Rugged Outback ELX4-60 User Manual

ELX4-60

User’s Guide (CCTV Mo nitor User)

v 1.0

FCC Compliance Statement

Caution : Any changes or modifications in construction of this device which are not expressly approved

the party responsible for compliance could void the user's authority to operate the equipment.
NOTE : This equipment has b een tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications, However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

CAUTION

Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Dispose of used batteries according to the general recommendations against the environmental pollution.

Important Notice

1. Do not place heavy objects on the top of the ELX4-60.

2. ELX4-60 is for indoor use. It is not weatherproof. Use ELX4-60 with referring to its environmental
specifications (Temperature & Humidity). To clean the ELX4-60, gently wipe the outsi de with a clean dry
cloth.

3. Be sure to use a DC adapter that is provided by Rugged CCTV Connecting ELX4-60 directly to an AC
current will cause electric damages to ELX4-60.

4. Be careful not to drop the ELX4-60. Physical shocks may harm the product. In addition, be sure the
ELX4-60 is secured after installation.

5. If ELX4-60 does not operate properly, please contact the closest Rugged CCTV distributor for after
sales service. Tampering or disassembling the product will void the warranty.

6. Security surveillance laws may differ for each country. Therefore, please contact the local region first
to avoid any surveillance law violations.

ELX4-60 TABLE OF CONTENTS

OVERIVEW ..................................................................................................................................................................7

1. Introduction.......................................................................................................................................................7

2. Product Description.......................................................................................................................................9

2.1. Front Panel .................................................................................................................................................9

2.2. Rear Panel ............................................................................................................................................... 10

2.3. Installation Summary.............................................................................................................................11

Basic Configuration .............................................................................................................................................12

3. Monitoring ....................................................................................................................................................... 12

3.1. Viewing basic screen (quad-split).................................................................................................... 12

3.2. Viewing single full screen ...................................................................................................................12

3.3. Viewing multi screen.............................................................................................................................12

3.4. Viewing all channels with sequence mode...................................................................................13

3.5. Viewing an alarm triggered channel................................................................................................14

3.6. Viewing images with Digital Zoom ...................................................................................................14

3.7. Viewing with connected PTZ .............................................................................................................14

3.8. Using Relay.............................................................................................................................................16

3.9. Using Screen Lock................................................................................................................................16

4. Playback...........................................................................................................................................................16

4.1. Playback via various mode................................................................................................................16

4.1.1. Playback via basic screen (full screen).................................................................................16

4.1.2. Playback via split screen............................................................................................................17

4.1.3. Playback with Digital Zoom.......................................................................................................17

4.1.4. Various playback modes ............................................................................................................17

4.2. Using Search Mode ..............................................................................................................................18

4.3. Copy / Backup / Delete Data Manager .......................................................................................... 19

4.3.1. Copy Image .................................................................................................................................... 19

4.3.2. Backup Manager ...........................................................................................................................20

4.3.3. Delete Data .....................................................................................................................................21

5. Configuration ................................................................................................................................................. 21

4 2003.05.21 (v 1.0) Rugged CCTV

TABLE OF CONTENTS ELX4-60

5.1. Quick Setup .............................................................................................................................................21

5.1.1. Date/Time ........................................................................................................................................21

5.1.2. Recording ........................................................................................................................................23

5.2. Camera – Analog Camera Channels (Ch. 1 ~ Ch. 4)............................................................... 25

5.3. Normal Rec. - Analog Camera Channels (Ch. 1 ~ Ch. 4).......................................................28

5.4. Alarm Rec. – Analog Camera Channels (Ch. 1 ~ Ch. 4).........................................................31

5.5. Relay.......................................................................................................................................................... 34

5.6. Monitor.......................................................................................................................................................35

5.7. System.......................................................................................................................................................36

5.7.1. Audio .................................................................................................................................................36

5.7.2. Text .................................................................................................................................................... 37

5.7.3. Time Schedule............................................................................................................................... 39

5.7.4. Special Time...................................................................................................................................40

5.7.5. Security............................................................................................................................................41

5.7.6. Disk Setup.......................................................................................................................................42

5.7.7. Network............................................................................................................................................43

5.7.8. Serial Setup .................................................................................................................................... 49

5.7.9. Miscellaneous ................................................................................................................................50

5.8. Utility .......................................................................................................................................................... 52

5.8.1. Disk Manager .................................................................................................................................53

Advanced Configuration...................................................................................................................................55

6. Using IP Cam.................................................................................................................................................55

6.1. Activating IP Cam menus ...................................................................................................................55

6.2. Camera Setting – IP Camera Channels (Ch. 5 ~ Ch. 16) ....................................................... 56

6.2.1. Configuration .................................................................................................................................. 56

6.2.2. Local IP Cam List.........................................................................................................................58

6.3. Normal Rec. – IP Camera Channels (Ch. 5 ~ Ch. 16) .............................................................59

6.4. Alarm Rec. - IP Cam Channel (Ch. 5 ~ Ch. 16).......................................................................... 60

7. Connecting External Device...................................................................................................................61

7.1. Using Text Device..................................................................................................................................61

7.1.1. Setting at Text menu.................................................................................................................... 61

7.1.2. Setting at Serial Setup’s RS232 menu..................................................................................62

Rugged CCTV 2003.05.21 (v 1.0) 5

ELX4-60 TABLE OF CONTENTS

7.1.3. Setting at Alarm Rec. menu ......................................................................................................62

7.1.4. Setting at Normal Rec. menu ...................................................................................................63

7.2. Using Keyboard......................................................................................................................................64

7.2.1. Setting at Serial Setup’s RS232 menu..................................................................................64

7.2.2. Setting at Serial Setup’s PTZ menu ....................................................................................... 64

APPENDIX ..............................................................................................................................................................65

Appendix #1 Technical Specification .......................................................................................................66

Appendix #2 Utilizing IP Addresses on Local Network ...................................................................69

#2.1 Introduction..................................................................................................................................................69

#2.2 IP constr uction and Network class...................................................................................................... 69

#2.3 C-class Network ........................................................................................................................................70

6 2003.05.21 (v 1.0) Rugged CCTV

OVERVIEW ELX4-60

OVERIVEW

1. Introduction

What is ELX4-60?

ELX4-60 supports 4 analog video channels and 12 IP video channels simultaneously. Video, Audio, and
Text Event-Logs are digitized and stored on two internal hard-drives. Using a ‘Proprietary Wavelet
Algorithm,’ average file size is 1-5KB while still maintaining clarity high enough for facial-recognition.
In addition, Wa velet -compressed images are impossible to manipulate.

Due to our proprietary Wavelet Algorithm, the ELX4-60 processes analog vid eo into crisp, clear, and
court-admissible pictures that are up to 500% smaller than comparable JPEG images. With this efficiency ,
ELX4-60 records over 30 days on a 200GB hard disk drive when recording 4 channels at the speed of
10ips per channel. ELX4-60 also allows users to record and playback audio for one channel.

Setting-up ELX4-60 is as easy as setting up a VCR. ELX4-60 starts to record as soon as power is
supplied and CCTV cameras are connected. ELX4-60 offers an easy setup, as well as advanced menus.
With ‘Quick Setup’, ELX4-60 can be setup and begin recording in as little as 5 minutes. The default
settings offer quality and efficiency without the hassle of confusing menus .

Equipped with (3) IEEE 1394 ports (Fire-Wire) and (3) USB ports, ELX4-60 can expand its recording
capacity to up to 4TB easily. For easy backup, Windows (FAT32) formatted HDD is compatible with
ELX4-60. Simply back up the desired data and connect the HDD to your PC to review critical images.

Rugged CCTV 2003.05.21 (v 1.0) 7

ELX4-60 OVERVIEW

Key features

- Expandable up to 16 channels (4 analog video channels + 12 IP video channels)

- 1 channel audio recording & playback

- Recording, Playback, Back-up images and Networking at the same time (Quadplex)

- Total 120 ips recording speed (Analogue video 60ips + IP video 60ips)

- Total 120 ips display speed (Max 60ips over Network)

- Displaying live and recorded images on PC as well as CCTV Monitor

- Built-in hardware Quad Splitter for analog video

- Built-in software multiplexer for all 16 live monitoring channels

- (1 / 4 / 9 / 13 / 16Ch Mode on CCTV Monitor as well as PC)

- Maximum 4TB storage capacity (IEEE 1394 for external HDD)

- Various configuration with recording and play back conditions

- Intelligent file system for managing event triggered video data

- ATM/POS transaction information text recording and search with corresponding video

(Text search function is supported through DVR Manager program)

- 4 pairs of sensor inputs and alarm outputs

- Built-in hardware motion detection with search function (64-division comparison)

- Back-up with IEEE 1394(FiWi).

- PTZ Control (Preset support) via RS 232 and RS 485 /RS422

- User-friendly 32bit True-colored Graphic OSD Menu

- Dynamic IP (DHCP, Floating IP) support (when xDSL and Cable Modem are used)

- Wavelet compression: 1-5KB (Average file size with standard image quality)

- Embedded Linux OS for excellent stability and reliability

- IR remote controller (User controls PTZ with remote controller)

- DVR Manager (User Interface of PC) is to be listed with 16 units of ELX4-60 on a program

(256chnnels (16 sets of ELX4-60 x 16channel) are controllable through a program)

8 2003.05.21 (v 1.0) Rugged CCTV

OVERVIEW ELX4-60

2. Product Description

2.1. Front Panel

(1) Remote
Controller Receiver

(1) Remote Controller Receiver

(2) Channel
Selection Button

(3) LED

(4) Function
selection button

(5) Direction/Replay
Button

(2) Channel Select ion Button

- To select video input channel in monitoring and playback mode
(3) LED

- PWR : Displays power status. When lit, power is supplied.

- NET : Displays the status of Ethernet connection and rate of communication. When blinking, data

being transmitted or received over the Ethernet.

- REC : Displays image recording status. The rate of blinking indicates the speed of recording. (i.e.

When blinking rapidly, ELX4-60 is recording at a high rate; when blinking slower, the ELX4-60 is
recording at a lower rate.)

- PLAY : Displays playback status . The rate of blinking indicates the speed of playback. (i.e. When

blinking rapidly, ELX4-60 is playing back at a high rate; when blinking slower, the ELX4-60 is
playing back at a lower rate.)

- ALARM 1~4
(4) Function selection button

- SEQ : To select Sequencing Mode. ELX4-60 will automatically display all connected channels in

successive order.

- MULTI : To select the multi-channel display (4 -9-16-13 divided screen) .

- SELECT : To select video channel for PTZ control.

- ZOOM : To activate the digital zoom (single channel mode only).

- SEARCH/RELAY : To search the recorded image in Playback mode or to toggle the Relay On/Off

function in Monitoring mode

Rugged CCTV 2003.05.21 (v 1.0) 9

ELX4-60 OVERVIEW

(4) Video

(5) Direction/Replaying Button

- MENU : To set PTZ and access Configuration menu .

- ENTER : To enter and confirm the selected menu.

- HELP : To change the image information display (Date, Transfer speed, etc).

- EXIT/LOCK : To exit form the selected menu or lock current screen.

- Arrow key : Replay function or to move inside the Configuration menu.

2.2. Rear Panel

(1) Serial Port
& DIO

(2) Audio port

(3) Video
Output

Input

(5) Ethernet

(6) Power

(1) Serial Port & DIO

- Serial : RS232 9Pin D-Sub Connector & RS232/422/485 terminal block

- Sensor In : 4 sensor inputs

- Relay Out : 4 Alarm Relay outputs
(2) Audio port

- 1 audio input & 1 output
(3) Video Output

- 1 monitor output & 1 VCR output
(4) Video Input

- 4 video inputs
(5) Ethernet
(6) Power

10 2003.05.21 (v 1.0) Rugged CCTV

OVERVIEW ELX4-60

2.3. Installation Summary

- Connect Camera

- Connect Monitor

- Connect Ethernet.

(This is optional to view image on remote location or to add IP channel to ELX4-60 )

- Connect Audio

- Connect Power & Run

Rugged CCTV 2003.05.21 (v 1.0) 11

ELX4-60 BASIC CONFIGURATION

Basic Configuration

3. Monitoring

Once power is supplied to ELX4 -60, default quad-split monitoring mode (analog channels 1~4) will be
displayed. Th e following steps apply for all ELX4 -60’s monitoring menus.

<Button control>

- Press the [MULTI] button on the front panel of ELX4-60 to change the split configuration (4, 9, 16, 13).

- For sequence mode, press the [SEQ] button on the front panel of ELX4-60. To configure the sequential
cycle, access the “Monitor ” tab of Configuration Menu.

3.1. Viewing basic screen
(quad-split)

- Insert AC cord’s plug in a wall outlet and

turn the power switch “On.”

- LED is on and ELX4-60 starts booting.

- After start-up, the basic screen (quad-split) is

displayed.
* If user password is set, a dialogue box for
entering the password will appear.

3.2. Viewing single full screen

- Press the desired channel number button on

the front panel of ELX4-60.

- When selecting channels between channel 10

and 16, press the [+10] button first, then the
second number.

- To return to the multi-view screen, press the

[MULTI] button.

3.3. Viewing multi screen

- Press the [MULTI] button to view several channels simultaneously.

- To change the split screen configuration, press the [MULTI] button. 4, 9, 16, or 13 split screens will be

displayed.

- In quad-split mode, images of channels 1 to 4 are displayed. Channels 1 to 9 are displayed in 9-split

mode, channels 1 to 16 in 16-split mode, and channels 1 to 13 in 13-split mode.

12 2003.05.21 (v 1.0) Rugged CCTV

BASIC CONFIGURATION ELX4-60

3.4. Viewing all channels with sequence mode

- All channels can be viewed in successive order automatically using the [SEQ] button.

- Press the [MENU] button on the front panel to set-up the sequential cycle. (The default value is 3

seconds per channel for display.)

- Select “ Monitor” tab of Configuration menu.

- Move to “Configuration” below “Monitor” using the down arrow button on ELX4-60 front panel.

- Press the [ENTER] button to enter the menu.

- Select “Seq. Switching(sec)” and press the [ENTER] button.

- Set any value between 1 and 60 seconds.

- Then press the [SEQ] button from any viewer mode (except 16/13-split screen).

<Note>

Sequence mode can run only when connected and activated cameras are more than split screen.
With single full screen mode, activated cameras should be two or more. With quad -split screen mode,
there should be five or more activated cameras . With 9-split screen mode, there should be ten or more
activated cameras . (SEQUENCE MODE ONLY SUPPORTS 4- AND 9- SPLIT SCREENS). Channel
order cannot be changed. For example, with quad-split screen, Ch. 1/2/3/4 are displayed and then
Ch.5/6/7/8 are displayed.

- To end sequence function, press the [SEQ] button.

Rugged CCTV 2003.05.21 (v 1.0) 13

ELX4-60 BASIC CONFIGURATION

3.5. Viewing an alarm triggered channel

- When an alarm is triggered, the related channel will pop-up full screen automatically.

- Set ‘Alarm Pop-up Screen’ function to “On” in “Configuration” under the “Monitor” tab, and set the

display duration in “Pop-up Hold (sec) ”

- If more than one channel is triggered by an alarm, the related channels will be displayed simultaneously

in a split -screen. In order to move current screen, press any button.

3.6. Viewing images with Digital Zoom

- In Single Full Screen mode, live and recorded images can be expanded using the Digital Zoom feature.

- To enable the digital zoom, press the [ZOOM] button.

- Digital Zoom will expand the image to twice its normal size.

- Default location of the digital zoom is in the center of screen. The zoom box can be moved each 10th

step to left and right and 4th step up and down.

- To move the zoom box, use the [Arrow] button.

- To cancel the zoom box, press the [ZOOM] button once more.

3.7. Viewing with connected PTZ

- Pan/Tilt/Zoom (PTZ) devices can be controlled through the ELX4-60

when a PTZ device is connected and properly configured under “Serial
Setup.”

- While in Monitor mode, press the [SELECT] button.

- Channel selection icon will be displayed.

- Move the icon to the channel to control with the [Arrow] button.

- Press the [MENU] button.

- PTZ menu (Pan/Tilt, Zoom/Focus, Load Preset, Save Preset) will appear.

- Press the [ENTER] button after selecting the desired function.

14 2003.05.21 (v 1.0) Rugged CCTV

BASIC CONFIGURATION ELX4-60

Pan/Tilt Control

To control Pan and Tilt during live image monitoring mode.

- Press the [SELECT] button. Move the “Select” icon to the desired channel.

- Press the [MENU] button.

- Select ‘Pan/Tilt’ from the PTZ Menu.

- Control pan and tilt function using the up, down, left and right arrows.

Zoom/Focus Control

To control Zoom and Focus during live image monitoring mode.

- Press the [SELECT] button. Move the “Select” icon to the desired channel.

- Press the [MENU] button.

- Select ‘Zoom/Focus’ from the PTZ Menu.

- Control zoom and focus functions using the up, down, left and right arrows of front panel.

Load Preset

To load preset for dome camera during live monitoring mode.

- Press the [SELECT] button. Move the “Select” icon to the desired channel.

- Press the [MENU] button.

- Select ‘Load Preset ’ from the PTZ M enu.

- Press number button for desired preset on the front panel.

Save Preset

To set a new preset point for dome camera during live monitoring mode

- Move dome camera to the desired position using the ‘Pan /Tilt’ and ‘Zoom/Focus’ menus.

- Press the [SELECT] button.

- Press the [MENU] button.

- Select ‘Save Preset ’ from the PTZ Menu.

- Designate a number for the preset position by pressing a number button on the front panel.

Rugged CCTV 2003.05.21 (v 1.0) 15

ELX4-60 BASIC CONFIGURATION

3.8. Using Relay

- To set relay on/off. ( ELX4 -60 supports four relay outputs.)

- Press the [SEARCH/RELAY] button.

- The icon of “Relay On ” shows.

- Press the relay number button between 1 and 4, and then the related relay out signal will be transmitted.

- In order to set relay off, press the [SEARCH/RELAY] button again.

- Then “Relay On” sh ows because relay keeps being set as on.

- Press the [SEARCH/RELAY] button again, and then the icon of “Relay Off” will show.

- Press the relay a number button to set off.

3.9. Using Screen Lock

- To set screen lock.

- For this function, user password should be set at first.

- If pressing the [EXIT/LOCK] button for 2~3 seconds, lock mode will run with showing “Screen

Locked” message.

- If lock mode runs, any function button will not be operated.

- In order to cancel lock mode, user password should be entered.

4. Playback

To replay recorded images in full screen or quad split screen modes.

4.1. Playback via various mode

4.1.1. Playback via basic screen (full screen)

- Press the Play [] button during monitoring mode.

- Play [] button will begin playback of the last 1minute, 45 seconds of recorded video at 1X speed.

<Note>

When pressing the play button in multi-monitoring mode, channel 1 is always the channel displayed.
More specifically, images recorded on Channel 1 during the last 30 seconds are always displayed.
However pressing the playback button in single-channel monitoring mode, will display the selected
channel. To display another channel, press the corresponding number button on the front of ELX4-60.

16 2003.05.21 (v 1.0) Rugged CCTV

BASIC CONFIGURATION ELX4-60

4.1.2. Playback via split screen

- Press the [MULTI] button during basic (single-channel) playback mode.

- Channels 1 to 4 will be displayed in the quad-split screen.

- To display a single channel, press the corresponding number button on the front of the ELX4-60.

4.1.3. Playback with Digital Zoom

- Press the [ZOOM] butto n during the basic (single-channel) playback mode.

- Digital Zoom will expand the image to twice its normal size.

- Default location of the digital zoom is in the center of screen. The zoom box can be moved each 10th

step to left and right and 4th step up and down.

- To move the zoom box, use the [Arrow] button.

- To cancel the zoom box, press the [ZOOM] button once more.

4.1.4. Various playback modes

 (PLAY) : To begin playback mode and replay at 1x speed. After pressing PAUSE (), PLAY will

advance recorded images frame by frame.

-  (STOP) : To stop replaying

-  (PAUSE) : To pause replaying

- (FAST FORWARD) : Each press of the button will increase playback speed gradually (x1, x2, x4,

x8, x16)

-  (FAST REWIND) : Each press of the button will increase playback speed gradually (x1, x2, x4, x8,

x16)

- STEP FORWARD : Pressing [, PLAY] or [ , FAST FORWARD] button from PAUSE status, will

replay image frame by frame. In order to go back to normal playback mode, press [, STOP] button then
press [, PLAY] or [, FAST FORWARD] button.

- STEP REWIND : Pressing [ , FAST REWIND] button from PAUSE status, will replay image frame

by frame. In order to go back to normal playback mode, press [, STOP] button then press [, PLAY] or
[, FAST FORWARD] button.

Rugged CCTV 2003.05.21 (v 1.0) 17

ELX4-60 BASIC CONFIGURATION

4.2. Using Search Mode

Search Mode is used to search and play specific data directly during playback mode. Data can be
searched by specific Time and Date or by the Event Log browser.

Button control

- Press the [SEARCH] button during playback mode.

- Search for data by entering Date/Time or by selecting an event from the Event Log browser.

- Press the [ENTER] button after entering the desired Date/Time or selecting Event from log.

- The selected images will begin to playback .

- To exit from search mode, press the [EXIT] button.

<Note> Using Log Browser

1. To move to the previous/next page, press the "Left" or "Right" buttons.

2. To move to previous log entry, press the "Up" button.

3. To move to next log entry, press the "Down" button.

18 2003.05.21 (v 1.0) Rugged CCTV

BASIC CONFIGURATION ELX4-60

4.3. Copy / Backup / Delete Data Manager

To copy/backup/delete the recorded data. This menu is activated during playback mode.

- Press the [SELECT] button and [MENU] button in Playback mode.

4.3.1. Copy Image

To copy a specific data with USB memory stick.

Seconds

To des ignate copy range between 1 and 60 seconds.

Select Disk

Select copy disk.

Rugged CCTV 2003.05.21 (v 1.0) 19

ELX4-60 BASIC CONFIGURATION

4.3.2. Backup Manager

Start Date & Time / End Date & Time

To designate backup range.

Select Disk

To select which storage will be used as backup device. To change the disk status, use the “Disk Manager”
menu under the “System” tab.

<Note>

Backup Manager does not support USB devices. Backup Man ager will ONLY work with devices
connected through IEEE1394 / FireWire ports.

20 2003.05.21 (v 1.0) Rugged CCTV

BASIC CONFIGURATION ELX4-60

4.3.3. Delete Data

To delete a specific file range from the current recording HDD. This menu does not affect backup disk.
The beginning of the range is always the beginning of the recording on the HDD.

5. Configuration

5.1. Quick Setup

There are three menus for recording setup; Quick Setup, Normal Recording, Alarm Recording menu
in Configuration Menu. Quick Setup is the easiest set-up, activating all four analog cameras to record
with the same settings and conditions . Normal recording is the standard recording settings and can be
customized based on time and channel. Alarm recording is the recording schedule based on alarm
conditions (Motion Detection, Sensors, etc.) Also, Quick Setup has time setting menu.

5.1.1. Date/Time

When ELX4-60 is manufactured in factory, time zone will be set as “GMT + 9:00”.
Set the time to local time zone.
Changing ELX4 -60 time may cause time conflict with recorded images. In this case, it is strongly
recommended to re-format the hard drives after making changes.

Button control

- Press [MENU] button on ELX4-60 front panel.

- Move to “Quick Setup ” menu (First tab on the Configuration menu).

- Move to “Date/Time” below “Quick Setup ” using downward arrow button on ELX4-60 front panel.

- Press the [ENTER] button on ELX4-60 front panel.

- Set time. (The following picture will be displayed when setting time menu)

- In order to access each menu, press [ENTER] button after selecting it with upward/downward
arrow button on ELX4-60 front panel.

Rugged CCTV 2003.05.21 (v 1.0) 21

Time Zone

ELX4-60 BASIC CONFIGURATION

Set the time zone using the left/right arrow button on ELX4-60 front panel. Every time you press
left/right arrow button, time zone will change. Select the desired time zone. (To move to the previous
menu, press [EXIT] button on ELX4-60 front panel.)

Daylight Saving

The Daylight Savings option is linked to Time Zone. Daylight Savings is only activated for time zones
that use Daylight Savings. For example, selecting GMT – 7:00 Arizona will disable the option for
Daylight Savings because Daylight Savings is not used in Arizona. This menu is linked with “Time Zone”
menu. Namely, if selecting daylight saving area in time zone, this menu will be activated. Oppositely if
selected time zone is not enforced, it will not be. It is based on MS Windows. So this menu is for setting
whether you apply ON/OFF (with left/right arrow button on ELX4-60 front panel) in daylight saving area.

Time Format

Set the time format between “MM/DD/YYYY” and “YYYY/MM/DD ” using the left/right arrow button
on ELX4-60 front panel.

Date/Time

Set date and time. To move from Month to Day to Year/Hour to Minute, use the left/right arrow buttons.
To select each month, each day, etc, use the up/down arrow buttons.

Apply Date/Time

Press this button to confirm the above settings. Windows will pop -up warning of the possibility of time

22 2003.05.21 (v 1.0) Rugged CCTV