Rubbermaid 1S84 User Manual
M
GG
E
C
K-5H52
X
N
AN
RS
RL
P
T
AP
L
T
FF
G
T
L
D
P
T
N
D
M
X
C
Q
D
C
J
Q
AF
F
AK
H
J-5H51
Description Assembly Letter Quantity Required Tools
Front Floor Panel J-5H51 1
Repeat Floor Panel K-5H52 2
Left Side Panel C 3
Right Side Panel D 3
Left Back Panel E 1
Right Back Panel G 1
Left Front Panel H 1
Right Front Panel J 1
Wall Connector Q 24
Left Door AK 1
Right Door AF 1
Lock Hasp X 1
Window for Door LL 2
Gasket for Door Window MM 2
Door Reinforcement NN 2
Hinge Reinforcement PP 2
Handle Kit QQ 1
Spring Bolt Kit SS 1
Left Roof Panel NN 2
Left Skylight Roof Panel AN 1
Right Roof Panel P 2
Right Skylight Roof Panel AP 1
Gable M 2
Ridge Beam - Long RL 1
Ridge Beam - Short RS 1
Ridge Connector FF 2
Ridge Cap GG 1
Ridge Tape HH 2
Skylight w/Gasket Installed L 2
Roof Connector T 16
#14 x 1.0" Combo Pan Head Screw AA 56
#14 x 5/8" Combo Pan Head Screw JJ 12
#8 x 1/2" Combo Pan Head Screw KK 30
#8 SAE Flat Washer TT 30
1/4-20 x 0.5" Combo Round Head Bolt BB 4
1/4-20 Flat Washer Zinc CC 2
1/4-20 Hex Nut DD 4
HARDWARE ROOF DOORS WALLS FLOOR
Roof Pin EE 4
Safety Glasses
Rubber Mallet
Phillips Screw Driver
Liquid Soap
(2) Step Stools/Stepladders
Two Person Assembly
1S84
94.63"
128.85"
88.09"
RUBBERMAID
7' x 10' 6" RESIN STORAGE BUILDING
ASSEMBLY INSTRUCTIONS
Pre-Assembly:
• Review the parts list and make sure that no parts are missing.
• Review ALL assembly steps before beginning instructions.
• Level the area where the shed will be located.
• Areas of "fill dirt" should be tamped/compacted to prevent settling/sinking.
• If a foundation is desired, it should be constructed before assembly.
NOTE:
To simplify assembly and to ensure proper engagement of all components,
apply a mild detergent to dovetail and snap fits before assembling.
In the event of severe weather, please disassemble and store in a secure location.
1
Level construction site before beginning assembly of shed. A foundation may be
constructed if desired.
7
"
/16
127
FLOOR PLAN:
Size the construction site to fit the entire floor. Allow clearance for opening front and back doors.
OPTIONAL STEP:
If desired, recessed anchor locations (8 places) can be used to anchor the shed floor to a foundation
after Step 6.
41/8"
4-1/8
106[ ]
39-7/8
1014[ ]
"
76
4-1/8
41/8"
106[ ]
33/4"
3-3/4
95[ ]
1277/16"
1287/8"
81-1/2
2070[ ]
811/2"
ANCHOR
LOCATIONS
127-1/8
3228[ ]
1271/8"
128-7/8
3273[ ]
2
37-5/8
955[ ]
84"
375/8"
7-1/2
71/2"
190[ ]
4-1/8
41/8"
106[ ]
84"
84-3/8
2142[ ]
41/8"
4-1/8
106[ ]
30"
Using a utility knife, cut the long sides of each wall slot tab and then use a screwdriver to knock it out 8 places on Front Floor Panel (J-5H51). Open hinge holes 2 places.
7-1/2
190[ ]
71/2"
30"
J-5H51
3
Using a utility knife, cut the long sides of each wall slot tab and then use a screwdriver to knock it out 6 places on Floor Panel (K-5H52) used in the MIDDLE position and 12 places on Floor Panel
(K-5H52) used in the Back position.
4
K-5H52 (BACK POSITION
K-5H52 (MIDDLE POSITION
Place the Floor Panel (J-5H51) on the foundation. Connect two Repeat Floor Panels (K-5H52), install Screws (AA) 14 places.
Optional Step:
If desired, recessed anchor locations (8 places) can be used to secure the Floor to the Foundation, see Step 1.
)
)
AA
(28)
K-5H52 (BACK POSITION
K-5H52 (MIDDLE POSITION
)
)
J-5H51
Caution: When installing screws do not overtighten.
5
Using a screwdriver, punch out the screw holes on the top of Left Side Panel (C) 2 places.
Connect Left Side Panel (C) into Front Floor (J-5H51).
6
Lubricate dovetails on Left Front Panel (H) 4 places with liquid soap.
Connect Left Front Panel (H) into dovetails of Left Side Panel (C), engage snaps on
bottom of Left Front Panel (H) into Front Floor (J-5H51).
Dovetail
7
Screw Holes
C
J-5H51
C
click
Using a screwdriver, punch out the screw holes on the top of the Left Side Panel (C)
2 places.
Align lap joint between Left Side Panels.
Connect Left Side Panel (C) into Repeat Floor (K-5H52).
8
1
2
C
H
click
Install Wall Connectors (Q) 5 places.
J-5H51
1
2
click
click
1
Screw Holes
C
C
K-5H52
C
C
C
Q
C
C
1
2
C
2
9
C
C
C
Q
C
click
Using a screwdriver, punch out the screw holes on the top of the Left Side Panel (C)
2 places.
Align lap joint between Left Side Panels.
Connect Left Side Panel (C) into Repeat Floor (K-5H52).
C
C
K-5H52
10
Install Wall Connectors (Q) 5 places.
1
2
C
C
1
2
11
Lubricate dovetails on Left Back Panel (E) 4 places with liquid soap.
Connect Left Back Panel (E) into dovetails on Left Side Panel (C), engage snaps
on bottom of Left Back Panel (E) into Repeat Floor (K-5H52).
1
2
E
C
K-5H52
1
2
14
12
Repeat Steps 8-13 to assemble right side of shed.
Continue to Step 15.
See Step 8
See Step 11
See Step 10
See Step 13
See Step 12
D
D
See Step 9
D
J
Loading...