Ruby RC-1001 User Manual

Publication date: March, 2011

Revision A2

i

User's Manual

Web Smart 10/100Base-TX to 100Base-FX

Media Converter

Release 1.04

Publication date: March, 2011

Revision A2

ii

Table of Contents

C

AUTION........................................................................................................................................... IV

ELECTRONIC EMISSION NOTICES..................................................................................................... IV

1. INTRODUCTION ............................................................................................................ 1

1-1. OVERVIEW .................................................................................................................................. 1

1-2. FEATURES ................................................................................................................................... 1

1-3. CHECKLIST ................................................................................................................................. 2

1-4. VIEW OF THE CONVERTER .......................................................................................................... 3

2. INSTALLATION .............................................................................................................. 4

2-1. CABLE AND HARDWARE INSTALLATION ..................................................................................... 4

3. OPERATION OF WEB-BASED MANAGEMENT ...................................................... 5

3-1. WEB MANAGEMENT HOME OVERVIEW ..................................................................................... 6

3-2. THE FUNCTION TREE IN WEB MANAGEMENT ............................................................................ 8

3-3. LOCAL SETTING ......................................................................................................................... 9

3-3-1. IP Configuration .............................................................................................................. 9

3-3-2. Password Setting ............................................................................................................ 11

3-3-3. Converter Configuration ............................................................................................... 12

3-3-4. Port Configuration......................................................................................................... 14

3-3-5. MIB Counter .................................................................................................................. 16

3-3-6. VLAN .............................................................................................................................. 17

3-3-6-1. V LAN Group ........................................................................................................................... 17

3-3-6-2. V LA N P er Port Setting ........................................................................................................... 19

3-3-7. Q-in-Q ............................................................................................................................. 21

3-4. REMOTE SETTING .................................................................................................................... 23

3-4-1. TS-1000 Functions ......................................................................................................... 23

3-4-1-1. TS -1000 Setting ....................................................................................................................... 23

3-4-1-2. Loopback Test ......................................................................................................................... 25

3-4-1-3. Remote Device Reset ............................................................................................................... 26

3-4-1-4. Remote Port Information ....................................................................................................... 27

3-4-1-5. Remote Port Setting ................................................................................................................ 27

3-4-2. 802.3ah Function ............................................................................................................ 28

3-4-2-1. 802.3ah Con figuration ............................................................................................................ 28

3-4-2-2. Loopback Test ......................................................................................................................... 29

3-4-2-3. 802.3ah Status .......................................................................................................................... 30

3-5. TOOLS ....................................................................................................................................... 31

3-5-1. System Reboot ................................................................................................................ 31

3-5-2. Save and Restore ............................................................................................................ 32

3-5-3. Firmware Upgrade ........................................................................................................ 33

3-5-4. Logout ............................................................................................................................. 33

4. MAINTENANCE .............................................................................................................34

4-1. RESOLVING NO LINK CONDITIONS ........................................................................................... 34

4-2. Q&A ........................................................................................................................................ 34

APPENDIX A TECHNICAL SPECIFICATIONS ...........................................................35

Publication date: March, 2011

Revision A2

iii

Revision History

Release Date Revision

0.96 12/04/2009

A

1

1.01 10/7/2010

A

1

1.02 10/29/2010

A

1

1.04 03/03/2011

A

2

Publication date: March, 2011

Revision A2

iv

Caution

Circuit devices are sensitive to static electricity, which can damage their delicate
electronics. Dr y weather conditions or walking acr oss a carpeted floor may cause
you to acquire a static electrical charge.

To protect your device, always:

 Touch the metal chassis of your computer to ground the static electrical

charge before you pick up the circuit device.

 Pick up the device by holding it on the left and right edges only.

Electronic Emission Notices

Federal Communications Commission (FCC) Statement

This equipment has been tested and found to comply with the FCC Part 15, Subpart
B, Class A.
CISPR 22:A1:2000+A2:2002;ICES-003:2004, Class A

European Community (CE) Electromagnetic Compatibility Directive

This equipment has been tested and found to comply with the protection
requirements of European Emission Standard EN55022 and EN55024.

EMI

EN55022:2006 Class A
EN61000-3-2:2006
EN61000-3-3:1995+A1:2001+A2/2005+A1/2001+A2/2005

EMS

EN55024/1998+A1:2001+A2:2003

IEC61000-4-2:2001
IEC61000-4-3:2002+A1:2002
IEC61000-4-4:1995+A1:2000+A2:2001
IEC61000-4-5:2001
IEC61000-4-6:2003
IEC61000-4-8:2001
IEC61000-4-11:2001

Publication date: March, 2011

Revision A2

v

About this user’s manual

In this user’s manual, it wi ll not o nly tell you how to install and conn ec t your network
system but configur e and m onitor the W eb Smart MEDIA CONVERTER through the
built-in web by E ther net po rts step- by-ste p. Man y expl anations in detail of hard wa re
and software functions ar e sho wn as we ll as the ex am ples of the oper atio n for web­based interface.

Overview of this user’s manual

 Chapter 1 “Introduction” describes the features of Web Smart MEDIA

CONVERTER

 Chapter 2 “Installation”
 Chapter 3 “Operation of Web-based Management”
 Chapter 4 “Maintenance”
 Appendix A

Publication date: March, 2011

Revision A2

1

1. Introduction

1-1. Overview

The Converter is des igned to m ake conver sion betwee n 10/100Base- TX and
100Base-FX Fast Ethernet. With Web-based management, the network
administrator can logon the converter to monitor, configure and control the activity of
each port. In addition, the converter implements bandwidth rating management
capability via the intel ligent software. T he over all net work managem ent is enhance d,
and the network efficiency is also improved to accommodate and deliver high
bandwidth applications.

1-2. Features

The Web Smart MEDIA CONVERTER provides the following features for
users to perform system network administration.

Management

• Supports Web UI for management

• Supports OAM for remote management via TS-1000

• Supports OAM for remote management via IEEE802.3ah

• Supports Ingress/Egress Rate Limitation

• Supports Link Loss Carry Forward Function

• Supports per Port MIB Counters

• Supports IEEE802.1Q VLAN

• Supports Q-in-Q (Double-Tag) VLAN

• Supports one 10/100Base-TX Fast Ethernet UTP port and one 100Base-FX FE
Fiber port

• Supports 802.3x flow control for full-duplex ports and backpressure for half-duplex
ports

• Supports comprehensive types of fiber with different distances and connections,
including SC/Bidi/LC and so on

• Supports auto mode on the TP port

• Supports jumbo frame 9KB

• RoHS Compliance

• On-board firmware can be updated via HTTP web function.

• The converter allows administrator to reboot system from management station.

• Dying Gasp function can send out a signal when DC power down is detected.

Publication date: March, 2011

Revision A2

2

1-3. Checklist

Before you start installing the converter, please verify that the package contains the

following:

 Web Smart Media Converter
 AC-DC Power adapter
 This User's Manual(CD)

Please notify your sales representative immediately if any of the aforementioned

items is missing or damaged.

Model

Model Description

RC-1001 Web Smart 10/100Base-T to 100Base-FX Media Converter
RC-1001A Web Smart 10/100Base-T to SFP Media Converter

Publication date: March, 2011

Revision A2

3

1-4. View of the Converter

RC-1001 RC-1001A

Fig. 1-1 WEB SMART MEDIA CONVERTER

RC-1001 RC-1001A

Fig. 1-2 Front View of the WEB SMART MEDIA CONVERTER

LED Indicators Description

LED Color Function

POWER Green Lit when +5V power is coming up
FX LINK/ACT Green

Lit when fiber connection is go od
Blinks when any traffic is present

TP LINK/ACT Green

Lit when TP connection is good
Blinks when any traffic is present

TP 10/100 Amber

Lit when 100Base-TX is active
Off when 10Base-T is active

Table 1-1

Fig. 1-3 Rear View of the WEB SMART MEDIA CONVERTER

Reset button:

Press this button over 5 seconds then
(1) Restore to default
(2) Reboot

Publication date: March, 2011

Revision A2

4

2. Installation

2-1. Cable and Hardware Installation

 Wear a grounding device for electrostatic discharge

 Verify that the AC-DC adapter conforms to your country AC power requirement

and then insert the power plug

• TP Cable

 Use Cat. 5 TP cable to connect server/host or work s tation to TP port of the

converter

 TP port supports MDI/MDI-X auto-crossover, use:

straight-through cable (Cable pin-outs for RJ-45 jack 1, 2, 3, 6 to 1, 2, 3, 6)
to cascade or up-link the converter to an upper layer L2/L3 switch or
server/host/work station

 TP Cable Limitations: Cat. 5 and up to 100m

• Fiber Cable

 Use fiber cable to connect FX port of an upper layer converter
 Fiber Cable Limitations:

SC/LC Converter Models

Multi-mode Half-duplex 412m
Multi-mode Full-duplex 2Km

Single-mode Half-duplex 412m
Single-mode Full-duplex 10/30/50Km

Table 2-1

Note: The other side of the fiber cable plugg ed into the c onverter’s RX connector at

the near end sh ould plug into the FX device ’s TX connector at the far en d,
and vice versa.

Publication date: March, 2011

Revision A2

5

3. Operation of Web-based
Management

The converter prov id es a web f unc tio n by Ethernet Port (Br o wser) to manage
and monitor the port activity. For instance, http ://192.168.1.1, then enter password
and click “Login” button.

The default values of Web Smart Media Converter are as follows:
IP Address :192.168.1.1
Subnet Mask :255.255.255.0
Default Gateway :192.168.1.254
Password :admin

Fig. 3-1

Publication date: March, 2011

Revision A2

6

3-1. Web Management Home Overview

Home Page and Main MENU will be shown up after you fill in “admin” to
serve as password an d click the <Login> button. T he main functions will be listed
on the left side of a browser. On the top is the fr ont panel view of the converte r. In
the middle is the basic S ystem Inform ation. T he m ain f unctio ns wil l be i ntroduc ed in
the following sections.

On the front panel, t he LEDs will displa y the status color which is the same
as physical hardware. The fiber and TP plug will display the status color as well.
Green stands for “Link up” status.

The main functions ar e “Information”, “Loc al Setting”, “Remote Setti ng”, and
“Tools”.

Function name:

System Information

Function description:

Show the local and remote device network information.

Fig. 3-2

Parameter description:

Remote Device Control:

Disable (Default):
When Remote Device Co ntrol is disabled, the r emote dev ice inform ation

will not be shown on the screen.

Publication date: March, 2011

Revision A2

7

Enable:
When Remote Device Cont rol is enabled, the rem ote device information

will be shown on the screen.

MAC address:

It is the Ethernet MAC address of the management agent in this device.

Software Version:

It’s a firmware version of this device.

IP address/Gateway/Subnet Mask:

It’s an IP address of the device.
Default Setting:

IP Address: 192.168.1.1
Default Gateway: 192.168.1.254
Subnet Mask: 255.255.255. 0

Description:

It is a field for model description.

Serial number:

It is a product serial number.

Hardware Version:

It is a hardware version of product.

Publication date: March, 2011

Revision A2

8

3-2. The Function Tree in Web Management

For offering you a clear guide to use this Web Smart Media Con verter, the
following is the whole function tree of Web Smart Media Converter in web
management. User can refer to the following sections based on the order of this
function tree below for more details.

Fig. 3-3

Publication date: March, 2011

Revision A2

9

3-3. Local Setting

3-3-1. IP Configurat io n

IP configuration is one of the mos t important configur ations in WEB SMA RT
MEDIA CONVERTER. Without the proper setting, n etwork manager will not be abl e
to view the device. WEB SMART MEDIA CONVERTER supports both manual IP
address setting and automatic IP address setting via DHCP server. When IP
address is chan ged, you must r eboot the conver ter to have the s etting taken effect
and use the new IP to browse for web management.

Function name:

IP Configuration

Function description:

Set IP address, subnet mask and default gateway for WEB SMART MEDIA
CONVERTER.

Fig. 3-4

Fig. 3-5 IP Configuration

Publication date: March, 2011

Revision A2

10

Parameter description:

DHCP Client:

WEB SMART MEDIA CONVERTER supports DHCP client used to get an
IP address autom atically if you set this function “Enable”. W EB SMART
MEDIA CONVERTER will find the DHCP server existed in the network to
get an IP address . If this function is set “Disable”, you hav e to input IP
address manually.

Default: Disable

IP address:

Users can configure the I P settings and fill in new values if users set the
DHCP function “Disable”. Then, click <Apply> button to update it.

Default: 192.168.1.1

Subnet mask:

Set the subnet mask value which is the same as that of network it
attaches. For more inf ormation, please also see th e section “IP Address
Assignment” in this manual.

Default: 255.255.255.0

Default gateway:

Set an IP address for a gateway to handle those packets that do not
meet the rules predefined in a device. If a packet does not meet the
criteria for other routers, then it must be sent to a default router. This
means any packet with undefined T CP/IP information will be sent to t his
device unconditionally.

Default: 192.168.1.254
Description:
Input data or model name about this device then click <Apply> button.

Publication date: March, 2011

Revision A2

11

3-3-2. Password Setting

Function name:

Password Setting

Function description:

The default user ac count is “ admin” that can not be m odif ied or dele ted and is
the only one user account. T he password mus t be ‘a’-‘z’, ‘A’-‘Z’, ‘0’-‘9’ and ‘_’.
The max. length is 16 characters. After input the data as Fig. 3-6 click
<Apply> button.

The default setting of user account is:

Username: admin

Password: admin

Parameter description:

Old Password:
Input the old password
New Password:
Input new password
Confirm:
Input the new password again

Fig. 3-6

Publication date: March, 2011

Revision A2

12

3-3-3. Converter Configuration

Function name:

Converter Configuration

Function description:

This converter provides the following configurable parameters.

Parameter description:

Jumbo Frame(9K):

If enable this function, the media converter could pass the max. 9KB

packets.

Link Transparent:

Only if link transparent is enabled, the Remote Fault Detect and Link

Loss Carry Forward will take effect.

Remote Fault Detect:

If enable this func tion, when f iber port enab le TS-100 0 and rec eive OAM

packet. This converter will set local UTP port link up or link down

Fig. 3-7 Converter Configuration

Publication date: March, 2011

Revision A2

13

according to remote device’s UTP port link status. This function need

enable link transparent first.

Link Loss Carry Forward:

If enable this func tion , whe n the UT P p ort link do wn, t he f iber por t will be

forced link down. And the fiber will be resume when UTP port link up.

This function need enable link transparent first.

Notice

：

If local MC (Media Co nverter) enables TS1000 an d is configured as

Center Mode, when configuring Jumbo Frame and Link Transparent

functions for local MC, the remote MC will be configured at the

same time even if it is a dump MC. And the configuration of remote

side is the same as local side.

Forward CRC Error Frame:

If enable this function , the CRC error packet will be pass, other wise, the

CRC error packets will be dropped.

Forward Pause Frame:

If this function was e nab le d , this MC wil l f orward pause fram e and r e gard

it as a normal packet.

Management Packet High Priority:

If enable this function , this MC will enable Q OS. W e enable four queu es,

and set queue 3 as strict priority. All management packets, such as

802.3ah OAM packets will be in queue 3 to guarantee bandwidth.

Broadcast Storm Filter, Multicast Storm Filter, Unknown DA Unicast Storm
Filter:

If enable this func tion, when too many broadc ast/multicast/unknown DA

unicast packets arrive in a period time, the packets will be dropped.

Publication date: March, 2011

Revision A2

14

3-3-4. Port Configuration

Function name:

Port Configuration

Function description:

Change the state and configuration of each port. This page could set local
device’s port status, include work mode, flow control ability, ingress and
egress rate limit.

Parameter description:

Port:

The TP Port is MEDIA CONVERTER’s Ethernet UTP interface.

The FX Port is MEDIA CONVERTER’s Ethernet Fiber interface.

Link:

Show port current link status:

100F = Speed 100M, Full Duplex Mode

100H = Speed 100M, Half Duplex Mode

10F = Speed 10M, Full Duplex Mode

10H = Speed 10M, Half Duplex Mode

Down = Link Down

Mode:

The Auto Speed algorithm to exchange the capability with the linked

partner. When enabled, the speed, duplex mode and f low control mode

may change. You must have both port configuration of local port and

linked partner be the sam e. If their configuration is different, the link will

not be set up successfull y. In WEB SMA RT MEDIA CONVE RTER, fiber

port supports forced mode only.

Set the mode of speed and duplex. In speed, 10/100Mbps baud r ate is

Fig. 3-8 Port Configuration

Publication date: March, 2011

Revision A2

15

available for Fast Ethernet. If the media is fiber, it is always 100Mbps and

the duplex is 100full/auto; if the media is TP, the Speed/Duplex is

comprised of the com bination of speed mode, 10/100Mbps, and du plex

mode, full duplex and half duplex.

Flow Control:

There are two m odes to choose in flow control, Enable and Disable. If

flow control is set “Enable”, both parties can send PA USE frame to the

transmitting device(s) while the receiving port is too busy to handle.

When it is set “Dis able” , flow co ntrol wil l not exis t in the por t. It drops th e

packet if too much to handle.

Default: Enable

Ingress Rate Limit and Egress Rate Limit:

There are some predefined rate settings. If user needs some special

usage, you cou ld input the rate b y yours elf after “User Setting” has bee n

selected from pull down list. Because the rate limit is 64kbps as a

minimal step, the inpu t rate lim it, it sh ould b e divide d ex actly b y 64. If the

rate value can not be div ided exactl y b y 64, f or exam ple 65, t he pr ogram

will be change the rate to 64 automatically.

Default: Not Limit

Publication date: March, 2011

Revision A2

16

3-3-5. MIB Counter

Function name:

MIB Counter

Function description:

The page shows loc al de vice’s MIB co unters. If c lick the “clear” button , all MI B
counters will be clear to zer o. Click the“r efres h” button, s how the curr ent MIB

counters again.

Parameter description:

TP:

To display the converter UTP port counter information.

FX:

To display the FX (The converter’s Fiber port) port counter information.

CPU:

To display the CPU (The converter’s CPU) counter information.

Fig. 3-9

Publication date: March, 2011

Revision A2

17

3-3-6. VLAN

The Converter supports Tag-based VLAN (802.1Q). VLAN configuration is
used to partition your LAN into small ones as your demand. Properly
configuring it, you can gain not only improving security and increasing
performance but greatly reducing VLAN management.

3-3-6-1. VLAN Group

Function name:

802.1Q VLAN Group

Function description:

If enable VLAN functions, user could set 16 VLAN entries. Each VLAN entry
could set VID and member port. The VID should be 1~4094.Others when the
member port is evoked, this port will belongs to this VLAN group.

Fig. 3-10

Publication date: March, 2011

Revision A2

18

Parameter description:

VLAN Group:

To display the VLAN Group Index. The maximum is 16 and the range is

from 0 to 15.

VID:

VLAN identifier. Each tag-based VLAN group has a unique VID. It

appears only in tag-based and Double-tag mode.

TP:

To evoke the TP (The converter’s UTP port) to become a VLAN group

member.

FX:

To evoke the FX (The converter’s Fiber port) to become a VLAN group

member.

CPU:

To evoke the CPU (The converter’s CPU) to become a VLAN group

member. It means that CPU needs to become a VLAN member for

management purpose.

Publication date: March, 2011

Revision A2

19

3-3-6-2. VLAN Per Port Se tt in g

Function name:

802.1Q VLAN Per Port Setting

Function description:

In this page, we could set each port’s PVID and egress tag behavior.

Parameter description:

Egress Link Type:

Replace Tag:

The switch will remove VLAN tags from packets then add new
tags to them. The inser ted tag is the ingress port’s “Def ault tag”,

which is indexed by port “ Port based VLAN index”. This is a
replacement processing for tagged packets and an insertion for

untagged packets.

Remove Tag:

The switch will remove VLAN tags from packets, if they are
tagged when these pack ets are output. The switc h will not modif y
packets received without tags.

AddTag:

The switch will add VLAN tags to pack ets, if they are not tagged
when these packets are output on this port. The switch will not
add tags to packets already tagged. The inserted tag is the
ingress port’s Def ault tag, which is indexed b y port’s “Port based
VLAN index”.

Don’t Touch Tag:

Do not insert or remove VLAN tags to/from packet which is output
on this port.

Port VLAN Entry:

Select Port based VLAN index. The number means VLAN table
entry index, not VID.

Ingress Filter:

Fig. 3-11

Publication date: March, 2011

Revision A2

20

Enable or Disable VLAN ingress filter.

Publication date: March, 2011

Revision A2

21

3-3-7. Q-in-Q

Function name:

Q-in-Q

Function description:

This page could configure Q in Q function.

Fig. 3-12

Fig. 3-13

Publication date: March, 2011

Revision A2

22

Parameter description:

Out Layer VLAN Tag:

User defined Q-in-Q out layer VLAN tag Ether type.

Out Layer VLAN VID:

User defined Q-in-Q out layer VLAN tag VID

VLAN Tag Priority Decision:

Decide out layer VLAN Tag’s priority, use internal VLAN tag priority or

use IP remarking priority.

Q in Q direction:

Select Q in Q direction, which port adds tag, and which port removes tag.

“TP Port Add Q in Q Tag F X Port Rem ove Tag” or “FX Port Add Q in Q

Tag TP Port Remove Tag”.

Publication date: March, 2011

Revision A2

23

3-4. Remote Setting

Fig. 3-14

3-4-1. TS-1000 Functions

TS-1000 Functions include “TS1000 Setting”, “Loopback Test”, “Remote

Device Reset”, “Remote Port Information”, “Remote Port Setting” five functions.

3-4-1-1. TS-1000 Setting

Function name:

TS-1000 Setting

Function description:

This page could enable /disable TS1000 functio n, and set TS-1000 mode as
terminal or center. If TS1000 is enabled, the TS1000 information will be
displayed in the web. And if it’s in center mode, and remote device is in
terminal mode, remote TS1000 information will also be shown in the page.

Publication date: March, 2011

Revision A2

24

Fig. 3-15

Publication date: March, 2011

Revision A2

25

3-4-1-2. Loopback Test
Function name:

Loopback Test

Function description:

This page could start TS1000 loopback function. User could set TS1000
loopback packet number.

Fig. 3-16

Parameter description:

Send packet number:

After input the number between 1 and 255, click the “<Apply>” button.
Result:

Pass or not as Fig. 3-16
Result Counter:
Show packet number and pass or not

Publication date: March, 2011

Revision A2

26

3-4-1-3. Remote Device Reset
Function name:

Remote Device Reset

Function description:

We could reset remote device through this function. Before that “TS1000
ability” should be enabled, local device should be set in center mode and
remote device should be set in terminal mode.

Fig. 3-17

Parameter description:

Reset button:
After click this button, if success shown as Fig. 3-17.

Publication date: March, 2011

Revision A2

27

3-4-1-4. Remote Port Information

Function name:

Remote Port Information

Function description:

This page shows remote device port information.

Fig. 3-18

3-4-1-5. Remote Port Setting

Function name:

Remote Port Setting

Function description:

In this page, user could enable/disable remote device’s UTP port, change
remote device port’s speed & duplex and flow control ability. Fiber port
should not be disabled.

Fig. 3-19

Publication date: March, 2011

Revision A2

28

3-4-2. 802.3ah Function

This menu includes “802.3ah Configuration”, “Loopback Test”, “802.3ah
Status” three functions.

3-4-2-1. 802.3ah Configuration

Function name:

802.3ah Configuration

Function description:

This page could set IEEE802.3ah OAM function. User could enable/disable

802.3ah function and set its mode as passive or active mode.

Fig. 3-20

Parameter description:

802.3ah Function:
Enable/Disable

802.3ah Mode:

Active/Passive
Remote Loopback:
Enable/Disable

After select the parameters, then click the <Apply> button and
<refresh> button to show “Discovery Status” and “Fiber Port Status”.

Publication date: March, 2011

Revision A2

29

3-4-2-2. Loopback Test
Function name:

Loopback Test

Function description:

This page could start 802.3ah loopback test. User could configure packet
length and packet number.

Fig. 3-21

Parameter description:

Send Packet Number:
Available value:1~255
Packet Length (Not include CRC):

Available value:60~1514

After input the parameters, then click the <Apply> button.
Test result(Fig. 3-22, Fig. 3-23)

Fig. 3-22

Fig. 3-23

Publication date: March, 2011

Revision A2

30

3-4-2-3. 802.3ah Status

Function name:

802.3ah Status

Function description:

This page shows 802.3ah status information.

Fig. 3-24

Publication date: March, 2011

Revision A2

31

3-5. Tools

This menu contains “System Reboot”, “Save and Restore”, “Firmware

Upgrade” and “Logout” four functions.

Fig. 3-25

3-5-1. System Reboot

Function name:

System Reboot

Function description:

Click this function to reboot the device.

Fig. 3-26

Parameter description:

OK:

To restart the device.

Cancel:

To exit the function.

Publication date: March, 2011

Revision A2

32

3-5-2. Save and Restore

Function name:

Save and Restore

Function description:

SaveToFlash: Save local configuration to flash.
LoadFromFlash: Restore last saved configuration.
ResetToFactory: Factory default setting.

Fig. 3-27

Publication date: March, 2011

Revision A2

33

3-5-3. Firmware Upgrade

Function name:

Firmware Upgrade

Function description:

In this page, user co uld update t he firm ware by the web browser. User could
click the browser button, select the new firmware image file, and then the
new code image will be bur ned into th e flas h, and rese t the devic e to use th e
new firmware.

Fig. 3-28

Parameter description:

Browse:
To select the location of the firmware file.

Upgrade:
To execute “firmware upgrade” function.

3-5-4. Logout

Function description:

Logout

Function description:

Exit Web management.

Fig. 3-29

Parameter description:

OK:
T o exit Web management.

Cancel:
To cancel logout action.

Publication date: March, 2011

Revision A2

34

4. Maintenance

4-1. Resolving No Link Conditions

The possible causes for a no link LED status are as follows:

 The attached device is not powered on
 The cable may not be the correct type or is faulty
 The installed building premise cable is faulty
 The port may be faulty

4-2. Q&A

1. Computer A can connect to Computer B, but cannot connect to Computer C
through the WEB SMART MEDIA CONVERTER Converter.

 The network device of Computer C may fail to work. Please check the

link/act status of Computer C on the LED indicator. Try another network
device on this connection.

 The network configuration of Computer C may be something wrong. Please

verify the network configuration on Computer C.

2. The uplink connection function fails to work.

 The connection ports on another must be connection ports. Please check if

connection ports are used on that converter.

 Please check the uplink setup of the WEB SMART MEDIA CONVERTER to

verify the uplink function is enab le d.

Publication date: March, 2011

Revision A2

35

Appendix A

Technical Specifications

Hardware Specification

Feature Detailed Description

Power requ irement

5VDC

Power consumption

1.5 W

Fiber Connector

RC-1001:SC, LC / RC-1001A:SFP

Ambient Temperature

0 to 50 C

Humidity

5% to 90%

Dimensions

70.3(W) x 26.2( H) x 94(D) mm

Weight

0.44kg

Safety

Comply with FCC Part 15

Class A & CE Mark Approval

Shock IEC60068-2-27
Freefall IEC60068-2-32
Vibration IEC60068-2-6

Note: Any specification is subject to change without notice.