www.r-techwelding.co.uk
Email: sales@r-techwelding.co.uk
Tel: 01452 733933 Fax 01452 733939
PLASMA 60HF
INVERTER PLASMA CUTTER
OPERATION INSTRUCTIONS
2
3
Thank you for selecting the R-Tech Plasma 60HF Inverter Plasma Cutter
The Plasma 60HF has many benefits over traditional transformer
including infinite power control, HF pilot start and HF pilot restart which is ideal for cutting
mesh etc , quick fitting cost effective torch, long life cost effective torch consumables and
a 60% industrial duty cycle
We want you to take pride in operating our Plasma 60HF as much pride as we have taken
in making this product for you. Please read all information in this manual before operation
PLEASE EXAMINE CARTON AND EQUIPMENT FOR DAMAGE IMMEDIATELY
When this equipment is shipped, title passes to the purchaser upon receipt from the courier.
Consequently all claims for material damaged in shipment must be made by purchaser against the
transportation company used.
Please record your
can be found on data plate at rear of machine.
Product Plasma 60HF
Serial No. ___________________________________
Date of Purchase _____________________________
Where Purchased _____________________________
Whenever you request replacement parts or information on this equipment please always supply
information you have recorded above
This product is covered by 2 years parts and labour warranty, you are responsible for costs of shipping
unit to us, we will cover cost of returning item to you. External items, torch, earth lead etc are covered by
3 months warranty. Any faults/damage found caused by customer will be charged pro-rata.
Pay particular attention to the safety instructions we have provided you for your
protection
The level of seriousness to be applied to each section is explained below
plasma cutting equipment identification below for future reference. This information
plasma cutters,
WARNING
This statement appears where the information must be followed exactly to avoid serious personal
injury.
CAUTION
This statement appears where the information must be following to avoid a minor personal injury
or damage to this equipment.
A
A
4
Introduction
The R-Tech Plasma 60HF is a member of our field acclaimed family of
Premium features include:-
1. Inverter power source – more efficient to operate, provides smoother weld
characteristics.
2. Infinite cutting power adjustment, allows fine tuning of cut characteristics
3. HF Pilot start – Enables easy arc start even on painted surfaces
4. HF pilot arc restart – ideal for cutting mesh etc
5. Digital amp meters
6. Quick fitting torch for easy torch fitment/replacement
7. Long life – Low cost torch consumables
8. 60% Duty cycle at 40 Amps @ 40
Recommended Processes
The R-Tech Plasma 60HF is recommended for the plasma cutting processes within its output
capacity of 60 Amps DC
Equipment Limitations
The R-Tech Plasma 60HF is protected from overloads beyond the output ratings and duty cycle
as per machine specifications with thermostat protection of the output coils and rectifiers.
Cutting Capability – Duty Cycle
The R-Tech Plasma 60HF is rated at 60 Amps at 60% duty cycle on a ten minute basis. If the
duty cycle is exceeded a thermal protector will shut machine off until the machine cools.
ºC
welding products.
Technical Specifications
MODEL
Power Voltage
Input Current 12.5A
Rated Output Current 60 Amps
Current Adjusting Range 20-60 Amps
No-load Voltage 200V
Rated Duty Cycle 60%
Working Mode HF Start
ir Pressure 55 PSI
Max. Cutting Thickness (Clean cut mild steel) 17mm
Max. Cutting Thickness (Severance cut mild steel) 25mm
fter Flow Time 10 Seconds
Dimensions / Weight 620x260x550 mm / 30KG
PLASMA 60HF
415V 3-Phase 50/60Hz
Safety Precautions
Read entire section before starting installation
5
WARNING!
Electric Shock can kill – Only qualified personnel should perform this installation. Turn off input
power at the fuse box before working on this equipment. Do not touch electrically live parts.
Always connect the machine to an earthed mains supply as per national recommended
standards.
Select suitable location
Place the plasma cutter where clean cooling air can freely circulate in and out of the front & rear
louver vents. Dirt, dust or any foreign material that can be drawn through vents into plasma cutter
must be kept to a minimum. Failure to observe these precautions can result in excessive
operating temperatures which can lead to plant failure.
Grinding
Do not direct grinding particles towards the plasma cutter. An abundance of conductive material
can cause plant failure.
Stacking
This machine cannot be stacked.
Transport – Unloading
Never underestimate the weight of equipment, never move or leave suspended in the air above
people. Use recommended lifting equipment at all times.
WARNING!
Falling Equipment can cause injury. Never lift plasma cutter with gas bottle attached. Never lift
above personnel.
Tilting
Machine must be placed on a secure level surface or on a recommended undercarriage/trolley.
This machine may topple over if this procedure is not followed.
Environmental Rating
The plasma power source carries the IP21S rating. It may be used in normal industrial and
commercial environments. Avoid using in areas where water / rain is around.
6
Electrical Installation
WARNING!
ELECTRIC SHOCK CAN KILL
Machine grounding and High Frequency Interference Protection
This plasma cutter must be grounded to earth. See national electrical codes fro proper grounding
methods.
The high frequency generator being similar to a radio transmitter may cause interference to radio,
TV and other electronic equipment. These problems may be the result of radiated interference.
Proper grounding methods can reduce or eliminate this.
Radiated interference can develop in the following ways
1. Direct interference from welder power source
2. Direct interference from the welding leads
3. Direct interference radiated from feedback into power lines
4. Interference from re-radiation by un-grounded metallic objects.
Keeping these contributing factors in mind, installing equipment as per following instructions
should minimize problems.
1. Keep the welder input power lines as short as possible and enclose as much of them as
possible in metal conduit or equivalent shielding. There should be a good electrical
contact between this conduit and ground (Earth).
2. Keep the work and electrode leads as short as possible. Tape the leads together where
practical.
3. Be sure the torch and earth leads rubber coverings are free from cuts and cracks that
allow welding power leakage
4. Keep earth lead connection to work in good condition – Clean area on workbench where
earth clamp is situated on a regular basis.
Input Connections
Make sure the voltage, phase and frequency of input power is as specified on machine rating
plate located at rear of machine.
Have a qualified electrician provide suitable input power as per national electrical codes. Make
sure machine is earthed / grounded.
Make sure fuse or circuit breaker is correct rating for machine. Using fuses or circuit breakers
smaller than recommended will result in ‘nuisance’ shut off from welder inrush currents even if
cutting at low amperages.
Failure to follow these instructions can cause immediate failure within the welder and void
machines warranty.
Turn the input power OFF at the mains switch & fuse box before working on this equipment.
Have a qualified electrician install & service this equipment.
Allow machine to sit for 5 minutes minimum to allow the power capacitors to discharge before
working inside this equipment. Do not touch electrically live parts
The Plasma 60HF
Amp supply. It comes with a 3 metre mains cable attached.
Connect wires according to national coding.
Brown wire – Live
Blue wire – Live
Black Wire - Live
Green/Yellow Wire – Earth (Ground)
Plasma Cutters require a 415V 3 Phase 50/60Hz supply. It requires an 12.5
7
Connecting to a mains electrical supply
THIS MACHINE IS OF AN INDUSTRIAL SPECIFICATION AND MUST BE
FITTED TO A 16AMP 415V MAINS INPUT
Connecting to an Engine Driven Generator
If connecting this Plasma Cutter to an engine driven generator please
ensure the following
Minimum Generator KVA Output – 13.5 KVA continuous
Generator to be fitted with AVR (automatic voltage regulation)
DO NOT USE ON A GENERATOR WITHOUT AVR
Connecting to a generator without the above minimum requirements will in-
validate your warranty.
8
Connections for Plasma 60HF
Rear Machine connections
Fig 1
1. Air pressure regulating knob
This regulates the air pressure as displayed in gauge on front of machine.
To adjust pressure pull knob upwards and turn to adjust pressure, once correct
pressure is obtained press down knob to secure.
2. Air pressure input
Screw supplied PCL fitting into regulator ensuring no air leaks
You can also fit other connectors to suit your needs
nd
3. 2
Earth connection
This can be used to earth the machine to workbench if you are experiencing
interference from the HF – Sometimes required when using CNC automated machinery
- Not normally used
4. Mains input cable
Fit required plug as per your electrical installation
5. On / Off Switch
Turns machine On / Off
9
Front machine connections
Fig 2
1. Earth / Workpiece connector
Connect the earth lead (negative - ) to this connector.
Insert male connector into socket and twist clockwise until tight.
Secure other end of earth lead to Workpiece via the earth clamp.
2. Fuse holder – Pilot Arc Protection
Protection fuse for pilot arc start
3. Torch switch socket
Connect the torch switch plug (4 pin) and screw on retaining ring to secure
4. Pilot lead connector
Connect the ring terminal from torch. Un-screw retainer, fit ring terminal onto shaft and
refit retainer ensuring it is tight
5. Torch power connector
Connect the main torch cable by screw clockwise until tight.
10
Controls and Settings
Fig 3
1. Air pressure gauge
This shows the air pressure as set by regulator at rear of machine.
This should be set to 55PSI when the test gas button is activated.
2. Amperage control knob
This adjusts the amperage (cutting power) from 20 to 60 amps
Note: LED display will show cutting amperage when you are cutting
3. L.E.D amperage display
When cutting this shows the actual cutting amperage, this allows the machine to be
calibrated to BS if required by your company
4. Test Gas / Cutting selector switch
When in the up position this is test gas mode, when setting air pressure switch to test gas
so you obtain actual air flow cutting pressure
When in the down position this is cutting mode, you can now start cutting
5. Auto / Standard switch
When in the down position this is in standard cutting mode, this is the normal operating
position for plasma cutting with a hand held and machine type torch
When in the up position this is in auto mode, this is for special applications when using
automated machinery. Not normally used
11
Operating machine
SAFETY PRECAUTIONS
WARNING!
ELECTRIC SHOCK CAN KILL
Do not touch electrically live parts or electrode with skin or wet clothing.
Insulate yourself from work and ground
Always wear dry insulating gloves
WARNING!
FUMES AND GASES can be dangerous
Keep your head out of fumes & gases produced from welding.
Use ventilation or exhaust to remove fumes & gases from breathing zone and general
area.
WARNING!
WELDING SPARKS can cause fire or explosion
Keep flammable material away from work area.
Do not weld on containers that have held combustibles
WARNING!
ARC RAYS can burn
Wear eye, ear and body protection – Make sure work area is protected by proper shielding
to avoid injury to passers by.
12
Operating Machine
Please ensure all torch consumables are tight before use
1. Ensure machine has been setup as previously stated
2. Turn on the machine and the power light indicates and cooling fan is running
3. Set the function switch in the ‘test gas’ position, air will flow from torch head, now set the
air pressure in gauge using adjuster on regulator on rear of machine to 55PSI
Once the correct air pressure has been set press down the adjuster on air regulator and
set the function switch to the ‘cutting’ position
4. Ensure earth clamp is connected to workpiece or workbench ensuring a good clean point
of contact
5. Select cutting amperage knob to desired cutting power (the following guide lines will vary
in accordance to material grade, characteristics and user operation)
20 Amps for up to 6mm on mild steel
30 Amps for up to 9mm on mild steel
40 Amps for up to 12mm on mild steel
60 Amps for up to 17mm on mild steel
When cutting aluminium, alloys and stainless steel cutting thickness is reduced by
approximately 20%
6. Hold torch in starting position on work and press torch switch and the pilot arc will initiate
(blue flame from torch) , once the pilot arc is in contact with the workpiece it will sense
this and switch to main cutting power.
Once you come to the end of cut/workpiece the machine will sense this and turn off main
cutting power and re-start the pilot arc. If you have now finished cutting release torch
trigger and pilot arc will stop. Air will continue to flow from torch for a preset time to cool
torch consumables.
7. Getting correct amperage / cutting speed for desired job.
The combination of correct cutting amperage and travel speed can change per user, here
are some tips on obtaining optimum settings.
Blow back when cutting – If you experience blow back and the metal is not cut all the way
through, you either are traveling too fast or you need to increase the cutting amperage
Cutting arc is erratic and work is being cut all way through. You are traveling too slow or
cutting with too high amperage for work. What is happening is the machine is sensing
that there is no metal left to cut and turning off main cutting power and going back to pilot
arc mode and when you move again it senses more metal to cut and brings main cutting
power back in.
It can take a while to get used to plasma cutting if never done before. Experiment with
settings on some scrap material until you find the best amperage / cutting speed for user.
If you ever have any questions on settings call us and speak to one of our experienced
technicians who will be happy to help you.
13
Replacing torch consumables
WARNING!
ELECTRIC SHOCK CAN KILL
Please ensure machine is turned off before changing consumables
If cutting performance is poor you probably need to check / change the torch consumables.
To change the
1. Switch off machine
2. Ensure torch has cooled down to avoid burns
3. Unscrew the pink ceramic shroud
4. Remove the silver cutting tip
5. Check the condition of cutting electrode, replace cutting electrode if tip is worn 1-2 mm and
6. Fit new cutting electrode by screwing in and tweaking with pair of pliers – Do not over
7. Fit new cutting tip by screwing in and tweaking with a pair of pliers – Do not over tighten as
8. Refit pink ceramic cup by screwing on hand tight
9. Turn machine back on and continue cutting
plasma cutting consumables carry out the following procedure
end is concave
tighten as this will cause thread / torch head damage
this will cause thread / torch head damage
14
Maintenance
Routine and periodic maintenance
WARNING!
ELECTRIC SHOCK CAN KILL
Turn the input power OFF at the mains switch & fuse box and remove mains plug from socket
before working on this equipment.
Have a qualified electrician install & service this
Allow machine to sit for 5 minutes minimum after disconnection from mains power to allow the
power capacitors to discharge before working inside this equipme nt.
Do not touch electrically live parts
1. Periodically (3-6 months depending on use / environment), remove the side/top panels of
machine and clean out machine with a low pressure dry air line paying particular attention
to PC Boards, Fan blades and switchgear
Failure to maintain plant can void manufacturers warranty.
2. Inspect input and output cables & hoses for fraying and cuts, replace if damaged present
3. Keep cutting torch and earth cables in good condition
4. Clean air vents to ensure proper air flow and cooling
5. The fan motor has sealed bearings which requires no maintenance
Plasma cutting equipment.
15
FAULT DIAGNOSTICS
1. Power light not lit
Check machine on/off switch is in the ‘on’ position
Check Input power to machine
Check plug wiring
Check mains trip / fuses
2.
No output - Fan runs - Power light is lit
Check torch connections are secure and torch switch operation, try replacing plasma
cutting torch
3. No output - Power light is lit - Warning light is lit
Welding application may have exceeded recommended duty cycle, allow machine to
cool down until the warning light goes out.
4. No output – Power light is lit – Air at torch tip – No Pilot Arc
Check condition of torch consumables and replace if worn
Check pilot arc protecting fuse on front panel of machine and replace if blow – If fuse
keeps blowing contact R-Tech for repair / replacement torch
Please ensure machine is switched off before checking fuses
Check for water in water trap at rear of machine, if water is present, drain air
compressor, clean water out of air lines, empty water trap by pressi ng water release
button on bottom of air regulator water trap. Fit new consumables as per instructions
earlier in this manual
HF PCB Failure – Contact R-Tech for repair
5. Machine keeps overheating - Warning light is lit on machine
Check if fan is running – if not contact R-Tech for repair
Check the cooling vents for obstruction, blow out machine with clean dry low pressure
air supply. Check for adequate ventilation around machine
6. Erratic cut – Torch spitting when cutting
Check torch consumables and replace if necessary as per instructions earlier in this
manual
Check if correct amperage for thickness of metal, if to slow travel speed or to much
cutting power, increase speed of cut or reduce cutting amperage. (When machine
senses no metal left to cut it will switch of main cutting power and switch on HF pilot
arc, this is the HF pilot arc restart)
Water contamination in torch head, Check for water in water trap at rear of machine, if
water is present, drain air compressor, clean water out of air lines, empty water trap by
pressing water release button on bottom of air regulator water trap. Fit new
16
consumables as per instructions earlier in this manual
Plasma Torch Consumables parts list
R-Tech Torch Spares
Plasma 60HF
Electrode P40-EL
Cutting Tip 1.0mm 40 Amp P40-CT1
Ceramic Cup P40-CC
Spring, Stand off P40-SS
Torch Head –Hand Held P40-THH
Torch Complete Hand Held 6M P40-6MHHT
Plasma 60,80,100 HF
Electrode P60100-EL
Cutting tip 0.8mm 30 Amp P60100-CT08
Cutting tip 1.1mm 60 Amp P60100-CT11
Cutting tip 1.3mm 80 Amp P60100-CT13
Cutting tig 1.5mm 100 Amp P60100-CT15
Shroud P60100-SH
Torch Head hand held P60100-THH
Torch Head Machine P60100-THM
Torch Complete 6m Hand Held P60100-6MHHT
Torch Complete 6m Machine type P60100-6MMTT
Part No.
Plasma torch switch
17
TS1
Wiring Diagram
18
19
Loading...