RuggON PX-501 User Manual
PX-501
User's Manual
©2015 RuggON Corporation. All rights reserved.
TRADEMARKS
RuggON logo is a trademark of RuggON Corporation, registered in the United States Patent and
Trademark Office and in other countries. Microsoft and the Windows logo are either registered
trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.
Microsoft products are licensed to OEMs by Microsoft Licensing, Inc., a wholly owned subsidiary
of Microsoft Corporation. The Bluetooth® word mark and logos are registered trademarks owned
by Bluetooth SIG, Inc. All other brand and product names are trademarks or registered trademarks
of their respective owners.
Images shown in this document may vary slightly from actual products at time of shipping.
Information in this manual is subject to change without notice.
i
Table of Contents
About This Manual
Related Information ......................................................................................1
Conventions ..................................................................................................1
Basic Safety Guidelines
Intended Use ................................................................................................2
Maintenance and Operation Overview .........................................................2
Safety ...........................................................................................................3
Electrical Hazards .........................................................................................3
Environmental ...............................................................................................3
Radio Transmissions ....................................................................................4
Cleaning and Servicing .................................................................................4
Regulatory and Certification .........................................................................4
Lithium Battery Safety Statement .................................................................5
Chapter 1. Introduction
About This Guide .......................................................................................... 7
Unpacking the Device ...................................................................................7
Technical Specifications ...............................................................................7
PX-501 Configuration Options ......................................................................9
Parts List .....................................................................................................10
Identifying the Device .................................................................................11
Identifying the Digitizer ...............................................................................15
Dimensions .................................................................................................16
Touch Screen Features ..............................................................................17
Chapter 2. Getting Started
First Time Use ............................................................................................18
Charging the Battery ...................................................................................18
Powering the Device On and Off ................................................................19
Installing the Micro SIM Card .....................................................................20
Removing the Micro SIM Card ...................................................................21
Installing the MicroSD Card ........................................................................22
Removing the MicroSD Card ......................................................................23
ii
Using the Digitizer ......................................................................................24
Removing the Protective Film from the Display ..........................................25
Chapter 3. Operation
Opening the I/O Compartment Cover .........................................................26
Closing the I/O Compartment Cover ..........................................................27
Connecting to External Cabling ..................................................................28
Handstrap, Carrying Handle and Shoulder Strap .......................................30
Installing the Standard Battery ...................................................................34
Removing the Standard Battery .................................................................35
Connecting to a Wireless Network .............................................................36
Chapter 4. Using BIOS Setup Utility
When to Use the BIOS Setup Utility ...........................................................38
Accessing the BIOS Setup Utility ...............................................................38
Installation an Operating System ................................................................39
BIOS Passwords ........................................................................................42
EC and BIOS ..............................................................................................44
Chapter 5. Using the DashON Utility
Overview .....................................................................................................49
Chapter 6. Troubleshooting
Troubleshoot the Wi-Fi Connection ............................................................62
Troubleshoot Operating the Computer .......................................................63
Call Product Support ..................................................................................63
Chapter 7. Maintenance
Cleaning the Device ...................................................................................64
Returning the Device ..................................................................................64
Contacting RuggON ...................................................................................64
1
About This Manual
The PX-501 User’s Manual provides instruction for qualified personnel to follow when setting up a
new PX-501 device.
This document is intended for use by qualified personnel to compliment the training and expertise,
not to replace it.
Related Information
Current information and manuals are available for download at the following website:
http://www.ruggon.com
Conventions
Bolded or underlined text is used to emphasize the designated information.
A Note is used to provide additional information for the device or settings.
A Caution is used to warn against potential hazards or to caution against unsafe practices.
A Warning is used to identify immediate hazards for property damage, injury or death.
2
Basic Safety Guidelines
The following safety guidelines are intended to help protect the user from injury and prevent
damage to the hardware.
Do not place anything on the AC adapters power cable and make sure the cable is not
located where it can be tripped over or stepped on.
Do not cover the AC adaptor as it reduces the cooling
Do not use the AC adapter while it is inside the carrying case.
Use only the AC adapter, power cord, and batteries that are approved for use with the device.
Use of another type of battery or AC adapter may cause risk of fire or explosion.
If you use an extension cable with the AC adapter, ensure that the total ampere rating of
all products plugged in to the extension cable does not exceed the ampere rating of the
extension cable.
If the device is moved between environments with very different temperature and/ or humidity
ranges, condensation may form on or within the device. Avoid damaging the device by
allowing sufficient time for the moisture to evaporate before using the device.
When disconnecting cables, pull on the connector or on its strain relief loop, not on the
cable itself. When pulling out or plugging in the connector, keep it evenly aligned to prevent
bending the connector pins.
Intended Use
The PX-501 rugged tablet is equipped with multi-functional terminals for stationary and mobile
applications in industrial environments such as logistics, warehousing, fleet management,
manufacturing and the automotive industry.
Read the safety guidelines thoroughly before starting any servicing on the device. Read the
guidelines before powering up the device, and keep this document for later use.
The operator is solely responsible for any damage resulting from unauthorized modifications to the
device.
Unintended Application Use
The device is not designed for use in life-support systems or critical safety/security systems where
system malfunction can lead to the direct or indirect endangerment of human life. The operator is
fully responsible for using the device in these situations.
Maintenance and Operation Overview
The PX-501 is designed and manufactured according to strict controls and following the stated
safety regulations. The following list identifies incorrect operating uses of the PX-501. Incorrect
use of the PX-501 can lead to hardware damage, safety issues and possible risk to personnel
health:
The PX-501 is under operation by untrained personnel;
The PX-501 is not maintained as recommended;
The PX-501 is not used as intended.
3
Safety
To prevent injury and damage, read the following safety guidelines prior to operating the
device. The manufacturer assumes no liability for any and all damages arising from misuse or
noncompliance with these guidelines.
Electrical Hazards
Cleaning/Servicing: Power Off the PX-501
Disconnect the PX-501 from power before cleaning or servicing it.
Power Adapter
Contact an authorized service personnel for repairs to the power pack. In the event of a blown
fuse after replacing the fuse, contact an authorized service personnel to avoid electrical shock.
Use only Supplied Power Cables
RuggON power cables meet industrial requirements for low-temperature flexibility, UV resistance,
and oil resistance. Use only supplied power cables from RuggON.
If other power cables are used, the following may apply:
The operator is solely responsible for the resulting damage;
All RuggON warranties are void.
Environmental Hazards
Do not use the PX-501 in locations near/with flammable gases or vapor.
The use of electrical equipment in explosive environments can be dangerous.
Turn off the device when near a gas station, fuel depot, chemical plant or a place where
blasting operations take place.
Environmental
Ambient Temperature
The PX-501 operates on the basis of a passive cooling concept which internal waste heat is
released via the housing surface and requires fresh airflow in the environment.
Operating the PX-501 with no fresh cooling air may cause overheating and damage to the
device.
The operating environment should not be enclosed to prevent the cool air being heated by
the heat waste from the device.
Connecting and Disconnecting External Devices
To prevent the considerable damage, the PX-501 and the external device should be disconnected
from power when connecting/disconnecting excluding USB devices.
4
Only Use Authorized Accessories
Only use the supplied cables, power packs and other accessories that have been tested and
approved by RuggON. Contact your local distributor for further information.
Radio Transmissions
Permitted Transmission Power
Follow the national regulations for the maximum permitted transmission power.
The operator is solely responsible for this type of operation.
Radio Frequency Limited Locations
Considering the radio frequency limitation in hospitals and aircraft, the PX-501 can only be
installed with permission.
Industrial computers may affect the function of implanted medical devices such as pacemakers
and may cause malfunction.
Cleaning and Servicing
Disconnect the PX-501 from power before cleaning or servicing.
Never clean the PX-501 with compressed air, a pressure washer or a vacuum cleaner.
If necessary, clean the housing of the PX-501 with a damp cloth.
Clean the touch-screen with a nonabrasive cloth.
Regulatory and Certification
FCC
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own expense.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
5
Consult the dealer or an experienced radio / TV technician for help.
Any changes or modications not expressly approved by the grantee of this device could void the user’s
authority to operate the equipment.
This device is operation in 5.15 – 5.25GHz frequency range, then restricted in indoor use only, Outdoor
operations in the 5.15 – 5.25GHz is prohibit.
This device is slave equipment; the device is not radar detection and not ad-hoc operation in the DFS
band.
Labeling Requirements
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
RF Exposure Information (SAR)
This device meets the government’s requirements for exposure to radio waves. This device is
designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF)
energy set by the Federal Communications Commission of the U.S. Government.
The exposure standard employs a unit of measurement known as the Specific Absorption Rate,
or SAR. The SAR limit set by the FCC is 1.6 W/kg. Tests for SAR are conducted using standard
operating positions accepted by the FCC with the EUT transmitting at the specified power level in
different channels.
The highest SAR value for the device as reported to the FCC is 0.57 W/kg when placed next to the
body.
CE Marking
This product has passed the CE test for environmental specifications when shielded cables are
used for external wiring. We recommend the use of shielded cables. Please contact your local
representative for ordering information.
This product has passed the CE test for environmental specifications. Test conditions for passing
included the equipment being operated within an industrial enclosure. In order to protect the
product from being damaged by ESD (Electrostatic Discharge) and EMI leakage, we strongly
recommend the use of CE-compliant industrial enclosure products.
R&TTE
This device complies with the essential requirements of the R&TTE Directive 1999/5/EC.
CB
This device complies with the IEC 60950-1:2005+A1.
Lithium Battery Safety Statement
Lithium battery inside. Danger of explosion if battery is incorrectly replaced. Replace only with same or
equivalent type recommended by battery manufacturer.
6
7
Introduction
Chapter 1. Introduction
The PX-501 is a rugged device equipped with 802.11, Bluetooth and GNSS for wireless data
communications.
The PX-501 is a rugged 10.1” tablet computer capable of 1920 x 1200 resolution.
The PX-501 supports the following operating systems:
Windows
®
Embedded 8.1 Industry 64bits
Windows
®
Embedded Standard 7 64bits
Windows
®
7 Professional 64bits
Windows
®
Embedded Standard 8 64bits
About This Guide
The PX-501 User Manual provides instruction for qualified personnel to use as a guide for setup of
the device. This document is not intended to replace the training and expertise of the end-user.
Unpacking the Device
Before you begin the installation or configuration process make sure to inspect all components
and accessories. Contact your representative if there are any missing or damaged items. See
“Contacting RuggON” on page 64.
Technical Specifications
Table 1. Technical Specications
Item Description
Display 10.1-inch LED Backlight, 1920 (W) x 1200 (H) WUXGA
Touch screen 10-point capacitive touch screen with digitizer
Brightness 1000 nits
CPU Intel Core i5-4300U vPro 1.9 GHz
Operating System
(Optional)
Windows
®
Embedded 8.1 Industry 64bits
Windows
®
Embedded Standard 7 64bits
Windows
®
7 Professional 64bits
Windows
®
Embedded Standard 8 64bits
RAM DDR3L@1600 MHz 4 GB RAM (optional: 8 GB)
Storage mSATA SSD 120 GB (optional: 240 GB)
Battery
Standard hot swappable battery: 10.8V, 4500mAh, Li-polymer
Extended hot swappable battery: 10.8V, 9000 mAh, Li-polymer
(optional)
Power Supply AC 100V ~ 240V, 50~60Hz input; 19VDC@3.42A, 65W
Dimensions (W x H x L) 280 mm (11”) x 23 mm (0.9”) x 195 mm (7.7”)
Weight 1.36 kg (3 lbs)
8
Introduction
Item Description
Wireless
WLAN Wi-Fi IEEE 802.11 a/b/g/n/ac
Bluetooth Bluetooth V4.0
WWAN (Optional) Option for 3.5G or 4G LTE
Sensor
Sensor Gyroscope, G Sensor, E-compass, Light Sensor
I/O
Docking Connector 12-pin
DC-IN Jack x1
Micro SIM Card Slot x1
MicroSD Slot x1
Audio Jack x1; headphone / microphone combo
USB 3.0 x1; type A
RS-232 x1
Micro HDMI x1
Ethernet x1
Security
TPM TPM 1.2
BIOS On/Off for I/Os YES
Data Collection
Camera
Front: 2.0 Mega-Pixels camera
Rear: 5.0 Mega-Pixels camera with LED auxiliary light and
Auto-focus
GNSS YES
NFC Optional
Barcode Reader Optional
Magnetic Stripe Reader Optional
Smart Card Reader Optional
9
Introduction
Item Description
Rugged Specifications
Drop 153 cm (5 feet), 26 drops on plywood
MIL-STD 810G
Vibration (MIL-STD-810G Method 514.6 Category 4,
Fig 514.6C-1, Fig 514.6C-2, Fig 514.6C-3)
Drop (MIL-STD-810G Method 516.6 Procedure IV)
Mechanical shock
(MIL-STD-810G Method 516.6 Procedure I, Procedure V)
Operation and storage temperature
(MIL-STD-810G Method 501.5 and 502.5)
Humidity MIL-STD-810G Method 507.5 Humidity Procedure II
Aggravated Cycles (Fig 507.5-7)
IP rating IP65
Operating Temperature
Range
-20°C (-4°F) to 60°C (140°F)
Storage Temperature
Range
-30°C (-22°F) to 70°C (158°F)
Humidity 5-95% without condensation
PX-501 Configuration Options
The following options are available for the PX-501:
NFC module
Barcode reader
Smart card reader
High capacity battery
3.5G or 4G LTE
10
Introduction
Parts List
The PX-501 is shipped with the following items. All other accessories are sold and ordered
separately. For help, contact your local RuggON sales representative. See “Contacting RuggON”
on page 64.
fn
f1
f2
fn
PX-501
Power Adapter Digitizer 2-Point Carrying Handle
2-Point Shoulder Strap 4-Point Handstrap
Hitch D-rings
(Attaching straps)
11
Introduction
Identifying the Device
Overview
fn
f1
f2
fn
1
5
3
4
6
2
Figure 1. Overview
Table 2. Overview
No Item Description
1 Left view See “Side View” on page 14 for further information.
2 Front view See “Front View” on page 12 for further information.
3 Rear view See “Rear View” on page 15 for further information.
4 Right view See “Side View” on page 14 for further information.
5 Rubber bumpers
Easy to grip rubber bumpers enable the rugged tablet to withstand
shocks and drop for use in demanding environments.
6 Bottom view See “Bottom View” on page 13 for further information.
12
Introduction
Front View
fn
f1
f2
fn
13
12
14
3
4
5
6
1
8 791011
2
Figure 2. Front View
Table 3. Front View
No Item Description
1 Front camera 2.0 Mega-Pixels camera.
2 Touch screen 5-point capacitive touch.
3 Barcode trigger If barcode scanner is installed, press to scan.
4 Battery LED Display battery status, see “LED Status” on page 13.
5 Wi-Fi LED The Wi-Fi LED lights to indicate Wi-Fi is enabled.
6 FN LED The FN LED lights when the function switch on.
7 Home key Windows® 8 home key.
8 Volume + Volume increase.
9 Volume - Volume decrease.
10 Power key Turns the PX-501 on or off.
11 Power LED The power LED lights when the device is on.
12 F2 key Programmable function key.
13 F1 key Programmable function key.
14 FN key Programmable function key.
13
Introduction
LED Status
Table 4. LED Status
Item Status Description
Power
Green: On Power on
Off Power off
Battery
Green: On Fully charged
Amber: On Charging
Amber:
Blinking
Low power < 15%
Off Not charging / no battery
FN
Blue: On FN function switch on
Blue: Off FN function switch off
Wi-Fi
Blue: On Wi-Fi on
Blue: Off Wi-Fi off
Bottom View
1
2 3
Figure 3. Bottom View
Table 5. Bottom View
No Item Description
1 Docking connector 12 pin connector for docking onto a station.
2 Kensington lock Lock the PX-501 to a stationary object for security.
3 Pass-through Dual pass-through for WLAN, GNSS and WWAN.
14
Introduction
Side View
Right view
ON
OFF
3.0
SDSIM
Left view
9
12
13
3
2
4
1
10
11
5
8
7
6
Figure 4. Side Views
Table 6. Side View
No Item Description
1 Micro HDMI Connect HDMI devices to the PX-501.
2 MicroSD slot Insert microSD card in to the slot.
3
Left I/O
compartment
cover
Open to access the left I/O ports.
4 Tether hole Digitizer can be tethered to it.
5 Battery switch Switch to ON to provide power from the backup battery.
6 Micro SIM slot Insert micro SIM card for 3G or 4G LTE communication function.
7 USB 3.0 Connect USB devices to the PX-501.
8 Audio jack Connect a 3.5 mm jack for a headphone or external speakers.
9 Ethernet Connect the PX-501 to an Ethernet (RJ-45) cable.
10 DC-IN jack Insert power connector to charge battery.
11 RS-232 Connect the PX-501 to a serial device.
12 DC-IN cover Open to access the DC-IN jack.
13
Right I/O
compartment
cover
Open to access the right I/O port.
15
Introduction
Rear View
7 6
55
4
321
Figure 5. Rear View
Table 7. Rear View
No Item Description
1 Battery To install a battery, an external battery is optional.
2 Rear camera 5.0 Mega-Pixels camera with LED auxiliary light.
3 Barcode reader For installing a barcode reader. (Optional)
4 Fan Embedded fan for cooling.
5 Securing holes
Secure the bumpers and the D-rings for the handstrap and shoulder
strap.
6 Expansion bay Remove the cover to find the expansion accessory connector.
7 Digitizer holder Place digitizer here.
Identifying the Digitizer
You can use the digitizer to control your PX-501 as with a mouse or keyboard.
The digitizer is not waterproof. Take care not to soak it or dip it in water.
Tip
Click Button
Figure 6. Digitizer View
16
Introduction
Dimensions
The following image lists the device dimensions without add-ons (mm/inches).
28 / 11
19.5 / 7.7
fn
f1
f2
fn
280 / 11
195 / 7.7
Figure 7. Front View Dimensions
2.3 / 0.9
23 / 0.9
Figure 8. Side View Dimensions
17
Introduction
Touch Screen Features
Always use the point of the digitizer for clicking or making strokes on the touch screen.
Never use an actual pen, pencil, or sharp/abrasive object on the touch screen.
The digitizer is used as if it were a pen or pencil. Touch the screen with the tip of the digitizer then
remove the digitizer from the screen.
After each use, replace the digitizer in the digitizer holder for proper care and to preserve the life of
the digitizer.
Using a digitizer is similar to moving the mouse pointer then left-clicking icons on a desktop
computer screen.
The following actions are available through the use of the digitizer:
Open applications
Choose commands in menu
Select options in dialog box or drop-down menu
Drag the scroll bar
Drag across the text to select content
Place the cursor in a text box before typing
A right click is generated by tapping the mouse icon in the system tray. After tapping, the mouse
icon highlights the right button of the icon in red. The next touch screen tap is treated as a right
click. The mouse icon returns to the left button highlighted in red so subsequent taps are treated
as left clicks.
A digitizer replacement kit is available.
To prevent damage or malfunction, always dry the touch screen when wet.
Loading...