Ruby Tech 2000/MKII User Manual

9902155

SANITATION LISTED

COMMERCIAL
POWERED FOOD
PREPARING
EQUIPMENT

CONFORM TO ANSI / NSF STD8

USER MANUAL

Ruby 2000/MKII

JUICE EXTRACTOR

PLEASE READ THIS MANUAL BEFORE OPERATING YOUR JUICER.

IMPORTANT

This unit is fitted with a safety switch which will prevent it accidently
being switched on while the lid is not on securely.

It is important to remember that if you cannot turn your juicer on,
please make sure that the lid has been fitted correctly.

All other operating instructions remain unchanged and it is important
that the user reads and understands them before operating the juicer.

Ruby 2000/MKII

JUICE EXTRACTOR

ASSEMBLY & CARE

:

Please read through this user manual carefully
before operating your new juicer.

Congratulations on purchasing the finest commercial grade
centrifugal juicer available. If looked after, the Ruby 2000/
MKII will provide you with customer satisfaction and good
returns for years to come. It is therefore imperative that you
familiarize yourself and your staff with the operation of this
juicer for safe and trouble free juicing.

We stand by our product therefore we are offering a 24 months
parts 12 months labour warranty.

These instructions must be followed and the juicer used
correctly. Maintenance must be carried out only by an authorized
technician. Failure to comply will result in the voidance
of warranty.

Keep this manual on file for further reference.

INSTRUCTIONS

:

Follow these instructions for safe, trouble free juicing.

STEP 1 . Upon unpacking your

juicer perform an initial inspection.
Make sure that the juicer is free of
damage that may have occurred
during transport, and that all parts
have been supplied.

Your box should contain the
following items;

• 1 x Ruby 2000 juicer

• 1 x Exhaust Tube

• 1 x 7/8 combination spanner

• 1 x Pusher / Plunger

• 1 x Users Manual

STEP 2. It is now time to look

for a place to set up your juicer.

• We recommend a minimum

working area approximately

500mm x 500mm in size

• You will also require a

power supply.

10amp

• The Ruby 2000 has 8 positions

for the juice spout and

2 for the exhaust tube, making

it suitable for most locations.

.

220~240V,

in place. Loosen this with your
spanner removing it along with the
strainer, blade and collection pan.
Locate the juice spout in the hole
that best suits your workspace.
Replace the strainer making sure
it locks into position over the 2
pins. Replace the blade, turning it
till it locks into place. Replace the

7/8 nut, tightening it firmly with

your spanner.

STEP

4 . Replace the lid and

fasten the lock latches on each
side. These latches are adjustable.
To tighten the latches turn the
hooks clockwise and to loosen
them do the opposite.

Do not over tighten the latches,
this will stretch or brake them.

STEP

5 . Plug in your juicer,

making sure step 3 has been
completed and the juicer is
switched off. You may now turn
on the juicer. Your juicer should
run smoothly.

STEP

6 . You are now ready to

make your first juice.

STEP

3 . Once you have found

a suitable location for your juicer
remove the top cover. You should

see the 7/8 locking nut that holds

the cutting blade and strainer

Ruby 2000/MKII

PARTS &
ASSEMBLy

A. Plunger/Pusher

B. Top Cover

C. Side Latch

D. 7/8 Nut

E. Cutter Blade

F. Basket/Strainer

G. Exhaust Pins

H. Tube/Exhaust

I. Pan Collector

J. Frame

K. Side Latche Anchor

L. Shroud

M. Drive Plate

N. Grub/Set screw

O. Motor

P. Base

Q. Strain Releif

R. Switch

S. Spacers

T. Rubber Feet

U. Spanner/Wrench

V. Power Lead

:

Juice Extractor

G.

H.

K.

N.

U.

A.

B.

C.

D.

E.

F.

I.

J.

M.

L.

O.

P.

R.

NOTE: Those parts indicated as M, N and

O can not be replaced or adjusted except
at the factory or by ringing the service
department for more information.

Q.

V.

S.

T.

CLEANING INSTRUCTIONS

:

Because fruits and vegetables contain natural substances that will build
up and stain your filter if left unclean, it is important that you follow this
set of cleaning instructions.

STEP 1 . Find a suitable container
that you can soak your filter in. It is
a good idea if you obtain one solely
for this purpose. Container size about
33cm in diameter and 23cm deep
is ideal.

STEP 2 . In about 4 Liters of hot

water dissolve 250grams (1 cup) of

commercial dishwashing powder.

In Australia we recommend
Chlordex.

(Order Code DET10: Available
from your local supplier)

STEP 3 . Rinse your filter under a

stream of water removing as much
of the pulp stuck to it as possible.
Place the filter directly into the
solution. It is important that you do

not scrub or brush the filter with any
abrasive cleaning aids. Place the filter
in the solution and allow it to soak
over night.

STEP 4 . In the morning thoroughly
wash the filter with regular detergent
and rinse.

STEP 5 . Follow these instructions
after each day of business to avoid
build up on your filter.

Note you may also clean the
blade, nut and collection pan in
this solution to remove build up
and staining.

Points to consider.

* Do not leave your filter in an area

where it can be damaged.

* Do not wash it along with your

pots, pans or other cooking
utensils. This can often damage
your filter.

* Do not scrub or brush the filter

with any abrasive cleaning aids

* If your filter is not cleaned and

maintained your juicer will not
function properly.

* If during the day you are stopping

to empty pulp from within the
filter frequently, your cleaning
procedures must be reviewed.
If you experience continuous
clogging contact an authorized
technician for service.

* Do not leave water or juice on

the top of the motor hub. Over
a period of time this liquid can
make its way into the bearings
damaging them.

MAINTENANCE :

* You should have your machine serviced at least once a year. Like most things if

you have your juicer serviced regularly, expensive repairs may be avoided.

* Your blade over time will wear dull. The blade can be re-sharpened for better yield.

* Your juicer should only be serviced by an authorized technician.

* Do not alter your juicer in any way or form. This will void any warranty.

* Bearings do not require lubrication.

Ruby 2000/MKII

Juice Extractor

TROUBLE

SHOOTING TABLE:

SYMPTOM

JUICER WON’T

START

JUICER STARTS

SLOWLY

PULP IS NOT
BEING EXPELLED

EXCESSIVE

VIBRATION

MOTOR STALLS

LOOSE COVER

POSSIBLE CAUSE

No electricity

Lid Not On Correctly

Improper electric current

Clogged holes in basket

7/8 nut has become
loose Filter clogged

Overloading of feed

Side latches have not
been adjusted correctly.

WHAT TO DO

Check your power point to see
if it is working. Check that the
cord is not broken

Check to see if lid is on correctly

Make sure there is a sufficient
current supply.

Make sure that you follow the
cleaning instructions specified
in this manual.

Check that the central lock­ing nut is not missing or loose.
Tighten with wrench supplied.

Reduce pressure on the pusher
as you feed the product into
your machine.

You can adjust your side latch­es by rotating the hooks either
clockwise to tighten or counter­clockwise to loosen. Do not
over tighten the latches this may
stretch or damage them.

SERVING SUGGESTIONS:

Over the past 30 years this juicer has been developed to extract juice from
almost all types of fruits and vegetables. The unique design of the cutter
blade and the large strainer basket insures a maximum amount of juice from
your product.

Below is a list of a few serving suggestions;

ORANGE: PINEAPPLE
ROCKMELON
CARROTS
APPLE
MANGO
PAW PAW

APPLE: CARROT
HONEYDEW
PINEAPPLE
LEMON
(Ginger as additive)

CARROT: CELERY
TOTATO
CUCUMBER
GINGER
BEATROOT

WATERMELON: STRAWBERRY
MINT
ORANGE

PINEAPPLE: MINT
APPLE, LEMON,GINGER
GINGER

BEFORE CONTACTING OUR OFFICE REFER TO
YOUR USER MANUAL AND CHECK

• your appliance is correctly installed

• you are familiar with its normal operation

• you have read the trouble shooting guide at the back of the book

IF YOU NEED SERVICE OR ASSISTANCE PLEASE CONTACT US AT

NUTRIFASTER AUSTRALIA PTY LTD.

UNIT 7, 62-66 NEWTON ROAD
WETHERILL PARK, NSW 2164

Tel: [phone]
Fax: [phone]

Email: [e-mail]

www.nutrifaster.com.au

LIMITED BACK TO BASE WARRANTY

Nutrifaster Australia PTY LTD, warrants the workmanship and all parts against
defects for a period of 24 months and 12 months labour from the date of original
purchase for use. Warranty only applied to original purchaser and is not transferable.

This warranty is null and void if the unit and/or its components therein have been
damaged or tampered with by improper handling, use or unauthorised repair. In all
cases of damage during transport, for repair, a claim must be filled with the shipping
carrier by the purchaser. In all events the manufacturer agrees to repair or replace
defective parts but never to exceed the purchase price paid. As this warranty is lim­ited , Nutrifaster Australia PTY LTD liability for cosequential and incidental damages
is expressly disclaimed and shall not exceed the purchase price paid.

For a copy of our full term and conditions of trade please contact our office.

NUTRIFASTER AUSTRALIA PTY LTD

| www.nutrifaster.com.au | [e-mail]

Unit 7, 62-66 Newton ROAD, WETHERILL PARK, NSW 2164 | tel: [phone] | fax: [phone]