RPS RS-RT04-C3, RS-RT06-P, RS-RT06-S, RS-RT04-P, RS-RT04-S User manual

1 Year Limited Warranty.

Dot Line Corp. warrants that if the accompanying product proves to be
defective to the original purchaser in material or workmanship within 1
year from the original retail purchase, Dot Line Corp. will, at its option,
either repair or replace same without charge (but no cash refund will be
made).
What you must do to enforce the warranty: You must deliver, mail or
ship the product together with the original bill of sale, to:

Dot Line Corp. 9420 Eton Ave., Chatsworth, CA 91311

Phone [phone] Fax [phone].

Limitation of Liability and Remedies: This warranty is void if any

defects are caused by abuse, misuse, negligence or unauthorized
repairs. All liability for incidental or consequential damages is specifically
excluded. The company shall have no liability for any damages due to
lost profits, loss of use or anticipated benefits, or other incidental,
consequential, special or punitive damages arising from the use of, or
inability to use, this product, whether arising out of contract, negligence,
tort, or under any warranty, even if the company has been advised of the
possibility of such damages. The Company’s liability for damages in no
event shall exceed the amount paid for the product. The Company
neither assumes nor authorizes anyone to assume for it any other
liabilities.
Some states do not allow for the exclusion of incidental or consequential
damages, so the above exclusion may not apply to you. This warranty
gives you specific legal rights and you may have other rights which vary
from state to state.

These Instructions are for RS-RT04/ Series Wireless Shutter Releases.
Illustrations may vary. Specifications are subject to change.
Revised March 2008.

RS-RT/04 Series

Wireless Shutter Release

Instructions

Features:

This device allows a Digital SLR camera to be released
from a distance up to 85 ft away, depending on conditions,

Included in the Package:

1) Transmitter with telescoping
antenna with battery

1) Receiver requires 2 “AAA”
batteries-not included

1) Hook and Loop Tape

Installing the Batteries

• Install 2 “AAA” batteries into the
back of the receiver. Be careful to
match the diagram.

• Install the 23A battery provided in the
transmitter by sliding the battery cover
to the side and then removing the
cover. The negative (-) terminal goes
against the spring contact.

RPS Studio Products are Marketed exclusively by:

Dot Line Corp. 9420 Eton Ave.

Chatsworth, CA 91311

818-700-9997 • Fax [phone]

www.dotlinecorp.com

Product Made in China © Dot Line Corp. 2007

Setting the DIP Switches

• Make certain that the dip switches on
the transmitter match the dip switches
on the receiver. The factory default has
all 4 switches set to OFF. Up to 16
different combinations can be set.

DIP Switches must be set the
same on both transmitter and
receiver

Activating the Units

• Extend the antenna on the
transmitter. The transmitter is
activated by the button. There is
no separate on/off switch on the
transmitter.

• Activate the receiver by
depressing the pushing the switch
to the on position (towards the
cord). The light will blink rapidly
indicating the unit is starting up.
After that the light will only flash
when it receives a signal from the
transmitter.

• Insert the receiver end plug into
the remote socket of the camera.
Consult your camera’s manual for
its location.

Please note: Additional models for various
other cameras wiil be released as they
become available.

For Canon 5D, 10D, 20D
30D (3 Pin Style)

Using your Remote Release

• To trigger the camera, depress

Green LED Prefocus

the transmitter button slightly until
the LED turns green (The LED will
turn green on the transmitter and
the receiver) This is your prefocus
light. To release the shutter,
continuing pressing the transmitter
button until the LED turns red. The
LED will turn red on both the

Red LED Shoot

transmitter and the receiver.

If the camera is set to the “B”
Position, you can press and hold
the shutter release button for 3
seconds, and the shutter will
remain open. Press it again and the
shutter will close.

Range of Use

The wireless transmitter uses RF (Radio Frequency) waves
to transmit the signal to the receiver. As a result the
effective distance can vary greatly depending upon the
environmental conditions, including walls, obstructions, etc.
In addition, wireless networks, cell phone towers, and some
cordless phone systems can interfere with the signal. If the
effective range if decreased due to environmental conditions
try another location. This is not considered a defect.
As the batteries weaken, your effective range may
decrease. Try using fresh batteries.

For Nikon D100, D200
D2X (10 pin Style)

- 2 -

For Canon EOS, Pentax
and other cameras which
use a 3.5 Mini Plug

Deactivating the Unit

• To turn off the power on the receiver, press the orange
button once. The red LED will stop blinking. There is no
on/off power switch on the transmitter.

• If the unit will not be used for some time, remove the
batteries.

- 3 -