1
It’s Under Control
®
T1-B
Universal System Controller
It’s Under Control
®
Operation Guide
70-210053-18 V 1.0
Universal System Controller
T1-B
2
Copyright © 2009
Remote Technologies Incorporated
All rights reserved.
3
It’s Under Control
®
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation.
This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received including interference
that may cause undesired operation.
FEDERAL COMMUNICATIONS COMMISSION NOTICE
117 612 914
DECLARATION OF CONFORMITY (DOC)
The Declaration of Conformity for this product can be found on the RTI website
at: www.rticorp.com/declaration
FCC ID: MMURTI1100
IC (Canada): 3166A-RTI1100
Universal System Controller
T1-B
4
For environmental reasons, your T1-B Universal System Controller
uses “environmentally sound” Lithium-ion rechargeable batteries.
These batteries do not contain any poisonous heavy metals that can
damage the environment.
In the interest of recycling, please do not dispose of these batteries in the
household waste at the end of their useful life. Instead, dispose of them at an
appropriate collection site.
SAFETY SUGGESTIONS
Read Instructions. Read all safety and operating instructions before operating
the unit.
Retain Instructions. Keep the safety and operating instructions for future
reference.
Heed Warnings. Adhere to all warnings on the unit and in the operating
instructions.
Follow Instructions. Follow operating instructions and instructions for use.
Heat. Keep the unit away from heat sources such as radiators, heat registers,
stoves, etc., including ampliers that produce heat.
Do Not Open Battery Compartment. This device contains Lithium-Ion or
Lithium-Polymer batteries. Batteries should only be replaced by an authorized
service center or trained installer.
Power Sources. Connect the unit only to a power supply of the type described
in the operating instructions, or as marked on the unit.
Power Cord Protection. Route power supply cords so that they are not likely
to be walked on or pinched by items placed on or against them, paying particular
attention to the cord plugs at power receptacles and at the point at which they
exit from the unit.
Water and Moisture. Do not use the unit near water—for example, near a sink,
in a wet basement, near a swimming pool, near an open window, etc.
Object and Liquid Entry. Do not allow objects to fall or liquids to be spilled into
the enclosure through openings.
Servicing. Do not attempt any service beyond that described in the operating
instructions. Refer all other service needs to qualied service personnel.
Damage Requiring Service. The unit should be serviced by qualied service
personnel when:
The power supply cord or the plug has been damaged.
Objects have fallen or liquid has been spilled into the unit.
The unit has been exposed to rain.
The unit does not appear to operate normally or exhibits a marked change
in performance.
The unit has been dropped or the enclosure has been damaged.
BATTERY DISPOSAL
Li-ion
WARNING!
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THE UNIT TO RAIN OR MOISTURE.
5
It’s Under Control
®
Remote Technologies Incorporated warrants its products for a period of one
(1) year (90 days only for included battery packs) from the date of purchase
from Remote Technologies Incorporated or an authorized Remote Technologies
Incorporated distributor.
This warranty may be enforced by the original purchaser and subsequent
owners during the warranty period, so long as the original dated sales receipt
or other proof of warranty coverage is presented when warranty service is
required.
Except as specied below, this warranty covers all defects in material and
workmanship in this product. The following are not covered by the warranty:
Damage resulting from:
1. Accident, misuse, abuse, or neglect.
2. Failure to follow instructions contained in this Guide.
3. Repair or attempted repair by anyone other than Remote Technologies
Incorporated.
4. Failure to perform recommended periodic maintenance.
5. Causes other than product defects, including lack of skill, competence or
experience of user.
6. Shipment of this product (claims must be made to the carrier).
7. Being altered or which the serial number has been defaced, modied or
removed.
Remote Technologies Incorporated is not liable for any damages caused by its
products or for its failure of its products to perform, including any lost prots,
lost savings, incidental damages, or consequential damages.
Remote Technologies Incorporated is not liable for damages based upon
inconvenience, loss of use of the product, loss of time, interrupted operation,
commercial loss, any claim made by a third party or made by you for a third
party.
Remote Technologies Incorporated’s liability for any defective product is limited
to repair or replacement of the product, at our option.
If your T1-B Universal System Controller needs service, please contact Remote
Technologies Incorporated by telephone, fax or E-mail for return information.
Please do not return products to Remote Technologies Incorporated
without return authorization.
LIMITED WARRANTY
Universal System Controller
T1-B
6
All rights are reserved. No part of this document may be photocopied,
reproduced, or translated without the prior written notice of Remote
Technologies Incorporated.
The information contained in this document is subject to change without
notice. Remote Technologies Incorporated shall not be liable for errors or
omissions contained herein or for consequential damages in connection with the
furnishing, performance, or use of this guide.
Microsoft, Windows, Windows XP and Windows Vista are registered trademarks
of Microsoft Corporation in the United States and other countries.
T1-B, Integration Designer, and the RTI logo are registered trademarks of
Remote Technologies Incorporated.
Other brands and their products are trademarks or registered trademarks of
their respective holders.
DISCLAIMER
7
It’s Under Control
®
TABLE OF CONTENTS
Federal Communications Commission Notice .............. 3
Battery Disposal ......................................................... 4
Safety Suggestions ..................................................... 4
Limited Warranty ...................................................... 5
Disclaimer ................................................................. 6
Contents ..................................................................... 7
Chapter 1 - Welcome .................................................. 9
Features ................................................................. 9
Unpacking and Inspection ........................................ 10
Product Contents .................................................... 10
Chapter 2 - Introduction ............................................ 11
Important Notes ..................................................... 11
Compatibility .......................................................... 11
Software requirements ............................................ 11
Cleaning ................................................................ 11
Battery and Docking Station ..................................... 11
Remote Reference ................................................... 12
Docking Station Reference ....................................... 14
Chapter 3 - Operation ................................................ 15
Getting Started ...................................................... 15
Source Buttons ....................................................... 15
Chapter 4 - Specications .......................................... 17
Chapter 5 - Troubleshooting ...................................... 19
Chapter 6 - Service and Support ................................ 21
Index ........................................................................ 23
Universal System Controller
T1-B
8
9
It’s Under Control
®
Thank you for purchasing the T1-B Universal System Controller.
The T1-B is the second generation of RTI’s popular T1 universal system controller.
Completely customizable and programmable, the T1-B allows all other factory
remote controls to be combined into one simple, ergonomic user interface
providing powerful one-handed system control. Featuring a sleek new industrial
design and perfect assortment of keypad buttons for commonly used functions,
the T1-B can operate today’s sophisticated media system, no matter how
complex, at an affordable price.
While the T1-B is perfect for any media room, it is powerful enough to
control virtually any aspect of the home or ofce. Buttons can be individually
programmed to control devices or execute multi-step macros for complex
installations involving many components. Source buttons can be custom labeled
to match the device being controlled for more intuitive control. The integrated
tilt switch, coupled with a Lithium-Ion battery and charging dock insure hours of
uninterupted control.
When other RTI devices are employed, the T1-B is capable of RF transmission
through walls and cabinets, RS-232 control, contact closures, power sensing and
much more. Whether used as a standalone device or integrated into a complete
RTI control solution, the T1-B will provide powerful and intuitive control of any
electronics system - from simple to sophisticated.
FEATURES
The T1-B provides superior quality and reliability as well as these features:
Comfortable ergonomic design permits effortless, one-handed operation.
Tilt switch can automatically turn on the backlight when picked up.
Eight source and four general purpose assignable/programmable keypad
buttons with keycap labels.
Forty assignable/programmable keypad buttons.
Intuitive layout of keypad buttons for commonly used functions.
Transmits IR and RF (or both - on a single button press!).
Optional RF receiver allows you to transmit through walls, cabinets, etc.
System includes a Lithium-Ion battery and docking station.
Docking station backlight may be disabled.
Extremely wide IR transmitting frequency range.
Optional ‘Voltage’ and ‘Video’ sensing modules to monitor power status of
equipment when used with certain RTI processors.
Optional interface for RS-232 controlled equipment when used with certain
RTI processors.
Non-volatile Flash memory stores your system conguration even when
power is not present.
Field upgradable rmware.
USB Programming.
CHAPTER 1 | WELCOME
Universal System Controller
T1-B
10
CHAPTER 1 | WELCOME
UNPACKING AND INSPECTION
After unpacking your new T1-B Universal System Controller, save all of the
packing materials in case you ever have to ship the unit.
Thoroughly inspect the T1-B and packing materials for signs of damage. Report
any damage to the carrier immediately. Report any equipment malfunctions
to Remote Technologies Incorporated or an authorized Remote Technologies
Incorporated distributor.
PRODUCT CONTENTS
Contents within the box include the following items:
One (1) T1-B universal system controller
One (1) Docking station.
One (1) Universal power supply for docking station
One (1) Operation guide.
Five (5) Keycap clusters (32 keycaps per cluster).
One (1) Wall-mount bracket.
Three (5) Mounting screws for wall-mount bracket.
Two (2) Drywall anchors.
11
It’s Under Control
®
CHAPTER 2 | INTRODUCTION
IMPORTANT NOTES
Please read these important notes about the T1-B:
The T1-B should be placed in an area where it is around normal room
temperature (between 60° F to 90° F).
Do not let the T1-B get wet. It should not be handled with wet hands or
placed in an area where it could get wet.
Do not subject the T1-B to smoke, dust, or vibrations.
Only use the power supply that is provided with the T1-B. Using the wrong
type of power supply may result in damage to the battery or electronic
components.
Do not disassemble the unit. Service of the T1-B should be performed by
authorized personnel only.
COMPATIBILITY
The T1-B and Integration Designer® software are compatible with infrared
(IR) commands with carrier frequencies between 15KhZ and 460KhZ, as well
as those commands that do not use a carrier. This covers virtually all of the
remotes that exist to date.
SOFTWARE REQUIREMENTS
The recommended minimum system requirements needed to run the
Integration Designer® software are as follows:
Windows XP®, Windows Vista® or later version of Microsoft operating
system.
CLEANING
To clean your T1-B, lightly dampen a lint-free cloth with a mild detergent, and
wipe the keypad and outer surfaces.
BATTERY AND DOCKING STATION
The T1-B uses a Lithium-Ion rechargeable battery. This battery does not exhibit
any type of “Memory Effect” from being charged too often. Since the T1-B can
safely be charged after each use, a docking station is included for convenience.
If left out of the docking station, the T1-B will remain in sleep mode for 1 – 2
months before shutting down. At that point the battery must be recharged.
If the T1-B battery capacity is reduced to approximately one hour of remaining
run-time, the Status LED will illuminate red while the unit is powered-up.
The T1-B Docking Station can be placed on a at surface such as a shelf or
table, or it can be mounted to a wall using the included mounting bracket. The
docking station LED illuminates red to indicate a charge in progress. The LED
will illuminate blue when the battery in the unit is fully charged or does not
need to be charged, unless the backlight dip switch located on the bottom of
the docking station is set to the “off” position. A fully discharged battery will
take approximately 2-4 hours to completely re-charge.
Universal System Controller
T1-B
12
CHAPTER 2 | INTRODUCTION
Front
Status LED
Source (8) Keypad Buttons,
Keycaps Provided
General Purpose (4) Keypad
Buttons, Keycaps Provided
Predened Keypad Buttons
Back
Docking Station Contacts
On/Off Switch
IR Transmission Window
USB Programming Port
Metal Battery Retainer Clip
Battery
13
It’s Under Control
®
CHAPTER 2 | INTRODUCTION
Docking Station Top
Docking Station Front
T1-B in Docking Station
Charge Contacts
Universal System Controller
T1-B
14
CHAPTER 2 | INTRODUCTION
Docking Station Wall Mount Bracket
Docking Station Bottom
Screws Attach Wall Bracket to Dock
Wall Mount Holes
Bottom View
Wall Surface
Wall Mount
Bracket
Front View
Docking Station Backlight On/Off Adjustment
Docking Station Bottom
Docking station backlight
on/off dip switch
15
It’s Under Control
®
CHAPTER 3 | OPERATION
GETTING STARTED
NOTE: The following steps for initial installation including removing the battery
door should be performed by an authorized service center or trained installer
only.
The T1-B is shipped with the battery plugged in. The installer should turn on
the power switch.
The T1-B is turned-on by touching any keypad button. If the tilt sensor is
enabled, picking up the unit will also turn it on.
THE SOURCE BUTTONS
The eight source buttons at the top of the T1-B keypad have a special function,
so they behave differently from the other buttons. These buttons are used to
select the active source “page.” Whenever a source button is selected, all of the
other buttons on the keypad will switch to the programming associated with
that page. In order to indicate the active page, a red LED is always illuminated
more brightly behind one of the source buttons.
Despite their special function, the source buttons can be programmed to run
commands or macros in the same way that the other buttons can.
USING THE KEYCAP LABELS
The T1-B includes ve sets of 32 keycaps that include labelling for sources and
functions.
Prior to applying the keycap labels, remove the bezel from the T1-B.
The bezel is held on with magnets.
Bezel
Universal System Controller
T1-B
16
CHAPTER 3 | OPERATION
Using a scissors, individually cut-out the keycaps that will be used:
After the keycap is cut out from one of the sets, press it over an empty keycap
button. Make sure to press down rmly on the keycap until it is rmly seated.
Note: the keycaps can be permanently secured by using an adhesive that bonds
to silicon rubber. The following instant adhesive glue works well and is readily
available:
Silicon Adhesive: Loctite PRISM® 401 (p/n 40104)
U.S. Resellers: Contact East: # 173-606
McMaster-Carr: # 74765A63
Grainger: # 3KE58
Follow these steps to apply the Loctite #401 adhesive:
1. Apply a thin layer of the adhesive to the entire top surface of the
desired keycap button.
2. Press the desired keycap over the button.
3. Press down rmly on the keycap for 15 seconds.
Repeat these steps for each keycap on the T1-B. When nished applying
keycaps, replace the bezel on the T1-B.
PROGRAMMING THE T1-B
The T1-B is programmed using RTI’s Integration Designer® software.
A PC running Windows XP®, Windows Vista® or higher with a USB port is
required. The required USB cable is included with the RTI IR-PRO dealer kit.
Note: The T1-B will not operate normally while connected to a PC’s USB port.
Make sure you disconnect it from the computer to navigate pages or transmit
commands. In addition, the T1-B will not be able to sync with a computer’s USB
port while it is transmitting a command or running a macro.
Cut along the channels
that are the closest to
the keycap walls.
17
It’s Under Control
®
CHAPTER 4 | SPECIFICATIONS
Power 3.6 VDC, 950mAh Lithium-Ion Battery Pack
Power Management Automatic On/Off (tilt switch)
Infrared Control
Range
30 feet (9.1 meters) @ 60 degrees
Infrared Frequency
Transmission Range
15 kHz - 460 khz
Radio Frequency
Control Range
Up to 100 feet (30.5 meters)
with optional System Interfaces/Processors
Radio Frequency
Carrier
433 MHz
Operating
Temperature
+32° F to +122° F (0° C to +50° C)
Operating Humidity 5% to 95% Non-condensing
Backlight Blue LED, Red LED
Nominal Run Time
on Full Charge
3 hours continuous use
(20 to 30 days on average use)
Standby Time on
Full Charge
30 days
Battery Charge Time 3 to 4 hours
Total System
Memory
256K Flash (non-volatile) memory
Device Capability Total number of devices is limited only by memory
Macro Capability Unlimited steps per macro.
Total number of macros is limited only by memory
Macro capability on every button
Communications USB programming port
Dimensions
(L x W x D)
10.0 in (254mm) x 1.9 in (48mm) x 1.0 in
(25mm)
Enclosure High-impact molded ABS plastic
Weight 8.7 oz. (246 g) with battery pack
Warranty One Year (Parts & Labor) / 90 days on battery
All specications subject to change without notice.
Universal System Controller
T1-B
18
19
It’s Under Control
®
If you are having problems with your T1-B Universal System Controller, please
read the information below before contacting technical support.
If you continue to have problems, see Chapter 6 for more information on
contacting RTI technical support.
USB COMMUNICATION PROBLEMS
Make sure the battery pack connector is attached properly and the battery
is charged.
Verify that your PC is using Windows XP® or higher. The Integration
Designer™ software requires a USB device driver that may not be installed
on earlier versions of Windows.
Make sure that both ends of the USB cable are connected securely.
Make sure the PC detects the presence of the T1-B. If it doesn’t, unplug
the USB cable, wait for about ten seconds, and plug it in again.
If the download fails after some data has been transferred, try resending
the program.
IR CODE PROBLEMS
If you are using an IR repeater system, make sure it is working correctly
with the original OEM remote. If not, you will need to troubleshoot the IR
repeater system.
If you are still having problems, try adjusting the IR code “Minimum
Repeats” value in the Integration Designer™ programming software.
If the IR code is executed inside a macro that contains multiple IR codes,
try inserting a small time delay before the problem code. If there already is
a delay, try increasing it.
CHAPTER 5 | TROUBLESHOOTING
Universal System Controller
T1-B
20
21
It’s Under Control
®
For news about the latest updates, new product information, and new
accessories, please visit our web site at:
www.rticorp.com
CONTACTING RTI
For general info, you can contact RTI at:
Tel. (952) 253-3100
Fax (952) 253-3131
info@rticorp.com
RTI TECHNICAL SUPPORT
At RTI, customer service and satisfaction is an utmost priority. If you are
encountering any problems or have a question about your RTI product, please
contact RTI Technical Support for assistance.
RTI provides technical support by telephone, fax or e-mail. For the highest
quality service, please have the following information ready, or provide it in
your fax or e-mail.
Your Name
Company Name
Telephone Number
E-mail Address
Product model and serial number (if applicable)
If you are having a problem with hardware, please note the equipment in your
system, a description of the problem, and any troubleshooting you have already
tried.
If you are having a problem with software, please note what version you have
installed, the operating system on your PC, a description of the problem, and
any troubleshooting you have already tried.
If you are calling about a software or programming question or problem, please
be at you computer when you place your call. This will considerably speed up
the troubleshooting process.
For technical support or assistance with your T1-B, software, or accessories,
contact RTI at:
(952) 253-3137
support@rticorp.com
www.rticorp.com
For questions regarding service or repair of your T1-B, contact RTI at:
(952) 253-3136
service@rticorp.com
www.rticorp.com
Please do not return products to RTI without return authorization.
CHAPTER 6 | SERVICE AND SUPPORT
Universal System Controller
T1-B
22
CHAPTER 6 | SERVICE AND SUPPORT
Shipment of T1-B for Service
RTI will pay all labor and material expenses for all repairs covered by this
product’s warranty. If necessary repairs are not covered by warranty, or if a unit
is examined which is not in need of repair, you may be charged for the repairs
or examination.
If it is necessary to ship the T1-B Universal System Controller for service:
Please pack it securely (we suggest that it be insured).
Do not include accessories such as power cords or manuals unless
instructed to do so.
You must pay any shipping charges incurred in getting your T1-B Universal
System Controller to RTI. RTI will pay reasonable return shipping charges via
a carrier of our choice to any destination within the United States if the repairs
are covered under warranty.
A copy of the original dated sales receipt must be provided whenever warranty
service is required. You will need this receipt to establish the date of purchase.
23
It’s Under Control
®
INDEX
Contents ........................................................................... 7
Features ............................................................................ 9
Federal Communications Commission Notice .......................... 3
Introduction & Operation ................................................... 11
Battery ........................................................................ 11
Battery Disposal .............................................................. 4
Cleaning ...................................................................... 11
Docking Station............................................................. 13
Getting Started ............................................................. 15
Remote Reference, Front / Back ...................................... 12
Limited Warranty/Disclaimer ................................................5
Product Contents .............................................................. 10
Safety Suggestions ............................................................. 4
Service and Support ......................................................... 21
Contact RTI .................................................................. 21
Shipment for Service ..................................................... 22
Technical Support .......................................................... 21
Specications ................................................................... 17
Troubleshooting ................................................................ 19
Universal System Controller
T1-B
24
Remote Technologies Incorporated
5775 12th Avenue East, Suite 180
Shakopee, MN 55379
Tel: 952-253-3100
Fax: 952-523-3131
www.rticorp.com
© 2009 Remote Technologies Inc. All rights reserved. Printed in Taiwan.
It’s Under Control
®
Loading...