Rubbermaid 5L10 User Manual
5L10
Congratulations and thank you for purchasing a Rubbermaid storage building.
BEFORE YOU BEGIN – BUILDING CODES
Be sure to check your local building codes, ordinances and restrictions, and applicable neighborhood governances.
BEFORE YOU BEGIN – SURFACE PREPARATION
To ensure proper assembly and performance your shed needs to be built on a solid, level surface.
A concrete or patio surface, or a treated-wood platform is recommended.
BEFORE YOU BEGIN – LOCATION
When choosing a location in your yard make sure you choose an area with easy access and one that provides
proper drainage for water to run away from the shed location.
BEFORE YOU BEGIN – PREASSEMBLY
Thoroughly review all assembly steps (it is important that
the steps are followed in the correct order). Review the
parts list and make sure that no parts are missing.
IMPORTANT – DO NOT RETURN TO THE STORE
For assistance with your Rubbermaid Storage Building
or for additional product information call our toll-free
Consumer Service number: 1-888-895-2110
M–F: 8:30 a.m. to 5:00 p.m. EST
or visit us online at: www.rubbermaid.com.
Installation Steps:
1. Site Preparation
2. Floor
3. Walls
4. Roof & Doors
5. Finishing
55 ¼"
76 ¾"
27 ½"
Note: Be sure to keep this instruction manual and your original store receipt to ensure our Consumer Service
Department can accurately and quickly assist you if necessary.
1780068
J
Safety
Glasses
Phillips Screwdriver
Rubber Mallet
Gloves
Utility Knife
RB
G
D
F
H
L
K
Description Part Number Assembly Letter Quantity Required Tools
Front Floor 5L01
Floor
Left Back 5L04
Right Back 5L05
Front Left Side 5L02
Walls
Front Right Side 5L03
Wall Connector 5H75
Left Door
Right Door
Doors
Door Handle 5L74
Lock Hasp 5F58
Front Roof 5L08
Roof
Roof Brace 5L36
5L06 / 5L41
5L07 / 5L42
Qx5
X
T
A
D
F
G
H
Q
L
K
T
X
J
RB
1
1
1
1
1
5
1
1
1
1
1
1
Phillips Screwdriver
Two Person Assembly
Safety
Glasses
Gloves
Utility Knife
Rubber Mallet
A
Phillips Bit
1/8" Drill Bit
(2) Step Stools/
Stepladders
Liquid
Soap
5L10
Drill
76 ¾"
#14 x 3/4" Combo Pan Head Screw
Accessory Bracket 5H88 4
Hardware
* Extra screws are supplied
AA
24*
PREASSEMBLY:
• Review ALL assembly steps before beginning construction.
• Review the parts list and make sure that no parts are missing.
55 ¼"
NOTE:
• To simplify assembly and to ensure proper engagement of all components,
apply a mild detergent to dovetail and snap fits before assembling.
27 ½"
"18
"24
"24
"~5
"~27-1/2
120.0
"24-7/8
"~55-1/4
"~4-1/2
"
3-5/8
"3-5/8
CAUTIONS
CARE & USE
CAUTION: Always use gloves when using a utility knife.
CAUTION: Always use eye protection/safety glasses
during assembly.
CAUTION: When installing screws, do not overtighten.
CAUTION: Drill only through initial panel wall, unless
otherwise indicated.
1.0 Site Preparation
• Shed can be cleaned with water and mild detergent as
necessary. DO NOT USE ABRASIVE DETERGENTS,
MATERIALS OR CLEANING TOOLS.
• To maximize your shed’s performance, remove
excessive snow and/or leaf accumulation from the roof.
• In the event of severe weather, please disassemble
and store in a secure location.
FLOOR PLAN:
Size the construction site to fit the entire floor.
OPTIONAL STEP:
If desired, recessed anchor locations (5 places)
can be used to anchor the shed floor to a foundation
after you have constructed one.
Build a solid, level surface for the shed foundation. Consult your
local building authority for ordinances, restrictions, or permits
required before building any structure at your home.
Note: Minimum dimensions for foundations shown.
55¼"
27½"
Maximum opening
ANCHOR
LOCATIONS
2.0 Floor Installation
Using a utility knife, cut the long side of each wall slot
a.
tab and then use a rubber mallet and screwdriver to
knock it out 8 places on Front Floor (A).
1.
2.
Using a rubber mallet and screwdriver, knock out the
b.
tabs for the door hinge, 2 places on Front Floor (A).
A
A
Drill pilot hole through top surface of floor, 2 places on Front Floor (A).
c.
CAUTION: Drill through top surface of floor only!
A
Loading...