Rudd 21VR30DV User Manual

G

2"

1/2"

RELIEF

VALVE

COLD

WATER

CONN.

ADJUSTS TO PITCHES

OF UP TO 5/12"

WATER CONNECTIONS

ALL 3/4" N.P.T.

H

D

E

C

F

A
B

24" MIN.

0" MIN.

WALL

CLEARANCE

Warrior DVThe Direct Vent Gas Water Heater for Manufactured Housing

®

Available in 30, 40 and 50 Gallon Models



5-Year Limited Tank Warranty*1-Year Limited Parts Warranty*

No external vented door is required

•

All combustion air comes from outside the

•

home
Provides maximum design freedom since it

•

can be placed anywhere within the home
Hot water outlet located at top

•

Factory installed temperature and pressure

•

Peizo ignitor – easy light pilot

•

Certified for manufactured (HUD) and

•

modular construction
Anode rod equalizes aggressive water

•

action
Cold water inlet – side connection allows

•

for fast, economical hook-up
relief valve – side location.
Exclusive Rheemglas®tank lining resists

•

corrosion and prolongs tank life
Field convertable controls for natural gas or

•

*See Residential Warranty Information Brochure for

complete warranty information.

LP operation
Meets or exceeds National Appliance

•

Energy Conservation Act (NAECA)
requirements

ESCRIPTION FEATURES ROUGHING IN DIMENSIONS (SHOWN IN INCHES) ENERGY INFORMATION

D

T

Y

GAL. THOUS. BTU/HR. G.P.H. 90° RISE DEL. G.P.H. VENT HT. DIAM. CONN. SIZE VENT SZ. T&P CONN. WT. FACTOR OPER. COSTS

P
E

AP. MODEL NUMBER NAT/ LP NAT./LP NAT./ LP AB C DEFGH(LBS) NAT./LP NAT. LP

C

30 21VR30DV 30 30.3 51 57 57 17-3/4 14-1/2 3551-1/2 20 110 0.61 $299 $503

T
A

40 21VR40DV 30 30.3 60 57-1/2 57-1/2 19-3/4 14-1/2 3551-1/2 20 125 0.59 $309 $520

L
L

50 21VR50DV 32 32.3 67 57 57 21-3/4 14-1/2 3551-1/2 20 150 0.58 $315 $529

GAS INPUT IN RECOVERY IN FIRST HOUR HT.TO TANK GAS VENT JACK SIDE WATER SHIP. ENERGY AVG. ANN.

Energy Factor and Average Annual Operating
Costs based on D.O.E. (Department of Energy)
test procedures. D.O.E.national average fuel rate
natural gas $1.218/therm; LP $1.87/gallon

HT.TO ROOF HT.TO

.

These units are designed
to meet or exceed ANSI
(American National
Standards Institute)
requirements and have
been tested according to
D.O.E. test procedures and
meet or exceed the energy
efficiency requirements of
NAECA, ASHRAE standard
90, ICC Code and all state
energy efficiency perfor­mance criteria for energy
consuming appliances.

Before purchasing this
appliance, read important
energy cost and efficiency
information available from
your supplier.

In keeping with its policy of continuous progress and product improvement, Rheem reserves the right to make changes without notice.

Rheem Water Heaters • 101 Bell Road, Montgomery, Alabama 36117-4305 • www.rheem.com

P R INTE D I N U . S .A 0 7 /08 WP F O RM N O . 1 0 2 GW- 9 Re v. 4

Adjustable Roof Jack Vent

Design allows adjustment to roof
pitches of up to 5/12". Four roof jacks
available to accommodate roof
thickness of 12" up to 95".

Direct Combustion
Air Inlet

Air is drawn directly into combustion
chamber through air inlet fixed to
base; 1/2" screen for rodent
protection.

ROOF JACKS

12" Non Adjustable & Air Inlet AP12032E
15-32" Adjustable & Air Inlet AP12032B
30-60" Adjustable & Air Inlet AP12032C
48-95" Adjustable & Air Inlet AP12032D

AIR INLETS

6" Non Adjustable AP12019B
11-22" Adustable AP12017B

EXTENSION PIPE KIT

Roof Jack Extension Pipe Kit AP12021

• Roof jack and air inlet must be ordered separately with
30, 40 and 50 gallon direct vent models and must be in
accordance with instructions furnished with the heater.
No other roof jack or air inlet assemblies are approved
for installation with this heater. Clamps and secure
strapping are packed in water heater carton.

THE WARRIOR DV IS U.L. CERTIFIED FOR

MANUFACTURED HOME USE, MEETS

ANSI STANDARDS FOR MODULAR HOME

CONSTRUCTION, AND COMPLIES WITH HUD
SAFETY AND CONSTRUCTION STANDARDS.

*FOUR ROOF

JACKS AVAILABLE
TO ACCOMMODATE
ROOF THICKNESS OF 12" UP TO 95"