Rubbermaid 402060 User Manual

®

AutoFlush®Clamp

AutoFlush® for Urinals

AutoFlush® for Toilets

4 “C” Alkaline Batteries

Next Generation

with Courtesy Flush (Toilets)
without Courtesy Flush (Urinals)
for Sloan and Zurn Models

INSTRUCTIONS

Manufactured by:

TECHNICAL CONCEPTS • 1-800-551-5155

The AutoFlush®sends out a continuous infrared beam that is reflected back by the presence of a person in front of the urinal
or toilet.“Object Lock”technology differentiates between someone walking past the unit or actually using the fixture.

AUTOFLUSH®COMPONENTS

Sensor

Adjustment Tool

Allen Wrench

NOTE: Fits Sloan and Zurn flush handles. To fit other flush handles contact TC customer service at 800-551-5155.

Courtesy Flush Button

Step 1.

If flush handle is leaking, replace before installing AutoFlush

Using the supplied Allen wrench,
remove battery compartment.

®

-

+

+

-

2.1 Open hinged screw covers

and loosen screws to leave a

1

⁄4”gap between the base

and mounting cover

2.2 Slide the AutoFlush

the flush handle and secure
the mounting clamp over the
existing handle base.

NOTE: If the unit is on a high mount
toilet flush valve where the flush han­dle is approximately 40”above the
floor,you should rotate the AutoFlush
down to ensure sensor is directed
at user.

®

on to

Step 3.Step 2.

2.1a

2.2a

®

2.1b

2.2b

1/4” Gap

Install 4 “C”cell alkaline batteries
into the battery compartment not­ing the battery position marks on
the inside of the compartment.
Slide the battery compartment into
the AutoFlush
compartment with Allen wrench.
The last three turns of the wrench
will activate the AutoFlush

®

unit and secure

®

unit.

--

++

+

-

1ON2

Courtesy Manual
Flush Button

(Toilet Model Only)

Allows manual activation
of flush if needed.

Battery LED (Yellow) Flashing LED = Change Batteries

Object Lock Sensor- Detects User or Object

User-In-View LED (Green) Flashes 3 Times = User acknowledged & ready to operate.

1ON2

-

+

Sensor Range

Adjustment Screw

Short

Long

Operation
Features*

Switch 1

24 Hours Flush Off

Switch 2

Alarm Tone Off

Switch 1

24 Hours Flush Off

Switch 2

Alarm Tone On

Switch 1

24 Hours Flush On

Switch 1

24 Hours Flush On

Switch 2

Alarm Tone On

Switch 2

Alarm Tone Off

Sensor Range Reset Button

Sensor Range

Adjustment

1ON2

1ON2

1ON21ON2

Step 4.

ACTIVATION

Your AutoFlush®unit comes preset from the facto­ry.If special circumstances require adjustment of
the activation distance,see Appendix A—
Adjusting Your AutoFlush

The AutoFlush

®

unit has a 7 minute start-up

®

.

sequence in which the Object Lock Sensor will
activate the User-In-View

ggrreeeenn LL..EE..DD..

continu­ously as long as a user or object is in view. After
the start-up sequence is completed and when the
Object Lock Sensor has a user in view,the User-In-

ggrreeeenn LL..EE..DD..

View

will flash 3 times once the user

is in front of the unit for a minimum of 5 seconds.

4.3

--

++

+

-

4.1

4.2

1ON2

Use Allen wrench to remove
battery compartment tray.

Remove cover by rotating the
cover up at the end over the
battery compartment and
slide out.

Remove rubber seal.

VISUAL INDICATOR GUIDE

USER-IN-VIEW L.E.D. (Green light flashes 3 times, after

5 second delay, when a user is in view. The green light
flashes constantly when a user is in view during
the 7 minute start up sequence).

BATTERY L.E.D. (Yellow light flashes
indicating it is time to replace
batteries with 4 new “C” cell alkaline batteries).

OBJECT LOCK SENSOR
(Detects user or object).

COURTESY MANUAL FLUSH BUTTON

(Allows manual activation of
flush when needed—Toilet
model only).

APPENDIX A - ADJUSTING YOUR AUTOFLUSH

®

TO CHANGE ACTIVATION DISTANCE FOR THE OBJECT LOCK SENSOR:

Remove battery compartment. See Step 1.

1

2 Remove cover. See illustration 4.2.

3 Replace battery compartment in AutoFlush®to activate unit and remove rubber seal. See Step 3.

4 Press sensor range reset button as indicated in Appendix A. NOTE:the green L.E.D.will flash continuously

when it has an object in view for the seven minute reset period.

5 Stand at desired activation distance.

6 Use provided sensor adjustment tool and turn Sensor Range Adjustment Screw all the way down (count-

er clockwise) and then turn slowly up (clockwise) until green L.E.D.begins to flash.

7 Ensure Object Lock Sensor is not detecting stall door or wall by closing door,stepping out of sensor path

and making sure green L.E.D.is not flashing. If sensor locks onto door or wall, unit will not flush properly.
Shorten activation distance.

8 Remove battery compartment,and replace cover. Replace battery compartment tray to reactivate

AutoFlush

9 After 7 minute start-up sequence,the green L.E.D.will flash only 3 times when a user is in view

(after a 5 second delay).

®

unit.

TROUBLE SHOOTING GUIDE

Green L.E.D.(light) flashes 3
times when there are no users

Green L.E.D.(light) flashes
continuously when Object Lock
Sensor is activated by a user

PROBLEM CAUSE SOLUTION TO PROBLEM

Yellow L.E.D.(light) flashes

Not enough water to fixture or
too much water to fixture

Flush valve will not operate

Water continuously runs

Unit does not flush even after
Sensor Range has been
adjusted

Front of Object Lock Sensor is covered or Object
Lock Sensor is set too far out,detecting the
opposite wall or door as a user

AutoFlush®unit is in 7 minute start up mode
(when first activated) or Sensor Range Reset
Button has been depressed

Batteries are low and need replacing

Flush valve diaphragm damaged or valve
control stop improperly adjusted

Object Lock Sensor range set too close to
AutoFlush®, batteries are dead,or water supply
is turned off

Dirt or debris preventing diaphragm from func­tioning properly

Dead batteries

Remove item covering sensor or adjust Object Lock
Sensor activation distance.(See Appendix A ­Adjusting the AutoFlush)

Green L.E.D.(light) will flash only 3 times
acknowledging a user is in view after the 7 minute
start up mode

Replace batteries. Use ONLY alkaline batteries

Consult flush valve manufacturers directions

Adjust Object Lock Sensor—Replace batteries—Turn
water on.If the AutoFlush®does not begin to function,
call [phone] for technical assistance.

Consult flush valve manufacturer’s directions

Replace batteries.

Have Questions or Need Supplies?

Call Toll Free:1-800-551-5155

World Headquarters:

Serving North & South America

Technical Concepts LLC.

1301 Allanson Road
Mundelein, Illinois 60060 U.S.A.

®

☎ 847-837-4100
Fax: [phone]

Toll Free: 1-800-551-5155 Web: www.technicalconcepts.com Email: [e-mail]

European Headquarters:

Serving Europe, Africa & Middle East

Technical Concepts International Ltd.

Pin Green Business Park Eastman Way
Stevenage, Herts SG1 4UH, England
☎ [phone]
Fax: [phone]

Asian Headquarters:

Serving Asia & Pacific

Technical Concepts Asia

51 (B) Lorong Perindustrian Bukit minyak 9
14100 Bukit Mertajam, Penang, Malaysia
☎ (60) 4 508 5008
Fax: [phone]

108112