ROYCEED WT110 User Manual

02
INTRODUCTION
Our TPMS product uses reliable integrated circuit, according diffusible silicon sensing principle and RF communication principle, which makes the product perform well, easy to install and work stably. This type product is o ne of the most advanced TPMS products in the world.
FORE WO RD
According t o statistics, about 70% of all traffic accidents are caused by tire blo wout, while the figure would be hig her to 80%. The statistic s of SAE shows that there are over 260000 accidents caused by tire blowout or leak, and about 75% tire fault is caused by low pressure or leak. US governmen t requires developin g TPMS pro duct to reduce traffic accidents. NHTSA in US develop a proje ct that truck, bus, car and SUV with gross w eight less than 4500 Kg should be installed TPMS product to improve traffic safety. It is because long time driving under abnormal tire pressure o r temperature that rubbing abr asion of tire beco me rapid to cause tire blowout. The aim of TPMS is to notice the driver to keep tires in correct condition when driving . Just as the figures showed below, fig ure B and C result in stress centralization that it makes the tire shoulder be abraded rapidly if under low pressure condition while the centre part be abraded rapidly if under high pressure.
Three d ifferent inflation condition of tire
A. Normal
B. low pressure C high pressure
03
This product m akes you drive safe ly. If there's any abn ormal, it can send the message immediately including the value of the press ure and temp erature , which make you drive reliably.
The LCD, LED buzzer and keys will turn off if Key is off, but the receiver still m onitors the tires, if some abnormal message is received, the informati on will be recorded and displayed on LCD whe n Key is on.
,
3. M essage of each tire displays in turn
When Key is on and all tires are under normal condition, t he message of each tire is displayed in turn every five sec onds twic e. Right front tire right rear tire left rear left f ront . It will stay at right front tire if no war ning mes sage received. If there is a warning m essage and is on, the warning message is displayed, if there are 2 or more warning messages, warning messages are displayed in turn.

tire tire
Key
OPERATIONOPERATION
This product can monitor the pressure and the temperature of ea ch tire. It will warn the driver if any tire is abnormal.
a) Reading fu nction: to check the of each tire; b) Set function: to set the standard value of p ressure ,u n it
temperature;
c) Warning functio n: L
low power of transmitter ,
no signal .
information
of pressu re and
ow pressure warning, high pressu re warnin g, leakage
warning, hi gh temperature warning, warning
warning
1. Key introduction
Enter key Read the information of each tire or confirm the settings. UP key: select transmitter and increase DOWN key: Set and decrease
:
.
.
Receiver oper ation
UP key
DOW N key
Ente r key
2. Power on
The L CD shows as the following figure when power on, which means the receiver is doing self checking and all LED on. The self checking will be finished in 3 seconds and the LCD will display the information if Key is on.
04 05
PSI
Bar
F
C
b) Leakage : the buzzer and yellow LED
is on; the value of pressure and temperature, the tire icon of the
transmitter are displayed and the icon of leaking is flashing; the buzzer will stop buzzing if any key is pressed. T he warning message of each tire will be displayed in tu rn if more than one tire is under abnormal condition.
warning turns on for 6 beeps
warning
c) Low pressure : t he buzze r and red
LED is on; the v alue of pressure and temperature, the tire icon of the transmitter are displayed and the icon of low pressure alarming is flashing; the buzzer will stop buzzing if any ke y pressed. The warning message of each tir e will be displayed in turn if more than one tire is under ab normal condition.
warning turns on for 6 beeps
warning
is
OPERATIONOPERATION
4. Displaying in turn fini shed:
a) If some warning message is received , the warning message will
be displaye d
b) Any key press will stop turn -by-turn displaying except UP key if
there is warning mes sage.
5. Warnings
a) H igh pressure warning: the buzzer turns on for 6 beeps and re d
LED is on; the value of pressu re and temperature, the tire icon o f the transmitter ar e displayed and the icon of high pressure i s flashing; the buzzer will stop buzzing if a ny key is down. The warning message of each tire will b e displayed in tur n if more than one tire is under abnormal condition.
warning
06 07
d) High temperature : the buzzer and red
LED is on; the va lue of pre ssure and temperature, the tire icon o f the
transmitter are displayed a nd the ic on of high temperature
alarmingisflashing;thebuzzerwillstopbuzzingifanykeyispressed.
warni ng turns on for 6 beeps
warning
f) No signal : the buzzer and yellow LED is
on; the v alue of pressure and temperature , the tire icon of the
transmitte r are di splayed and the ic on of no signal is
flashing; t he buzzer will stop buzzing if any key pressed. the
warning turns on for 2 beeps
warning
is
Note: Only if the well inflated tire icon is displayed with green LED on,
warning message of each tire will be displayed in turn if more than one tire is under abnormal condition
it means no warning. The w arning or messages are displaye d in turn if there are more than one transmitter are under ab norma l condition.
warning
6. Manual reading
The warning message can be displayed automatically when any tire is under a bnormal condition. Enter key will select the tire to display its information.
OPERATION
7. Set up a transmitter
Press the DOWN key for 3 seconds, SET will be displayed, then press the Enter key to enter next step. When P-B is displayed , press th e UP key to make L-C displayed, then press Enter key to select right front tire and F01 displayed. Select the tire to be set u p




The warning message of each tire will be displayed in turn if more than one tire is under abnormal condition.
e) Low power of transmitter : the buzzer and
yellow LED is on; the value of pressure and temperature, the tire i con of the transmitter are displayed and the icon of low power is flashing; the buzzer will stop buzzing if any key pressed. The warning message of each tire will be displayed in turn if more than o ne tire is under abnormal condition.
warning turns on for 6 beeps
warning
is
OPERATION
08 09
press UP key to select the tire (for example F01 ) which will be exchanged the position, then press DOWN key to select the second tire (

for
example F 03 )which will exchange its position with the first one and press Enter key to conduct the exchange. If there is other tir es positi on ex ch a nge, do as the above.Press Enter key to exit the funct ion when END is displaye d.
9. Standard p ressure setting
The pre-set standard pr essure is 2.4Bar. Keep on press DOWN key for 3 seconds to let SET be displayed, th en press Enter to make 'P-B be displayed. If E-P is disp layed by pressing UP key, press Enter key with front tires icons and previous set value (like 2.4Bar) displayed, press UP key to make the figure increase while DOWN key decrease,
  
OPERATIONOPERATION
by UP key and m ake the new one send out RF signal, senso r's ID (lik e
E6 5A -- on the ID card) will be displayed after th e receive r received the information, t hen pres s Enter k ey to accept it with --- displayed. After tha t, press UP key t ill END displayed and press En ter key t o finish se tting up.



8. Exchange tire s position
Press DOWN key for 3 seconds and SET will be displayed, then press Enter key and P-B be displayed. If S-P is displayed by pressing UP key, press En ter key with right front tire icon and F01 displayed,

 

10 11
11. Temperature unit setting
The pre-set temperature unit is . Press DOWN key for 3 seconds to let SET be displayed, then press Enter key to make P-B be displayed. If C-F is displayed by pressing UP key, press Enter key to enter the temperature unit setting menu. Press UP key to change between displayed. Press Enter key to confirm your selection.

 


OPERATION
press Enter key to acce pt the va lue with rear tires icons displayed instead of front tir es. To set the rear tires valu e as sam e as front tires. Note: S tandard t ire pressure is the cold tire pressure recommended by manufacture the tire.
10. Pressure unit setting
The pre-set pressu re unit is Bar . Press DOWN key for 3 seconds to let
SET be displayed, then press Ener key to make 'P-B be display ed. Press Enter key to enter the pressur e unit me nu. Press UP key to change between Bar and P SI , press Enter key to accept your sele ction.


  
OPERATION
12 13
INSTALL ATION
Transmitter Installation
Ascrew B metallic washer C electronic unit Dvalve E rubber washer
    
F metallic washer G collar nut H v alve cap I installation pin
 
1) Tak e out of the produc t from the p ackage, and the transmitter is a whole
unit. It's needed to unscrew the valve cap (H) and the collar nut (G), take off the me tallic washer (F), and loose the screw (A).
2) Put the electronic unit (C) and valve (D) through th e valve hole of the
hub. Then put the meta llic washer (F) on the valve, tighten the collar nut (G ). (Fig-1)
INSTALLATION
14 15
3) Put the in stallation pin (I) into the radial boring of the valve and tighten colla r nut (4 0.5 Nm torque.) (Fig-2)
4) Press the e lectronic unit lightly into the deep well of the hub in order to let the electronic unit lie flat in the drop center. Apply the thread glue on screw (A) then tighten it the with 4 0.5 N m torque.(Fig-3)
5) Now the electronic unit had tightly leaned against the valve. (Fig-4)
6) Tig hten the valve cap and complete the installation. (Fig-5)
7) Ins tall tire o nto the wheel. Att ention must be paid to ensure that the tire bead does not press against the w heel electronic unit! Inflate the tire and do t he balance. Make sure there is no air leak.
8) Do the same thing as above to the other tires.
±
±
Warnings Table
01
02
03
04
05
06
SN
Warni ng type
Value th reshold
The pressure is higher than standard about 40%
Thepressuredecreaseover0.2Barin20seconds
The pressure is lower than standard about 25%
The temperature of tire is over 80
The power of any transmitter is less than 2.4V
Missingsometransmittermessagesover20minutesafter ON

High pres sure wa rni ng
Leakage warning
Lowpressure warning
Hi gh t em pe ra tu re wa rnin g
Lo w p owe r of t r ans m itt er wa rn ing
No signal warning
Unit conversion
Pressure unit conversion: 1kg/cm2= 0.98Bar= 14.2PSI = 98.0665kpa Air pressure equals 1.03327 kg/cm2 Temperature unit conversion: C=5/9 F-32 F=9/5C+32 Note: C means Celsius; F means Fahrenheit

TECHNICAL SPECIFICATIONS
INSTALLATION
Receiver Installa tion
The receiver should be attached to the dash surface using double-side tape, wh ere the d river can see it easily.
Correctly c onnect the cable:
Red wire 12V connect to the elec tric cell White wire ON Black wire GND

GND
BATTER Y
BLACK
RED
KEY ON
WHITE
16 17
Technical Specifications
A) Receiver:
Power supply: DC 12V 3V Working temperature: -40 ~ +85 LCD -20 ~ +70
B) Transmitter:
Power supply: DC2.1-3.6V Working frequency: 433.92MHZ


Iddle currency: <18mA Working frequency: 433.92MHZ
SERVICE AND WARRANTY
2. C hange or Modify the product without any authorization
3. D amage caused by wrong operations
4. R epair without authority
5. Other da mage not be cause of des ign, technical, manufacturing and qual ity problem of the sy stem.;
6. U nder the extreme te mperature an d environment or in fluenc ed by corrosion and oxid ation.
7. The non-renewable parts suc h as b attery.
1. The data of ti re pres sure a nd tem perat ures d isplayed by our TPMS are just for wa rning, so the data itself cannot pr event the car from occurring accident.
2. O ur TPMS is a safety system that m onitors the c onditio ns of tire pressure and temperature. When the con dition is abnormal, o ur TPMS warns the driver to take precautions so as to prevent traffic ac cident. But it doesn 't mean usual checking of the tire is no longer necessary. Drivers should follow the Car User Manual
to take usual check of the tire condi tion. If the ac cident is caused by the abrasion, crack , break of the tire or perfora tion into the t ire, our TPMS is not responsible for it.
3. T his system complies with part 15 of FCC Rules. Opera tion mu st be subje ct to t h e following two conditions: (1) This system does not cause harmful interference, and (2) this system can operate normally in any interference received, inc luding interference th at
Important Statement
Warranty Clause Guarantee:
Warranty Date
How t o get the war ranty s ervice
Exception to Warranty:
In the period of warranty, our dealer and the service center can repair this pro duct to corre ct the flaw of the m aterial, design or wo rkman ship in the reasona ble tim e on busine ss. The product can b e changed if we think necessary .
Guarantee period is 12 mo nths counted from the purchase d ay.
User must show
1. Pro duct part of influence
2. Inv oice that name and date could be read clearly
3. Warranty card.
1. Normal abrasion

SERVICE AND WARRANTY
SERVICE AND WARRANTY
18 19
Working temperature: - 40 ~ +125 Pressure dete cting range 0-3. 5Bar Pressure detecting 0.1Bar T emp erature detecting range 40 ~ +125 T emp erature detecting a 2 at


 
 
accuracy at 25
ccuracy 25

condition, the vehic le can be allowed to drive on.
3. The warranty information and product features may be modified without notice.
SERVICE AND WARRANTY
SERVICE AND WARRANTY
may cause undesired operation.
4. Thi s syste m has been t ested t o comply with the limits for a Class B Digital Device , specified in the A rticle 1 5 of the FCC rules. These lim its are desi gned to provide reasonable protection against harmful interfer ence in a resid ential installa tion.
5. This system complies with all European Electromagnetic Compatibility Regulations (95/54/EC and EN 300 220-1).
6. Th is system complies with Natio nal Regulations for auto
elec tronic products, and meets the EMC requirements and the requirements made by Radio-Communicati on Administration for low-power consu mption transmitters and receivers.
The w arranty clause must be explaine d under the law . If the law allows, for the pro duct itself, we has the on ly responsibi lities to exchange goods, supply t he sam e goods, ma intenan ce the goods or pay the cost for the same quantity of the product, for the service itself, we has the only responsibility to supply the serv ice or pay the
cost for the s ame service.
1. Op eration is not sugges ted during dri ving.
2. On ce bein g warned, th e driver should imm ediate ly slow down and stop the veh icle to have the vehicle checked and repaired . Only when tire pressure an d temperature return to norma l
Legal obligation
Attention:
20 21
Warning:
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference,
(2) this device must accept any interference received,
including interference that may cause undesired
operation.
to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference in a
residential installation. This equipment generates,
uses and can radiate radio frequency energy and,
if not installed and used in accordance with the
This equipment has been tested and found
particular installation. If this equipment does
instructions, may cause harmful interference to
radio communications. However, there is no
guarantee that interference will not occur in a
receiver.
—Increase the separation between the equipment and
SERVICE AND WARRANTY
SERVICE AND WARRANTY
22
23
reception, which can be determined by turning
the equipment off and on, the user is encouraged
to try to correct the interference by one or more of
the following measures:
—Reorient or relocate the receiving antenna.
—Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician
for help.
by the party responsible for compliance
could
void the user's authority to operate the equipment.
Changes or modifications not expressly approved
cause harmful interference to radio or television
WARRANTY CARD
Product Informat ion
Dealer Informat ion
Installation Record
Product Name
Product Colour
Dealer Name
Dealer Address
Sell Date
Dealer Signature
Installation Company
Installation Date
Product Model
Product Number
Telephone
Invoice Number
Zip Code
Installation Address
Installation Staff
WARRANTY CARD
User Information
Product Information
Dealer Information
User Name
Address
E-mail
Product Name
Product Color
Dealer Name
Dealer Address
Sell Date
Dealer Signature
Telepho n e
Zip Code
Product Model
Product Number
Telepho n e
Invoice Date
Zip Code
Warranty Card (ForCustomer)Warranty Car d
24 25
Loading...