox

Letterbox mode. Image in letterbox format is enlarged to fit 16:9 full screen display and the upper / lower portion are “blanked off”.

VirtualWide

4:3 image is enlarged NONlinearly in horizontal direction to fit 16: 9 full screen display.

Runco CL-710/ CL-710LT User’s Manual

ON Hold down this button for ONE second to turn on the unit.

OFF

Press this button to turn off the unit.

M1, M2, M3, Default

Recall video memory sequentiall (see "Selecting Video Memory" o page 18)

Color

Adjust color intensity

Brightness

Adjust picture brightness

Contrast

Adjust picture contrast

Tint

Adjust color tones

1. Overview

Runco CL-710/ CL-710LT User’s Manual

Arrow (c,e,d,f) Use to select the menu or to make various adjustments.

Enter

Enter the setting of items in the menu.

Picture

Access the Picture Setting menu (see "Picture Quality Adjustments" on page 23)

Info

Access the projector information

Exit

Exit and save the setting(s) of items in the menu.

Turns on/off the on-screen display menu.

PBP (Picture by Picture)

Enable the PIP function.

ACTIVE

Switch to the active window in PIP display mode.

PIP (Picture in Picture)

Enable the PIP function. Use ARROW keys to adjust the position of the PIP window (see "PIP/ PBP function" on page 20)

PIP+

Enlarge the size of PIP window.

PIP-

Shrink the size of PIP window.

Video

Composite video signal input

S-Video

S-Video signal input

Comp

Component Y/C

B/CR input

Comp HD

DTV Y/P

B/PR signal input

RGB HD

DTV RGBHV signal input

DVI

Digital/ Analog signal input

1. Overview

2. Installation

Remote Control

Runco CL-710/ CL-710LT User’s Manual

Push forward on the tap and lift to open the cover. Install the two AAA batteries with the correct polarity, then close the cover.

Notes on Batteries

■ Make sure that the battery polarities are correct when installing the batteries.

■ Do not mix an old battery with a new one or different types of batteries.

■ If you will not use the remote control for a long time, remove the batteries to avoid damage from battery

leakage.

Notes on Remote Control Operation

■ Make sure that there is nothing obstructing the infrared beam between the remote control and the IR receiver

on the projector.

■ The useable range is between 3m/ 9.8 feet (from the front of the projector) and 4m/ 13.1 feet (from the top of

the projector) within 30 degree horizontal angle and 15 degree vertical angle.

Projector

❚ Connect the Power Cord

Plug the supplied power cord into the AC inlet in the rear of this unit. (AC 100V ~ 240V)

Turn on the main power switch in the rear of this unit (next to the AC inlet). The POWER LED will light up in orange. Press ON key on the remote control f or ONE second to turn on the unit.

2. Installation

Runco CL-710/ CL-710LT User’s Manual

❚

Adjust the Lens Zoom/Focus ring

Adjust the projected image size you need with the zoom ring on the lens. To focus the image, rotate the focus ring on the lens.

Focus

❚ Adjust the height

There are 4 screw adjusters on the bottom of this unit. You can adjust the height or projection angle of this unit by using these adjusters.

Zoom out

Zoom in

2. Installation

Runco CL-710/ CL-710LT User’s Manual

Installation For CL-710 (With 1.40 - 1.60 Lens)

Ceiling

Screen __________ (H) x __________ (W)

B) THROW DISTANCE:

CL-710 16 x 9 Screens:

Minimum: (screen width x 1.40) = __________ inches

Maximum: (screen width x 1.60) = __________ inches

C) VERTICAL OFFSET:

Screen width x 0.052 = _________ inches from the center of the lens.

Floor

2. Installation

Runco CL-710/ CL-710LT User’s Manual

Throw Distance Chart For CL-710 (With 1.40 - 1.60 Lens)

CL-710 @ 1280 x 720

Screen Height Screen Width

40.5 72 100.80 115.20 3.74 43 77 107.80 123.20 4.00 45 80 112.00 128.00 4.16 47 84 117.12 133.86 4.35 49 87 121.80 139.20 4.52 50 89 124.60 142.40 4.63

51.5 92 128.80 147.20 4.78 52 93 130.20 148.80 4.84 54 96 134.40 153.60 4.99 56 100 140.00 160.00 5.20 58 103 144.20 164.80 5.36

58.5 104 145.60 166.40 5.41 60 107 149.80 171.20 5.56 61 109 152.60 174.40 5.67 63 112 156.80 179.20 5.82 65 116 162.40 185.60 6.03

67.5 120 168.00 192.00 6.24 72 128 179.20 204.80 6.66 80 142 198.80 227.20 7.38 82 146 204.40 233.60 7.59 90 160 224.00 256.00 8.32

Min Throw

Distance

Max Throw

Distance

Verti c al Of f set

Position

Screen Hight Screen Width Min TD Max TD Vertical Offset

(SWx1.40) (SWx1.60) Screen Width x 0.052

2. Installation

Runco CL-710/ CL-710LT User’s Manual

Installation For CL-710LT (With 1.85 - 2.40 Lens)

Ceiling

Screen __________ (H) x __________ (W)

B) THROW DISTANCE:

CL-710LT 16 x 9 Screens:

Minimum: (screen width x 1.85) = __________ inches

Maximum: (screen width x 2.40) = __________ inches

C) VERTICAL OFFSET:

Two inches offset means that the center of the projection lens is 2" above

the top of the screen (inverted ceiling) or 2" below the bottom of

the screen (upright floor mount).

Floor

2. Installation

Runco CL-710/ CL-710LT User’s Manual

Throw Distance Chart For CL-710LT (With 1.85 - 2.40 Lens)

CL-710LT @ 1280 x 720

Screen Height Screen Width

40.5 72 133.20 172.80 2.0" 43 77 142.45 184.80 2.0" 45 80 148.00 192.00 2.0" 47 84 154.77 200.78 2.0" 49 87 160.95 208.80 2.0" 50 89 164.65 213.60 2.0"

51.5 92 170.20 220.80 2.0" 52 93 172.05 223.20 2.0" 54 96 177.60 230.40 2.0" 56 100 185.00 240.00 2.0" 58 103 190.55 247.20 2.0"

58.5 104 192.40 249.60 2.0" 60 107 197.95 256.80 2.0" 61 109 201.65 261.60 2.0" 63 112 207.20 268.80 2.0" 65 116 214.60 278.40 2.0"

67.5 120 222.00 288.00 2.0" 72 128 236.80 307.20 2.0" 80 142 262.70 340.80 2.0" 82 146 270.10 350.40 2.0" 90 160 296.00 384.00 2.0"

Min Throw

Distance

Max Throw

Distance

Verti c al Of f set

Position

Screen Hight Screen Width Min TD Max TD Vertical Offset

(SWx1.85) (SWx2.40) 2.00”

Note: Two inches offset means that the center of the projection lens is 2” above the top of the scr een (inv erted ceiling)

or 2” below the bottom of the screen (upright floor mount).

2. Installation

Runco CL-710/ CL-710LT User’s Manual

3. Connecting

When connecting, make sure to:

1. Turn off all equipment before making any connections.

2. Use the correct signal cables for each source.

3. Ensure the cables are firmly connected.

4. Connect all audio signals to external speakers. This projector is not equipped with speakers.

Connecting Video Inputs

❚ Video / S-Video / Component (Interlaced Video)

DVD Player

3. Connecting

Runco CL-710/ CL-710LT User’s Manual

❚

Progressive Component (DTV Y/PB/PR)

❚ RGBHV (DTV RGB)

DTV Source

The RGB BNC input supports two kinds of HDTV formats: Progressiv e component (DTV Y/PB/PR) and DTV RGB. The unit will auto detect the resolution automatically.

3. Connecting

Connecting a Computer (DVI/ HDCP)

Runco CL-710/ CL-710LT User’s Manual

PC or Notebook

This unit is compatible with the following computer resoultions: 1280x720, 1024x768, 800x600, 640x480.

3. Connecting

Runco CL-710/ CL-710LT User’s Manual

4. Basic Operation

Turning on the Power

■ The Power LED lights orange when power is applied

and the power switch is turned on.

■ Press and hold the ON key on the remote control

for ONE second to turn on the unit. The POWER LED will blink orange during warm up period, then light solid green.

■ " Searching…." will be displayed on the scr een bef or e

the projector identifies the input signal. This message will remain on the screen until a valid signal is detected.

■ If an incompatible input signal exceeds the range of

the projector a "Not supportive timing" message will be displayed on the screen. This message will remain on the screen until you change the input signal.

Zoom/ Focusing

■ Adjust the projection image size you need with the

zoom ring on the lens. To focus the image, rotate the focus ring on the lens.

Selecting Video Memory

■ Press M1, M2, M3 buttons to recall settings in the

memory.

■ Press Default to select the default setting.

Zoom out

Focus

Zoom in

4. Basic Operation

Selecting "ASPECT RATIO"

■ Select the proper aspect ratio according to the

format of signal content. Th er e are four aspect ratios for choice.

■ Anamorphic: 4:3 image is stretched horizontally to

fit the 16: 9 screen. This is for 16:9 DVDs.

■ 4 X 3: The input signal will be scaled to fit 4 : 3

display mode in the center screen.

■ LPos+, LPos-: Adjust Letterbox image vertical

position.

■ Letterbox: Image in letterbox format is enlarged to

fit 16:9 full screen display and the upper/lower portion are compressed.

■ VirtualWide: This transforms a 4x3 image to a

16x9 image.

Direct Picture Adjust (Menu Bypass)

Runco CL-710/ CL-710LT User’s Manual

■ Press Color to adjust color intensity.

■ Press Brightness to adjust picture brightness.

■ Press Contrast to adjust picture contrast.

■ Press Tint to adjust color tones.

Setting Menu

■ Press the Menu button to turn on /off the on-screen

menu.

■ Use the ARROW buttons (c,e,d,f) to select the

menu or to make various adjustments.

■ Press the Enter or f button to enter the setting of

items in the menu, or press the Exit button to leav e and save the setting of items in the menu.

■ For more detailed settings, see Chapter 5 Menu on

page 22.

■ Press Picture to access the picture setting menu.

■ Press Info to access projector information.

4. Basic Operation

Runco CL-710/ CL-710LT User’s Manual

Selecting Input Source

■ When this unit is turned on, it will search for the

input source you selected last time.

■ You may select the input source directly on the

remote control.

PIP/ PBP function

■ Press the PIP button to enable the PIP function

■ For PIP purposes, there are two groups of inputs

separated by their display modes: Video Group: Video, S-Video and Component Y/C C

R inputs

Graphic Group: HDTV input and Computer input.

■ The PIP can show one input from the Graphic Group

within one input from the Video Group , or sho w one input from Video Group within one input from the Graphic Group.

■ Press the PIP button to switch to the main window

or turn off PIP function.

■ Select the input source of main window by pressing

the INPUT button.

■ Press the ACTIVE button to switch to the active

window. You can change the input signal setting in active window.

■ Press PIP+ or PIP- to adjust the size of PIP window.

■ Adjust the position of the PIP window with the

ARROW keys (c,e,d,f).

■ Press PBP to enable the PBP function.

4. Basic Operation

Turning off the Power

■ Press the OFF key on the remote contr ol to turn

off the unit.

■ The POWER LED will blink green and the fans will

speed up for a quick cool down. The projector will not respond to any command for 90 seconds.

■ The POWER LED will light solid orange once the

cooling down cycle has completed.

■ After turning off the unit, the POWER LED will

blink green and the fans will operate at high speed for 90 seconds.

■ Fans will run for three minutes to cool.

■ You may turn the projector back on after the first

90 seconds.

Runco CL-710/ CL-710LT User’s Manual

4. Basic Operation

Runco CL-710/ CL-710LT User’s Manual

5. Menu

Using the Menu

This unit is equipped with an on-screen display (OSD) menu for making various adjustments and settings. There are four different menu languages; see page 24 Language setting for more details.

■ Press the Menu button to turn on /off the on-screen display men u.

■ Use the ARROW buttons (c,e,d,f) to select the menu or to make various adjustments.

■ Press the Enter or f button to enter the setting of items in the menu, or press the Exit button to leave and save

the setting of items in the menu.

Main Menu

Runco CL-710 > Video S-Video Component Component HD RGB HD DVI-I

---------------------- Aspect Ratio Options

Setup

Source selection and picture quality adjustments

Aspect ratio selection Option selection

Setup selection

When the Menu button is pressed on the remote control, the main menu will appear on-screen. An example of the main menu is shown above. Use c or d button to move the item you want to choose and then press the Enter or f button.

The active source is indicated b y an arrow ( current source.

5. Menu

> ) to the left of the source; note that in the example above, Video is the

Picture Quality Adjustments

Runco CL-710/ CL-710LT User’s Manual

Runco CL-710 > Video S-Video Component Component HD RGB HD DVI-I

---------------------- Aspect Ratio Options

Brightness Contrast Color Tint Sharpness Filter Temperature Store Recall

Adjustment

Set Up

To access the picture quality adjustments, press Menu, highlight the active source (indicated by the arrow) and press Enter or f. The picture quality sub-menu will then appear (see above).

To make an adjustment to a particular function, highlight the function with the c or d arrow button and press Enter or fto activate a scroll bar for that adjustment.

To enter into the memory selection menus, use Store and Recall menus to save and load three different memories. There are three memories: Memory 1, Memory 2 and Memory 3.

Aspect Ratio

Runco CL-710 > Video S-Video Component Component HD RGB HD DVI-I

---------------------- Aspect Ratio Options

Set Up

There are four aspect ratios available that can be selected for video signal inputs.

16:9 Screens:

■ ANAMORPHIC: The image is compressed vertically, but anamorphic software will appear properly

proportioned. This is best suited for use with 16:9 DVD's.

> Anamorphic (16:9) Standard (4:3) Letterbox Virtual Wide

Adjustment

Active Image Area

5. Menu

Runco CL-710/ CL-710LT User’s Manual

■ 4 x 3: The input signal will be scaled to fit in the center of the 16:9 screen.

Active Image Area

■ LETTERBOX: The image in the Letterbox mode will be stretched vertically, and the top and bottom portion

'blanked off'. This ratio is best suited for LaserDisc movies or non-anamorphic DVD's.

Active Image Area

■ VIRTUAL WIDE: A 4:3 image is transformed into a 16x9 image to allow the user to watch SDTV on their

widescreen.

Options

Runco CL-710 > Video S-Video Component Component HD RGB HD DVI-I

---------------------- Aspect Ratio Options

Set Up

> Reset Adjustments Language Picture Orientation Logo Light Sleep Timer Lamp Hours OSD Position PC & HD Adj.

Press Enter on selected feature to open the adjustment menu. Reset Adjustments: Use this function to reset all values of the current source back to factory default. Language: There are 4 different menu languages are available: English, Spanish, French and German. Picture Orientation: The projector could be installed on a ceiling or behind a screen, or with one or more mirrors.

There are four settings: FLOOR FRONT, CEILING FRONT, FLOOR REAR, and CEILING REAR.

Options

Logo Light: To turn on or off projector logo light.

5. Menu

Runco CL-710/ CL-710LT User’s Manual

Sleep Timer: To setup auto off minutes. The setting timer is from 10 minutes to 3 hours. Lamp Hours: To check for total time lamp age. OSD Position: To adjust horizontal and vertical positions of OSD. PC & HD Adj.: The following settings are only a vailable with a PC or DTV RGB signal. There is no position adjustment

when using DVI-D signal.

■ AUTO: Adjusts the phase, frequency and position automatically.

■ FREQ.: Adjusts the frequency of the signal.

■ PHASE: Adjusts the phase of the input signal.

■ H. POS.: Adjusts the horizontal position of the image.

■ V. POS.: Adjusts the vertical position of the image.

Setup

Runco CL-710

> Video S-Video Component Component HD RGB HD DVI-I

---------------------- Aspect Ratio Options

Setup

> Keystone Blue Image White Balance Reset Lamp Timer Background Color

Setup

The Setup menu is passcode protected and for the use by Runco personnel only. Many of the adjustments available in this section are intended for use by trained service personnel only. If you are having difficulty with one of these items, please contact your Runco Dealer for service.

All items below which are printed in italic are intended for service personnel only. Non-italic items can be modified by the projector owner.

The CL-710 has four memory settings for color temperature. Three of these settings are factory set to defalt as follows:

Te m p 1 -- 5400 kelvin Te m p 2 -- 6500 kelvin Te m p 3 -- 7500 kelvin

The Temp 4 memory is installer adjustable and can be used to create custom settings. A passcode must be entered in order to change this setting. There are nine adjustable "white balance" parameters available for the Temp 4 setting. Once the desired adjustments have been entered, selecting "store" will save these custom settings into the "Temp 4" memory position.

Keystone: Corrects the trapezoidal distortion as a result of the angle of projection (-12° ~ +12°). This can correct for up to +/12 degrees of offset.

Blue Image: This makes the red and green turn off.

5. Menu

Runco CL-710/ CL-710LT User’s Manual

White Balance: To adjust grey scale.

White Balance Red Gamma

Green Gamma

Adjust the Gamma Curve

Blue Gamma Red Gain Green Gain

Adjust High End

Blue Gain Red Offset Green Offset

Adjust Low End

Blue Offset Store

Reset Lamp Timer: Use this function to reset lamp usage counter. Reset only if you replace a new lamp.

Background Color: To adjust background color to blue or white.

5. Menu

6. Additional Information

Warning Message

■ It is normal for lamp to be darker when this unit

has been used for a period of time.

■ " Lamp life is expired ! Please change a new lamp.

And reset the lamp timer" message will be displayed for 30 seconds on the scr een if the lamp has operated for 950 hours.

■ " Please change the lamp, Lamp will exceed its

lifetime after (hours):" message will be displayed on the screen for 30 seconds for each time turning on, if the lamp has operated for 980 hours. And the number will count down continuously.

Runco CL-710/ CL-710LT User’s Manual

Lamp life is expired !

Please change new lamp

And reset the lamp timer

Please change the lamp !

Lamp will exceed its lifetime after (hours):

■ "Please change the lamp !" message will display on

the screen all the time and the PO WER LED will blink in orange and green sequentially if the lamp has operated for more than (1,000) hours.

■ The power will turn off automatically after 10

minutes.

Please change the lamp !

Replace the Lamp (Contact your Runco Dealer)

1. Loosen the screw of front lamp cover

3. Loosen the two screws of lamp module.

2. Take off the front lamp cover.

4. Pull out the lamp module horizontally.

5. Insert the new lamp module into this projector horizontally until it is securely in place.

6. Tighten the two screws of lamp module.

6. Additional Information

Runco CL-710/ CL-710LT User’s Manual

7. Put on the front lamp cover.

8. Tighten the screw of front lamp cover.

9. Turn on the power and go into the Set Up menu to reset the "Lamp Timer" item.

Troubleshooting

Problem Possible Cause Remedy

This unit does not turn on.

No picture The front lamp cover is not correctly

There is no power from power cable. Plug the power cord into the AC inlet on the

rear of this unit, and plug the power cord into to the power inlet.

The power switch is not turned on. Turn on the power switch.

Turn on this unit again within the cooling down procedure.

Front lamp cover is not attached well. Correctly attach the front lamp cover.

attached.

Wait this unit complete the cooling down procedure.

Correctly attach the front lamp cover.

This unit is not correctly connected to the input source device.

The input signal has not been correctly selected.

POWER LED or LAMP LED blinking. Please contact your Runco dealer for

Image is unstable The connection cables are not

connected to this unit.

Picture is blurred The projection lens is not correctly

focused.

This unit and the screen are not placed squarely. (90 degree)

Remote control does not work correctly

LAMP LED blink in red The front lamp cover is not correctly

The batteries are exhausted. Replace both batteries with new ones.

attached.

The cooling fan does not work well. Please contact your Runco dealer for

The temperature inside this unit is extremely high.

Check the connection.

Select the correct input signal with the input keys: Video, S-Video, Component, Component HD, RGB HD and DVI-I on the remote control.

assistance.

Correctly connect the cables to the appropriate terminals.

Adjust the focus of projection lens with the focus ring.

Adjust the projection angle and direction, and the height of this unit.

Correctly attach the front lamp cover.

assistance.

Check that the ventilation holes are not blocked.

POWER LED blink in orange and green sequentially

6. Additional Information

The lamp has exceed its specified usage hours.

The lamp has burned out. Replace the lamp with a new one.

Replace the lamp with a new one.

Runco CL-710/ CL-710LT User’s Manual

Specifications

CL-710/ CL-710LT Specifications

Projector Type: Digital Light Processing™ (DLP™), Single HD-2 DMD Chip Native Resolution: 1280 x 720, (16:9) Aspect Ratios: 4:3, Letterbox, 16:9, Anamorphic, Virtual Wide Video Standards: NTSC, PAL DTV Compatibility: 480p, 720p, 1080i Scan Frequency: Horizontal: 15-80 kHz

Vertical: 50-100 Hz

Picture Size (16:9 Screen): Recommended Width: 72-96 in.

Maximum Width: 200 in.

Throw Distance CL-710: 1.40 to 1.60/ CL-710LT: 1.85 to 2.40 (Factor x Screen Width): Please refer to page 11 to page 14.

Light Output: 1000 ANSI Lumens*

CSMS** Specifications: Home Theater Calibration: 489 ANSI Lumens

18.1 Foot-Lamberts (fL)

Contrast Ratio: 1800:1

CSMS** Contrast Ratio: 156:1

Lamp: 210W Lamp Life: 1000 hours @ 6500

Inputs: (1) Composite Video, (1) S-Video,

(1) RGB/Component (via BNC), (1) RCA Component Video, (1) DVI w/ HDCP, (1) RS-232

Memories: 21 memories 12V Output: Max .250 Amp, active when the projector is on Power Requirements: 100-240V AC, 50/60 Hz, 310 watts Operating Environment: 41°- 95° F, (5°- 35° C), 20%-80% Humidity (non-condensing) Dimensions (w/out feet): Width: 16.15 in. (410.16 mm),

Depth: 14.56 in. (369.71 mm), Height: Without feet 5.3 in. (134.62mm) with feet 5.8 in. (148.62 mm) Weight: 22 lbs. (10 kg) (includes lens)

Regulatory Approvals: UL, CSA, GS-TUV, CCIB, CB,

FCC, CE, VCCI and C-Tick

Kelvin

Limited Warranty: Projector:

labor from the date of delivery to the end user Lamp Warranty: (6) six months, which ever comes first.

(2) Two year parts and

1000 hours or

6. Additional Information

Runco CL-710/ CL-710LT User’s Manual

*ANSI Lumen specification:

This is the typical projector luminosity (brightness) specification found in most sales literature. This measurement is included in RUNCO literature to allow for direct comparison with other manufacturer's projectors. These measurements can be taken at 9,000 to 13,000 degree Kelvin to get expected performance data when the projector is used in professional, commercial, and industrial displays.

**CSMS Home Theater Calibration ANSI Lumen Specification:

These measurements are tak en fr om the projector as setup in a home theater environment. The projector is calibrated to ISF specifications including setting the color temperature to 6500 degree Kelvin, the standard for r eproducing video.

**CSMS Home Theater Calibration foot-Lambert (fL) Specification:

This is the unit of measurement used in commercial movie theaters to expr ess image br ightness. The Society of Motion Picture and Television Engineers (SMPTE) specifies 16 fL as the target image brightness for film-based projectors using an open gate (without film in the projector). More importantly, today SMPTE specifies 12 fL as the target image brightness in Digital Cinema theaters using DLP(tm) technology. The foot-Lambert is dependant on scr een size, screen gain, and projector light output.

All measurements are made at RUNCO to ANSI/NAPM IT7.228-1997 specifications using the Photo Research PR-650 SpectraColorimeter and Minolta LS-100 Light Meter, Video Essentials test DVD, and a Stewart Filmscreen StudioTech

130, 1.3 gain, 72-inch wide screen. The projector is calibrated to a color temperature of 6500

Kelvin and has a

minimum of 150 hours of usage.

6. Additional Information

Dimensions

Runco CL-710/ CL-710LT User’s Manual

Unit: in. (mm)

6. Additional Information

Runco CL-710/ CL-710LT User’s Manual

RS-232 Setup

Baud Rate: 115200 or 9600 Parity: None Data Bits: 8 Bits Stop Bits: 1 Bit Flow Control: Non e

RS-232C Control Codes

Code Function

X01 Power On X02 Power Off X03 Message On X04 Message Off X10 Menu (arrow key) X11 Enter (arrow key) X12 Exit (arrow key) X13 Up (arrow key) X14 Down (arrow key) X15 Left (arrow key) X16 Right (arrow key) X20 Switch to Composite input X21 Switch to S-Video input X22 Switch to Component input X23 Switch to D-Sub _PC input X24 Switch to YPBPR input X25 Switch to BNC_PC input X35 Anamorphic X36 Standard X37 Letter box X38 Virtual Wide X40 Load memory 1 settings X41 Load memory 2 settings X42 Load memory 3 settings X46 Load default of current source X47 Save memory 1 settings X48 Save memory 2 settings X49 Save memory 3 settings X55 Switch active source X56 Picture in picture display X57 Picture in picture display X60 Switch language - English X61 Switch language - French X62 Switch language - Spanish X85 PC Input - auto X90 Image orientation - floor front X91 Image orientation - ceiling front X92 Image orientation - floor rear X93 Image orientation - ceiling rear X94 Back light on X95 Back light off

PC Out Adapter

1. Connect D-Sub 9-pin female to RJ-11 adapter (not included) to Com port on PC.

2. Connect RJ-11 to Projector.

RJ-11 to D-Sub 9-pin (not included)

RS-232 For D-Sub 9-pin (not included)

D-Sub 9-pin female Details

2TxT 3RxD

D-Sub 9-pin female

5 Ground

1, 4, 6, 7, 8, 9 NC

War ning: During initial turn on and turn off of the projector, this unit will not accept RS-232 codes for 20 seconds.

RS-232 For RJ-11 (not included)

4-pin RJ-11 Details

2TxT 3RxD

1, 4 Ground

Yellow

Green

Black

Red

Yellow

NOTE:

1. All codes are in the ASCII format.

2. A carriage return is required after each command.

Green

345

Black

Red

6. Additional Information

RUMA-010100 rev 7-03

Runco International .2900 Faber Street .Union City, CA 94587 .ph (510) 324-7777 .fax (510) 324-9300 .www.runco.com

Runco CL-710LT, CL-710 User Manual 2

Specifications and Main Features

Frequently Asked Questions

User Manual

WARNING

Features

1. Overview

Projector Outlook

❚ Front / Upper Side

❚ Rear / Bottom Side

Controls and Functions

❚ Control Panel

Connector Panel

Remote Control

Remote Control

Projector

❚ Connect the Power Cord

2. Installation

Adjust the Lens Zoom/Focus ring

❚ Adjust the height

Installation For CL-710 (With 1.40 - 1.60 Lens)

Throw Distance Chart For CL-710 (With 1.40 - 1.60 Lens)

Installation For CL-710LT (With 1.85 - 2.40 Lens)

Throw Distance Chart For CL-710LT (With 1.85 - 2.40 Lens)

Connecting Video Inputs

❚ Video / S-Video / Component (Interlaced Video)

3. Connecting

Progressive Component (DTV Y/PB/PR)

❚ RGBHV (DTV RGB)

Connecting a Computer (DVI/ HDCP)

Turning on the Power

Zoom/ Focusing

Selecting Video Memory

4. Basic Operation

Selecting "ASPECT RATIO"

Direct Picture Adjust (Menu Bypass)

Setting Menu

Selecting Input Source

PIP/ PBP function

Turning off the Power

Using the Menu

Main Menu

5. Menu

Picture Quality Adjustments

Aspect Ratio

Options

Setup

Warning Message

Replace the Lamp (Contact your Runco Dealer)

6. Additional Information

Troubleshooting

Specifications

Dimensions

RS-232 Setup