Rubbermaid FG750112 User Manual

TC AutoFoam Touch-Free Dispenser

Installation Instructions

Battery Installation Mounting Dispenser

1

2

3

4

Use the dispenser cabinet key to
open the front cover. Insert the key
into the holes located at the top of
the dispenser, twisting the key, and
pulling the cover towards you. The
cover is hinged at the bottom of the
dispenser.

Remove the soap refill pouch holder by
pulling it straight up.

Insert four C-cell alkaline batteries
(not included) making sure to place
batteries in the compartment in the
proper orientation as shown by the
diagram in the battery compartment.

Replace the soap refill pouch holder.

The dispenser will turn “on” automati­cally once batteries are installed.* You
will hear a long beep signifying the unit
is activated.

* If the dispenser appears
non-functional, remove batteries, wait
4 minutes and re-insert them.

1

2

2a

2b

The dispenser should be mounted

12.5 inches (31.75 cm) above the
counter-top, sink or other surface.
If an object remains in the sensing
range for more then 10 seconds,
the green LED will flash and no
soap will be dispensed after the
initial dose. Remove object and
unit will operate normally

NOTE: Insure that proper mounting hardware is used for
your particular wall composition.

Once the batteries have been installed, without a refill installed in
dispenser, close dispenser cover. The setup sequence will be
initiated. During this period, the sensor will automatically detect if
the dispenser is too close to a surface below by sounding a
beeping tone every half-second and the green indicator light will
flash once each second. As you are positioning the dispenser, you
can verify the proper mounting distance by moving the dispenser
away from the surface below the sensor until the tone and the
green indicator light cease. The dispenser can be mounted to

either a mirror or a tile surface using the double-sided tape
provided (2a) or mounting the dispenser to the wall (2b).

Using the template from the
dispenser carton, drill holes
into wall with a 1/4" or 6mm
drill bit where dispenser is to
be mounted. Remove template
and align holes in backplate of
dispenser with the pre-drilled
holes. Screws and anchors
have been provided to mount
the dispenser to the wall.

Use the alcohol wipe provided to
thoroughly clean any surface that will
have adhesive tape attached. Pull off
the protective backing off the
adhesive tape and mount the
dispenser to the wall holding it in
place for 10-15 seconds allowing
the tape to adhere to the mounting
surface. Remove the batteries from
the dispenser. Let the dispenser

set up for 24 hours before
installing the batteries and refill.

MIN

12.5 in

31.75 cm

.236 in
06 mm

DRILLING TEMPLATE

Drilling Template

From Side of

Dispenser Carton

CAUTION

PLEASE USE

DRILLING TEMPLATE

Wall Mount

World Headquarters:

Serving North and South America

Technical Concepts LLC
1301 Allanson Road
Mundelein, Illinois 60060 U.S.A.

Toll Free: 1-800-551-5155
Fax: [phone]

European Headquarters:

Serving Europe, Africa and Middle East

Technical Concepts International Ltd.
Peterborough, PE2 6WA, England
Phone: [phone]

Asian Headquarters:

Serving Asia and Pacific

Technical Concepts Asia
No. 887, Jalan Perindustrian Bukit
Minyak, Bukit Minyak
14100, Penang, Malaysia
Phone: [phone]

Printed on 10 percent post-consumer recycled paper.

www.technicalconcepts.com

Dispenser Activation

LED/Tone Indicatiors

Refill Insertion

1

2

1

2

3

4

Open dispenser cover with a
dispenser cabinet key.

Close dispenser cover.

5

Test for proper operation, by dispensing soap into hand.

Snap the pouch fitment into the U-shaped bracket
insuring the nozzle fits into actuator lever. The pouch

fitment will snap into place once both brackets have snapped
over the fitment.

You will hear a long beep once the refill is properly
installed.

Remove the refill pouch from
the packaging box. Place the
refill pouch with the nozzle
pointing down into the pouch
holder. Remove and discard the
nozzle cap.

E000538 Rev 03

To activate dispenser, place hand under bottom of dispenser. If a
second dose is needed, remove hand, and then replace hand under
dispenser (when an object comes within 4 inches of the sensing
window the dispenser will activate).

The dispenser cover must be closed to activate.

Tone switch:

When switch is set to ON position there will be one beep.
When switch is set to OFF position there will be two beeps.

Note: Top “1-2” switch is not functional.

LED Indicators and Tone (IR sensor error indications):

Refill

After 2,650 doses a red LED flashes twice every 2 seconds along
with two beeps every 8 seconds indicating the refill needs to be
replaced. Be careful to not remove or dislodge the refill while
modifying any settings, as the dosing program will reset.

Batteries

When the batteries are low a yellow LED flashes once every 2
seconds, along with one beep every 16 seconds. 4 C-cell alkaline
batteries will last 120,000 hand washes or 3 years, whichever
comes first.

Object in Sensor Range (within 4 inches of sensor):

Refill in dispenser - If an object is in the sensor range more than

10 seconds then the green LED will flash once every second, one
beep every 1/2 second. Remove object and unit will operate
normally.

No refill in dispenser – If an object is in the sensor range then
the green LED blinks once every second and beeps every 1/2
second continuously as long as object remains in sensing range.

CLICKCLICK CLICKCLICK

NOTE: The dispenser and dose program resets
automatically each time a refill is installed. Sensor lens
should be cleaned after the refill is replaced.