Ruijie RG-S8600E Series Quick Installaion Manual

RG-S8600E Series Switches Quick Installation Guide V1.02

or commercial use of this document or any portion of this document, in any form or by any means, without the prior written consent of Ruijie Networks is prohibited.

Exemption Statement

This document is provided “as is”. The contents of this document are subject to change without any notice. Please obtain the latest information through the Ruijie Networks website. Ruijie Networks endeavors to ensure content accuracy and will not shoulder any responsibility for losses and damages caused due to content omissions, inaccuracies or errors.

Preface

Thank you for using our products. This manual will guide you through the installation of the device. This manual describes the functional and physical features and provides the device installation steps, hardware

troubleshooting, module technical specifications, and specifications and usage guidelines for cables and connectors.

Audience

It is intended for the users who have some experience in installing and maintaining network hardware. At the same time, it is assumed that the users are already familiar with the related terms and concepts.

Obtaining Technical Assistance

 Ruijie Networks Website: http://www.ruijienetworks.com/  Service Email: service_rj@ruijienetworks.com  Technical Support: http://www.ruijienetworks.com/service.aspx  Technical Support Hotline: +86-4008-111-000

Related Documents

Documents

Description

Configuration Guide

Describes network protocols and related mechanisms that supported by the product, with configuration examples.

Command Reference

Describes the related configuration commands, including command modes, parameter descriptions, usage guides, and related examples.

Symbol Conventions

Means reader take note. Notes contain helpful suggestions or references.

Means reader be careful. In this situation, you might do something that could result in equipment damage or loss of data.

1 Product Overview

Launched by Ruijie independently, RG-S8600E series next generation core switches adopt the Full Mesh/Clos architecture and support large buffer. RG-S8600E series support dual supervisor modules and power supply redundancy, which are available in three models, namely, RG-S8605E, RG-S8607E, RG-S8610E and RG-S8612E.

RG-S8605E adopts Full Mesh architecture and supports dual supervisor modules and provides 3 slots for service modules. RG-S8607E adopts Full Mesh architecture and supports dual supervisor modules and provides 5 slots for service modules. RG-S8610E adopts Clos architecture and supports dual supervisor modules and provides 8 slots for service modules. RG-S8612E adopts Clos architecture and supports dual supervisor modules and provides 8 slots for service modules.

2 Safety Precautions for Movement

RG-S8600E series is large and heavy. When you carry them, please pay attention to the following requirements:

 Unplug all power cords before you move the switch. Note: There may be more than one power cord.  Remove the power supply, fans and service modules to reduce the chassis weight before moving the switch for a long distance.  At least 4 people are needed to move the switch.  Keep balance when moving the switch by 4 people, and keep the pace with each other.  Grasp the handles on both sides of the chassis, not the power supply handle, fan handle or the rear panel handle. Those handles

are just used to install and remove corresponding parts, and cannot bear the whole switch weight.

 The whole switch weight may be higher than 80 kg during the movement.

To correctly move the RG-S8605E, refer to the Figure 2-1. For the RG-S8607E, refer to Figure 2-2. For the RG-S8610E, refer to Figure 2-3. And for RG-S8612E, refer to Figure 2-4.

Note that the following figures are just the schematic diagrams, do not insert the line card and power supply when moving the chassis to avoid the chassis weight increment or line card damage.

Figure 2-1 Moving the RG-S8605E Switch

Figure 2-2 Moving the RG-S8607E Switch

Figure 2-3 Moving the RG-S8610E Switch

Figure 2-4 Moving the RG-S8612E Switch

3 Preparations Before Installation

3.1 ESD Prevention

Precaution

To avoid the damages from static electricity to the internal parts of switches, do as follows:

 ESD prevention measures are taken in the sites where switches are installed.  Wear the antistatic wrist strap while installing various switch parts, especially when you may touch circuit boards with hands.  Grasp the edge of modules. Do not touch the parts or printed circuits directly.

Wearing the anti-static wrist strap

The antistatic wrist strap is shipped with RG-S8600E, which is used as follows:

1. Stretch out your hand into the antistatic wrist strap.

2. Lock the wrist strap and make sure that the metal part of the antistatic wrist strap is in good contact with skin.

3. Insert the antistatic wrist strap in the antistatic wrist strap jack of the switch chassis or clip on the grounding pole of the chassis. The antistatic wrist strap jack is located on the front panel of the chassis marked with yellow ESD.

4. The antistatic wrist strap is grounded well and the DC electric resistance between the body and the ground is in the range of 1 to 10 mega ohms.

Figure 3-1 ESD Prevention on RG-S8605E

Figure 3-2 ESD Prevention on RG-S8607E

Figure 3-3 ESD Prevention on RG-S8610E

Figure 3-4 ESD Prevention on RG-S8612E

3.2 Installation Site

RG-S8600E series must be used in the room. To ensure normal operation and a prolonged use life of the device, the installation site must meet the requirements of weight capacity, humidity , cleanness, EMI consideration, grounding system, power, and ventilation. See the Preparation before Installation chapter of RG-S8600E Series Switches Hardware Installation and Reference Guide for details.

3.3 Cabinet Mounting

Make sure the cabinet complies with the following conditions:

 Install the switch in a 19-inch cabinet in 4-port form hold.  Be sure the distance between two square hole strips, one on each side, is 465 mm.

Figure 3-4 19-inch Cabinet

 Be sure that the square hold strip is at least 180 mm far from the outboard front door and the door is at most 25 mm thick to

ensure a minimum available distance of 155 mm. The front door is at least 1000 mm far from the back door,

Figure 3-5 Cabinet Dimensions

 Be sure that the slide rail in the cabinet is enough to bear the weight of a RG-S8600E and its installation accessories.

 Be sure that the cabinet provides an earthing terminal for the switch to be grounded.  Be sure that the front and back doors of the cabinet have porosities greater than 50% for good ventilation and heat dissipation.

3.4 Installation Tools

Common Tools

Cross screwdriver, straight screwdriver, related electric and optical cables Bolts, diagonal pliers, straps

Special Tools

Anti-static glove, stripping pliers, crimping pliers, crimping pliers for the crystal head, wire cutter

Fiber Optic Cleaning Tools

Air-laid paper, optical fiber microscope

Meter

Multimeter, bit error rate tester (BERT), optical power meter

The tool kit is customer supplied.

3.5 Fiber Connection

Before connecting fiber cables, make sure the model of the optical transceiver and fiber type match the optical port. The transmit port on the local device should be connected to the receive port on the peer device and vice versa.

3.6 Unpacking

Goods Checklist

Chassis Carton

Device panels are installed and operational. Fans, screwdriver, anti-static wrist strap, yellow/green grounding wires, quick installation

guide, packing list

Module Carton

Modules, packing list, documentation

A normal delivery should contain the above mentioned items, which may differ from the actual delivery, depending on purchase contracts. Please check your goods carefully against the packing list or purchase contract. If you have any questions or there are

any errors, please contact your distributor.

4 Installing the Switch

4.1 Installation Flowchart

Figure 4-1 Installation Flowchart

4.2 Installing Slide Rails

When installing slide rails for the RG-S8600E, ensure that the plane to carry the chassis should be installed on the plane of delimiters of 1 RU, as shown in Figure 4-2.

Figure 4-2 Installing Slide Rails

Note: 1 and 2 represent 1 RU delimiters.

Before installing a slide rail, please verify that it is firm enough to bear the device weight and its installation accessories. The RG-S8600E series switch is available in three models with different heights. There are variable kinds of slide rails. The rail appearance and installation is subject to actual conditions. In order to keep the cabinet balanced, please install the slide rail to as low a position as possible in the cabinet if only one

RG-S8600E switch is installed. If you are mounting multiple device to the cabinet, mount the heaviest device in the lowest position of the cabinet first and proceed to mount the rest of the devices from bottom to top.

4.3 Installing the Air Filter (Optional)

Install air filters of the supervisor module, service module and switch fabric module on the RG-S8600E.

If an air filter is used for a long time, dust may block its air vent, weakening system ventilation. It is recommended you wash the air filter every three months.

Installing the Air Filters of the Supervisor Module and Service Module

(1) RG-S8605E Figure 4-3 Air Filter of the Supervisor Module and Service Module on RG-S8605E Switch

Note:

1 Captive screws

2 Air filter

 To install the air filter , follow these steps:

1) Insert the air filter along the slide rail. Note the direction identifier to ensure the correct direction.

2) Use a screwdriver to tighten the captive screws on the air filter.

Figure 4-4 Installing the Air Filter of the Supervisor Module and Service Module on RG-S8605E Switch

(2) RG-S8607E Figure 4-5 Air Filter of the Supervisor Module and Service Module on RG-S8607E Switch

Note:

1 Captive screws

2 Air filter

 To install the air filter , follow these steps:

1) Insert the air filter along the slide rail. Note the direction identifier to ensure the correct direction.

2) Use a screwdriver to tighten the captive screws on the air filter.

Figure 4-6 Installing the Air Filter of the Supervisor Module and Service Module on RG-S8607E Switch

(3) RG-S8610E

 To install the air filter , follow these steps:

1) Seat the air filter in the plastic cover and tighten screws.

2) Install the plastic cover before the air filter by pressing firmly the two buttons on the both sides of the plastic cover.

Figure 4-7 Installing the Air Filter of the Supervisor Module and Service Module on RG-S8610E Switch

Installing the Air Filters of the Switch Fabric Module

(1) RG-S8610E To install the air filter, follow these steps:

1) Seat the air filter in the plastic cover and tighten screws.

2) Install the plastic cover before the air filter by pressing firmly the two buttons on the both sides of the plastic cover.

Figure 4-8 Installing the Air Filter of the Switch Fabric Module on RG-S8610E Switch

Note:

1 Air filter

4.4 Installing Brackets

Wear the antistatic wrist strap and make sure the antistatic wrist strap is grounded well. The brackets of RG-S8605E, RG-S8607E, RG-S8610E and RG-S8612E are installed before delivery, as shown in figure 4-9,

4-10, 4-11 and 4-12. If you want to adjust the location of the bracket, see figure 4-13, 4-14 and 4-15. Location adjustment of brackets is not supported on the RG-S8612E.

 Install the bracket to the front chassis side

(1) RG-S8605E bracket (installed before delivery) Figure 4-9 Installing Brackets to Front Chassis Side

(2) RG-S8607E bracket (installed before delivery) Figure 4-10 Installing Brackets to Front Chassis Side

(3) RG-S8610E bracket (installed before delivery) Figure 4-11 Installing Bracket to Front Chassis Side

(4) RG-S8612E bracket (installed before delivery) Figure 4-12 Installing Bracket to Front Chassis Side

 Move the bracket backward

(1) RG-S8605E bracket

1. Remove the bracket from the front chassis side.

2. Install the bracket at a backward location, as shown in figure 4-13: Figure 4-13 RG-S8605E Bracket

(2) RG-S8607E bracket

1. Remove the bracket from the front chassis side.

2. Install the bracket at a backward location, as shown in figure 4-14: Figure 4-14 RG-S8607E Bracket

(3) RG-S8610E bracket

1. Remove the bracket from the front chassis side.

2. Install the bracket at a backward location, as shown in figure 4-15:

Figure 4-15 RG-S8610E Bracket

4.5 Mounting Cabling Rack

Make sure the antistatic wrist strap is grounded well and wear the antistatic wrist strap. The RG-S8610E cabling rack is mounted before delivery while RG-S8605E, RG-S8607E and RG-S8612E not. Please refer to

the following steps and figures for installation.

 Mount the cabling rack for RG-S8605E

1. Take out cabling racks.

2. There are three cabling racks on each side respectively. Pay attention to the direction to mount cabling racks, as shown in figure 4-16.

3. Align the screw holes on the cabling rack with those on the chassis and tighten the screws, as shown in figure 4-16.

Figure 4-16 Mounting the Cabling Rack for RG-S8605E

 Mount the cabling rack for RG-S8607E

1) Take out cabling racks.

2) There are five cabling racks on each side respectively. Pay attention to the direction to mount cabling racks, as shown in figure 4-17.

3) Align the screw holes on the cabling rack with those on the chassis and tighten the screws, as shown in figure 4-17.

Figure 4-17 Mounting the Cabling Rack for RG-S8607E

 Mount the cabling rack for RG-S8610E (mounted before delivery)

Figure 4-18 Mounting the Cabling Rack for RG-S8610E

 Mount the cabling rack for RG-S8612E (mounted before delivery)

Figure 4-19 Mounting the Cabling Rack for RG-S8612E

4.6 Mounting the Switch to a Cabinet

Precautions

Before mounting RG-S8600E series to the cabinet, first verify that the front and back brackets of the cabinet are at the right locations. If the bracket is too far forward, the front panel of the equipment may be too close to the front door, so that the front door cannot be

closed when network cables and fibers are connected. Usually, you should reserve at least 10 mm between the front panel of the switch and the front door of the cabinet. Before mounting the switch to a cabinet, you need to address the following conditions:

 Fasten the cabinet.  Insert various modules in the frame properly.  Remove any obstacle in the frame and the surrounding environment.  Prepare the equipment and move it to the place near the cabinet where you can handle it easily.

Five people is recommended to carry or lift the switch. One is responsible for directing and the other four carrying or lifting the switch.

Installation Steps

Measure the cabinet height and locate the position on the bracket for installing the slide rail. Then locate the position on the other bracket through the carrying plane and mark the locations. Install seven cage nuts on the marked square holes on each bracket as shown in figure 4-18.

Figure 4-20 Slide Rail Installation Positions

Place the switch on the slide rail, and drive it smoothly into the cabinet until the front bracket reaches the square hole strip. Align the installation holes on the bracket with the cage nuts on the square hole strip, and mount them with screws.

Figure 4-21 Mounting the Switch into the Cabinet

4.7 Connecting the System Ground

A good grounding system protects your switch against lightning strikes and interferences and ensures its normal operation and reliability.

Precautions

 The sectional area of the grounding wire should be determined according to the possible maximum current. Cables of good

conductor should be used.

 Do not use bare wire.  The grounding resistance for combined grounding should be less than 1Ω.

Connecting the System Ground

To connect the system ground, follow these steps:

1) Remove the two screws on the rear of the switch.

2) Attach the one end of the grounding wire to the switch with the two screws. Connect the other end of the grounding wire to the grounding wire of the cabinet.

Figure 4-22 Grounding Point on the Rear of the RG-S8605E Switch

Figure 4-23 Grounding Point on the Rear of the RG-S8607E Switch

Figure 4-24 Grounding Point on the Rear of the RG-S8610E Switch

Figure 4-25 Grounding Point on the Rear of the RG-S8612E Switch

To guarantee the security of the person and the device, the RG-N18000 must be well-grounded. The grounding resistance shall be less than 1Ω.

A service person shall check whether or not the socket-outlet from which the equipment is to be powered provides a connection the building protective earth. If not, the service person shall arrange for the installation of a protective earthing conductor from the separate protective earthing terminal to the protective earth wire in the building.

The socket-outlet shall be installed near the equipment and shall be easily. When installing the unit, always make the ground connection first and disconnect it last. The cross-sectional area of protective earthing conductor shall be at least 2.5 mm2 (12AWG).

4.8 Installing Power Supplies

The RG-S8600E series switches provide AC power supplies including RG-PA1600I, RG-PA600I, RG-PA1600I-P, RG-PA1600I-PL, and RG-PA3000I-PL as well as DC power supplies including RG-PD1600I and RG-PD600I. Before performing the following procedures, wear an anti-static wrist trap close to your kin and keep it grounded well.

The RG-S8605E power system provides two power supply slots, which support 1+1 redundancy. It is recommended users configure power supply redundancy. The power system also provides one PoE port.

The RG-S8607E power system provides four power supply slots, which support n+m redundancy. The power system also provides two PoE ports, which support 1+1 redundancy. It is recommended users configure power supply redundancy.

The RG-S8610E power system provides eight power supply slots, which support n+m redundancy. The power system also provides two PoE ports, which support 1+1 redundancy. It is recommended users configure power supply redundancy.

The RG-S8612E power system provides six power supply slots, which support n+m redundancy. By adopting the external PSE power frame, the power system also provides two PoE ports, which support 1+1 redundancy. It is recommended users configure power supply redundancy.

When RG-S8605E/ RG-S8607E/ RG-S8610E/ RG-S8612E is powered up by more than one source, the power must be in the same model.

The RG-PA1600I-P power system is applicable to RG-S8605E/ RG-S8607E/ RG-S8610E of versions earlier than V1.20 (V1.20 excluded).

The RG-PA1600I-PL/ RG-PA3000I-PL power system is applicable to RG-S8612E and RG-S8605E/ RG-S8607E/ RG-S8610E of versions later than V1.20 (V1.20 included).

If you want to carry or lift the power module, please hold the bottom of the module with your hand instead of carrying the module by the handle. Otherwise, the module may be damaged.

Before inserting or removing the power module, please verify whether the switch is well mounted. The switch is high, avoid switch tumble when you are inserting or removing the power module.

If you want to hot swap a power supply, please make sure that the interval between two operation is greater than 30s. Please do not touch the golden finger part of the power supply which is removed after power off in case that capacitor discharge

is not full.

 Install the AC power system

1. Loosen the captive screws on the fake panel covering the power slot at the rear of the chassis.

2. Insert the power module into the slot along the rail until the rear connector of the power module stays in good contact with the rear

panel.

3. Tighten the captive screws on the power module to fix it.

Figure 4-23 Installing Power Supplies

 Install the PoE power system

The PoE power system and the DC power system share the same installation steps with the AC power system.

The total power of power supplies of the RG-S8600E must be greater than the working power of the host. Otherwise, some modules may fail to start.

The host power is the summation of the power of all working modules, including the supervisor module, service module and fan. For the power of each module, please refer to

RG-S8600E Series Switches Hardware Installation and Reference Guide.

4.9 Installing Fans

The RG-S8600E provides a ventilation system: M05-FAN for RG-S8605E, M07-FAN for RG-S8607E, M10-FAN-R, M10-FAN-F for RG-S8610E and M12-FAN-R for RG-S8612E. Before the following procedures, wear an anti-static wrist trap close to your skin and have it properly grounded.

 Steps for installing the M05-FAN fan tray:

1) Install the fan tray into the fan slot in the rear panel of RG-S8605E. Note the direction identifier of the fan tray’s name to ensure the correct direction.