RTS PS-20 User Manual
PS-20
Power Supply
The RTS PS-20 is the new agship of a complete independent TW power supply. The PS-20 features two- and four-channel
operation, RTS monitoring, two-channel program input, audio linking, and three-mode operation: RTS 2-channel, RTS 4-channel and Clear-Com mode. It also has double the power output of the PS-31 per channel, which will increase the number of user
stations and beltpacks which can be connected substantially.
The PS-20 features two channels of communication where both channels are “wet”, meaning there is power on each channel
(RTS two-channel mode). In RTS four-channel mode, the audio signals and DC exist on the same wire. The PS-20 can also be
switched into Clear-Com mode. The PS-20 has a 3-pin XLR (male) connector on the front of the system, where a RTS user station can connect and monitor activity on either or both channels. A single PS-20 power supply has 1.8 ampere per channel which
means the user can power up more stations (see specications for details). If additional user stations or beltpacks are needed,
two PS-20’s can be joined together to double the power capability. A pair of standard stereo plug connectors are available on the
back of the power supply to connect two PS-20’s through audio linking as well . The PGM IN (3-pin XLR female Program Input)
connector can be used to send audio to both CH 1 and/or CH 2.
Features
Selectable Mode Operation
The PS-20 is selectable between RTS 2-channel, RTS
4-channel and Clear-Com mode.
Audio Linking
There is an audio link connection (¼” (6.3mm) Stereo plug)
on the back of the unit.
Monitoring
The 3-pin XLR Monitoring output connector on the front of
the PS-20 allows the user to connect a RTS user station to
monitor a channel or both channels.
Status Indicators
There is a green status indicator for each channel on the
front of the unit. Each of these indicators will remain lit during
normal operation, but will turn RED during a channel current
overload condition. Output current is automatically reduced
during an overload, and normal operation is restored when
the overload is removed.
Line Drawing
Program Input
There is a Program Input connector on the rear panel. This
can be used to connect a device that both channel 1 and
channel 2 can listen to at the same time. A Channel Select
switch on the front panel assigns the program to either or
both channels. A Level control adjusts the program level to
the intercom channel.
Intercom Channels Connections
Intercom channels (user stations) are connected to the rear
panel of the PS-20 with 3-pin XLR connectors.
Selectable Termination Impedance
The IMPEDANCE SELECT switch on the rear panel allows
each channel to be set for 200Ω or 400Ω operation. Select
200Ω for each channel operated independently. Select 400Ω
for each channel connected to another channel.
PS-20 Specications
General
Input Voltage: 90 to 264 VAC, 50 to 60 Hz
Output Voltage: 28 VDC to 32 VDC
Output Current: 2.00 Amps Maximum per channel
Termination Impedance: Selectable 200 Ω / 400 Ω
1.8 Amps maximum per channel
Ripple: < 0.2 V
Program Input Levels:
Nominal +2 dBu
Balanced, High Impedance >10 kΩ
Two-Wire Output Levels:
Nominal 30 VDC
Unbalanced, selectable 200 Ω / 400 Ω
Monitor Output:
Nominal Gain of 0 dB for 1000 mVRMS input level on
the program input. 30 VDC nominal, 100 mA maximum.
Audio Link: Nominal input 2 dBu with a Gain of 0 dB
Connections
Type: 3-pin XLR male (RTS 2-channel Mode)
Pin 1 Common for Audio and DC
Pin 2 30 VDC and Mixed Audio Channel 1
Pin 3 30 VDC and Mixed Audio Channel 2
Type: 3-pin XLR male (RTS 4-channel Mode)
Pin 1 Common for Audio and DC
Pin 2 30 VDC and Mixed Audio Channel 1 or 3
Pin 3 Mixed Audio Channel 2 or 4
Type: 3-pin XLR male (Clear-Com Mode)
Pin 1 Common for Audio
Pin 2 30 VDC
Pin 3 Mixed Audio Channel 1 or 2
Program Input
Type: 3-pin XLR female
Pin 1 Common
Pin 2 Balanced Audio + Input
Pin 3 Balanced Audio - Input
Output ¼” Stereo Phono Jack
Tip: CH3
Ring: CH4
Sleeve: Ground
AC Input
Type: Universal AC Plug
Pin 1 Hot
Pin 2 Neutral
Pin 3 Earth Ground
Monitor Output
Type: 3-pin XLR male (RTS 2-channel Mode)
Pin 1 Common for Audio and DC
Pin 2 30 VDC and Mixed Audio Channel 1
Pin 3 30 VDC and Mixed Audio Channel 2
Type: 3-pin XLR male (RTS 4-channel Mode)
Pin 1 Common for Audio and DC
Pin 2 30 VDC and Mixed Audio Channel 1
Pin 3 Mixed Audio Channel 2
Type: 3-pin XLR male (Clear-Com Mode)
Pin 1 Common for Audio
Pin 2 30 VDC
Pin 3 Mixed Audio Channel 1 or 2
Environmental
Operating Temperature: 0° C - 50° C (32° F to 122 ° F)
Storage: -40° C to 70° C (-40° F to 158° F)
Humidity: 0 to 95%, non-condensing
Dimensions and Finish
Height: 1.72” (44 mm) - 1 RU
Width” 8.186” (207.9 mm)
Weight: Under 5lbs.
Finish: Thermoplastic front panel, Aluminum case, RTS
light gray paint - black silkscreen.
Mounting: MCP Style rack kit or (included rubber
adhesive feet).
Audio Link
Input ¼” Stereo Phono Jack
Tip: CH1
Ring: CH2
Sleeve: Ground
Contact Information
Telex Communications, Inc.
12000 Portland Avenue South
Burnsville, Minnesota 55337
Telephone: (800) 392-0498
Fax: (800) 323-0498
Form Number: LIT000055000
Date: July, 2007
Ordering Information
PS-20
Power Supply
Catalog Number:
90007854000 US Power Cord
90007854100 Euro Power Cord
90007854200 UK Power Cord
This specications information is preliminary and is subject to change without notication.
Brand names mentioned are the property of their respective companies.
Loading...