Rubicson Bike pedometer User Manual

manual

Bike pedometer

Item: 47981

www.rubicson.com
Box 50435
Malmö, Sweden

Version: 2021-03-08

EN

NO

SV

Rubicson®

ENGLISH

Functions

Note: Computer functions refer to the packing details.
Speedometer (SPD): 0~99.9 km/h or M/h
Average Speed (AVS): 0~99.9 km/h or M/h
Maximum Speed (MXS): 0~99.9 km/h or M/h
Speed Tendency
Speed Comparator (+ or-)
KM & M Selectable
Odometer (ODO) - 0~9999.9 km or M
Odometer Save Function
Trip meter (DST) - 0~999.9 km or M
Trip Timer (TM) - 9:59:59
Digital Clock- 12 / 24 hour selectable
Auto Scan
Auto Power Off
Auto Start / Stop
Calories
Fat Burned
Freeze Frame Memory (TM and AVS)
°C & °F selectable
Maintenance program
EL Backlight

or

Specications

Product material ABS acrylic
Size 75x50x15 mm
Batteries 2x CR2032
Transmission distance ≥ 70 cm
Waterproof grade IP65
Magnetic induction distance ≤ 3 mm
Signal transmission 110 kHz wireless transmission

ENGLISH

Accessories

Bracket

Magnetic screw
and spoke clamp

Transmitter

3V CR2032 x 2

Computer battery
Transmitter battery

Battery installation

Computer

Remove the battery cover from the
bottom of the computer using a at
blade screwdriver or a coin. Insert
the battery with the positive (+) pole
facing the cover and put the cover
back on. (Fig. 1).

Transmitter

Install the battery with the positive
(+) pole facing the battery cover.
Put the cover back on with a at
blade screwdriver or coin. (Fig. 2).

Computer base
rubber pad

Bef ore the
rstuse,
pleas e
take o ut
the batter y
insulator.

Bef ore the
rstuse,
pleas e
take o ut
the batter y
insulator.

Cable ties

Installation of the magnet & transmitter

Remove the magnetic screw from the spoke clamp. Place the
clamp on the spoke. You can use the clamp on both a at and a
round spoke. Screw on the magnetic screw to the clamp until it is
snug, do not overtighten. (Fig. 3).

32

ENGLISH

Attach the transmitter to the front bicycle fork using two cable
ties. Make sure the magnet cycles past the transmitter as the
wheel turns. As the magnet passes the transmitter, it should pass
within 3 mm of the transmitter, but not be able to touch it (Fig. 4).

Mounting bracket

Place the mounting bracket on a desired area of the handlebar (Fig. 5).
Wrap cable ties around the bar and thread through the opening of
the bracket tab.
Secure by pulling the ends of the strap down until locked.

ENGLISH

Computer

To attach the computer onto the mounting bracket, slide the
computer on the mounting bracket until it snaps rmly into
position (g. 6).
To remove the computer from the mounting bracket, press the
release button on the front of the bracket. Push the computer
forward with your thumb (g. 7).

Go to the computer setting mode by:
a) Insert the battery
b) Hold two buttons for 3 seconds
Press right button to select or adjust, press left button to conrm
the setting.

54

ENGLISH

Set the wheel size

Set the wheel size, factor C, into the computer by multiply the
wheel diameter in millimeter by 3.1416. For convenience, please
refer to the chart below.

Selection of kilometres or mile

After the wheel size is set, the following setting is the selection
of kilometers or miles as the measurement for distance. Press
the right button to choose between kilometer (km) or Mile (m)
and press the left button to conrm.

Km or m selection

ENGLISH

Age and weight

Set your age and weight.
Weight will be put in kg
or pound if km or mile is
selected, respectively.

Service program

The bike computer has a service program to remind you to
replace parts or lubricate the chains after a preset distance is
reached. Right after the km/mile selection is done, the preset
total distance of 600km (or miles) will ash. Press the right
button to select between 200, 400, 600 & 800 km (or miles) and
press left button to conrm your choice. For example, if 600 km
is set, the spanner ( ) will start to ash whenever the total
distance is reached; 600 / 1200 / 1800 etc. Press the left button to
stop the spanner ( ) from ashing.

Set the service program

Clock and time setting

Press the right button to enter the scan interface and press it
again to enter the time mode. Press and hold the left button for
3 seconds to enter the clock settings where you can choose
12 / 24-hour format. Press the right button to select and the left
button to conrm your choice. Continue with entering the hour
and minute settings.

76

ENGLISH

Selecting computer functions

a) Press the right button to go to another mode.
b) Press the left button to enter the sub-function of this mode.
c) By holding the left button, the computer will reset or go to the
setting mode of the sub-function.

Speedometer (SPD)

The current speed is indicated on the
rst row on the display. The range of
measurement is from 0 to 99km/h [0 to 99m/h].

Average speed (AVS)

The average speed will be reset when
resetting the Trip information which can be
found under the Trip distance mode.

Maximum speed (MXS)

Press and hold the left button for 3 seconds
to clear the maximum speed.

Speed tendency (acceleration & deceleration)

A cyclist symbol appears to the left of
the speed to indicate acceleration or
deceleration. The wheel turns forward

when accelerating and turns

backward when speed decreases.

ENGLISH

Speed comparator

A "+" or "-" sign may appear to the right of the
speed. A "+" indicates that you are travelling
faster than your average speed (AVS) and a
"-" indicate that you are riding slower.

Odometer (ODO)

The total distance travelled is indicated by
ODO. Hold the left button for 3 seconds to go
to odometer save function.

Odometer save function

Press the right button until entering the ODO mode
and press and hold the left button for 3 seconds until
the last digit is ickering. Press the right button to
select and press left button to conrm. Repeat above
sequence to reach desired odometer value. Press
the left button again to return to normal ODO mode.

Trip distance (DST)

To reset the Trip information, hold the left
button for 3 seconds. This action resets the
trip distance, trip timer and average speed.

Trip time (TM)

The trip timer will be reset when resetting
the Trip information which can be found
under Trip distance mode.

Temperature

To choose if temperature will show in °C or
°F, hold the left button for 3 seconds to enter
the degree selection. Press the right button
to select and press the left button to conrm.

98

ENGLISH

Calories

Hold the left button for 3 seconds to reset
the calorie data.

Fat burned

Fat burnt is measured in grams. Hold the left
button for 3 seconds to reset the data.

Scan

Press the right button to enter SCAN mode.
The trip distance, maximum speed, average
speed and

trip timer will be automatically

displayed every 4 seconds.

Freeze Frame Memory

Freeze Frame Memory can lock the display at the
end of a ride segment. Press the left button to
enter the mode. TM, DST, and AVS, which will be
ashing, can be read at a later time by pressing
the right button. To reset the memory, press the
left button; the display will stop ashing.
This function is particularly useful for example
after a competition or when not having the time
to analyze the data right away.
Note: Computer must be in either DST, MXS,
AVS, or TM mode for this function to work.

Start the computer

Press any button to wake up the computer and display before
cycling.

Auto power off

In order to save battery, the unit will go to sleep if no input is
received for 5 minutes.

Computer reset

ENGLISH

The computer will reset by either of the following cases.
a) Battery Change
b) Holding both left and right button for 3 seconds will reset the
computer.

Manual wake-up

Wake up the computer by pressing any button.

Auto wake-up

You can wake up the computer by simply riding the bike without
pressing any button. If you bike within 2 hours after sleep, the
computer will wake up within 10 second. If it has been more
than 2 hours after sleep, it will wake up within 1 minute.

EL backlight

To turn on the EL backlight you have two alternatives:
a) By holding the right button for 2 seconds, the EL light will
be turned on for 8 seconds. The computer will then go to scan
mode with trip distance, maximum speed, average speed and
trip timer displayed.
b) Press the left button to turn on the EL light for 4 seconds. The
computer will go to the freeze frame memory mode as well.

Error Problem/solution
Inaccurate maximum

speed reading
No speedometer

reading
The display is black Temperature is too hot, or display has been

No trip distance
reading alignment

Display shows
irregular gures

Unknown atmospheric or RF interference

Improper magnet/ transmitter alignment. Check
the battery and make sure it is inserted correctly.

exposed to direct sunlight for too long
Check for correct sensor/ magnet alignment and

check the battery and make sure it is inserted
correctly.

Take out the computer battery and insert it again.

1110