R-TEC Automation RTMDC25, RTMDCQ28, RTMDC35 User manual

FEATURES

DC Tubular Motors

RTMDC25, RTMDCQ28, RTMDC35

DC Tubular Motors - DC motorized shades are ideal when designing a new

home, motorizing an existing home or planning a commercial project.

Available in three motor sizes, DC wired shades are maintenance free and the AC power supply adapter keeps installation costs to a minimum.

They offer a low voltage, easy-to-use and program solution to suit a large range of applications, including narrow applications, setting this tubular motor apart from other options.

2-Way RF

Communication

Adjustable

Speed

Leveling

Control

Preferred

Upper / Lower

Limit Settings

Favorite Position

Quiet

Operation

1

TABLE OF CONTENTS

Technical Data / Pack Contents 3

Installation 3

Safety 4

Wiring 5

Power Options

Functional Overview 6

P1 Button

Programming / Initial Set Up

7 - 8

Pair Motor with Controller Check Motor Direction Set Limits

Adjusting Limits

9

Adjust Upper Limit Adjust Lower Limit

Adding or Removing Controllers & Creating Group Channels

Using Motor P1 Button Using a Pre-Existing Controller

Favorite Positioning

11

Set a Favorite Position Send Shade to Favorite Position Delete Favorite Position

Adjusting Motor Speed

12

Increase Motor Speed Decrease Motor Speed

10

Step & Roller Mode

Enter Step Mode Enter Roller Mode (Default)

Sleep Mode

14

Enter Sleep Mode Exit Sleep Mode

Troubleshooting

15

13

2

COMPLIANCE STATEMENT

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

• This device may not cause harmful interference.

• This device must accept any interference received, including interference that may cause undesired operation.

TECHNICAL DATA / PACK CONTENTS

PRODUCT SPECIFICATIONS

Parameters Value for 25 mm Value for 28 mm Value for 35 mm

Voltage 12 V DC

Torque 1.1 Nm 2.0 Nm 3.0 Nm

Max. Run Time 10 min.

Speed 40 RPM (Adj. to 30 or 20) 28 RPM (Adj. to 24 or 20) 28 RPM (Adj. to 24 or 20)

Radio Frequency 433.92 MHz

Amps 0.83 A 1.25 A 1.67 A

Sound Level ~46 DB ~44 DB ~53 DB

Limit Switch Type Electronic

Temperature Working Range 32º F - 140º F (0º C - 60º C)

PACK CONTENTS

1. DC Tubular Motor

2. Instruction Manual

RTMDC25 25 mm 11.77" 0.98" 6.25"

RTMDCQ28 28 mm 17.41" 1.13" 6.25"

RTMDC35 35 mm 18.07" 1.38" 6"

Motor

Size

Motor

Length

Motor

Dia.

Motor Cable

Length

Motor

Diameter

Motor Length

Motor Cable Length

INSTALLATION

Installation Instructions:

3

SAFETY

WARNING

Incorrect installation can lead to serious injury and will void manufacturer's liability and warranty.

CAUTION

• Do not expose to moisture or extreme temperatures.

• Do not allow children to play with this device.

• Use or modiﬁcation outside the scope of this instruction manual will void warranty.

• Installation and programming to be performed by a suitably qualiﬁed installer.

• For use within tubular shades.

• Ensure correct crown and drive adapters are used for the intended system.

• Keep antenna straight and clear from metal objects.

• Do not cut the antenna.

• Use only R-TEC Automation

• Before installation, remove any unnecessary cords and disable any equipment not needed for powered operation.

• Ensure torque and operating time is compatible with end application.

• Do not expose the motor to water or install in humid or damp environments.

• Motor is to be installed in horizontal application only.

• Do not drill into motor body.

• The routing of cable through walls shall be protected by isolating bushes or grommets.

• Ensure power cable and antenna are clear and protected from moving parts.

• If cable or power connector is damaged, do not use.

®

hardware.

IMPORTANT SAFETY INSTRUCTIONS TO BE READ PRIOR TO OPERATION

• It is important for the safety of persons to follow the enclosed instructions. Save these instructions for future reference.

• Persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge should not be allowed to use this product.

• Keep remote controls away from children.

• Frequently inspect for improper operation. Do not use if repair or adjustment is necessary.

• Keep motor away from acid and alkali.

• Do not force the motor drive.

• Keep clear when in operation.

Do no dispose of in general waste.

Please recycle batteries and damaged electrical products appropriately.

4

WIRING

POWER OPTIONS

DC motors are powered from a 12V DC power source. Rechargeable Battery Pack, Battery Tube or Power Supplies are available, with a variety of quick connect extension cords. For centralized installations, power supply range can be extended with 18/2 wire (not available through R-TEC Automation

• During operation, if the voltage drops to less than 10V, the motor will beep 10 times to indicate a power supply issue.

• Motor will stop running when the voltage is lower than 7V, and it will resume again when the voltage is greater than 7.5V.

®

).

High Capacity Battery Pack

Solar Panel Battery Charger (use if using High Capacity Battery Pack option above)

Battery Tube

DC Power Supply

Item # Power Option Extension Cables Motor

RTMDCHCBP

RTMDCBT

High Capacity Battery Pack for 25/28 mm Motors (requires Battery Charger RTMLBC 12', .4 Amp, 12V)

Battery Tube for 25 mm DC Motors (requires 8 AA Li-ion Batteries - not included)

RTMLCXT48 48"

RTMLCXT96 96"

RTMDC25

RTMDCQ28

RTMDC25

RTMSOLAR2

RTMDC18/25 Power Supply for 25 mm DC Motors 5' RTMDCXT48 48" RTMDC25

RTMDC28/35 Power Supply for 28/35mm DC Motors 10 ½' RTMDCXT48 48"

Solar Panel Battery Charger (use if using High Capacity Battery Pack option above)

RTMDC25

RTMDCQ28

RTMDC35

IMPORTANT

Ensure cable is kept clear of fabric. Ensure antenna is kept straight and away from metal objects.

5

R-TEC Automation RTMDC25, RTMDCQ28, RTMDC35 User manual

Specifications and Main Features

Frequently Asked Questions

User Manual