RoyalTek BT Users Manual

RoyalTek

BT GPS mini (RBT-1000) User Manual V.1.5

FCC Compliance and Advisory Statement

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation.

The equipment has been certified to comply with the limits for a Class B computing device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed or used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by switching the equipment off and on. The user can try to correct the interference by the following measures:

1. Reorient or relocate the receiving antenna.

2. Increase the separation between the equipment and receiver.

3. Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.

4. Consult the dealer or and experience radio/TV technician for help.

Changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Content

1. Product Introduction ............................................................... 1

1.1. Overview.........................................................................................................1

1.1.1. Wireless GPS receiver: ........................................................................1

1.2. Main Features..................................................................................................1

1.3. Product Notification........................................................................................2

1.4. Application......................................................................................................2

2. Quick Start.............................................................................. 3

2.1. Control Switch, Power Jack & Antenna Port..................................................3

2.2. LED Display ...................................................................................................4

2.3. Hardware Features .......................................................................................... 5

2.3.1. Power Switch ....................................................................................... 5

2.3.2. Power Jack ........................................................................................... 5

2.3.3. External Antenna Port..........................................................................5

2.3.4. Bluetooth Status LED (Blue) ...............................................................5

2.3.5. GPS Status LED (Green) ..................................................................... 5

2.3.6. Battery Status LED (Red/Yellow)........................................................ 5

2.4. Getting Started ................................................................................................ 6

2.4.1. STEP 1: Charge the Battery................................................................. 6

2.4.2. STEP 2: Turn on Receiver and Wait for GPS Fix ................................ 6

2.4.3. STEP 3: Connect to Bluetooth-Enabled Devices.................................6

2.4.4. STEP 4: Use GPS Application ............................................................. 6

3. Installation .............................................................................. 7

3.1. Install PDA Software Application................................................................... 8

3.2. Install PC Software Application....................................................................10

3.3 Install Palm Software Application .................................................................13

4. Software Application User Manual for PDA ........................ 14

4.1. Connection Page ...........................................................................................14

4.1.1. Device Name...................................................................................... 14

4.1.2. Change ...............................................................................................14

4.1.3. COM Port...........................................................................................14

4.1.4. Connect ..............................................................................................15

4.1.5. Auto Scan ...........................................................................................15

4.1.6.Factory Reset: .....................................................................................15

4.1.7. Disconnect..........................................................................................15

4.2. Navigation Page ............................................................................................16

4.2.1. NMEA Mode / SiRF Mode ................................................................16

4.2.2. Degraded Mode.................................................................................. 16

4.2.3. Elevation mask...................................................................................16

4.2.4. DOP Mask..........................................................................................16

4.2.5. SBAS Mode ....................................................................................... 16

4.2.6. Default................................................................................................16

4.2.7. OK......................................................................................................16

4.3. Mode: ............................................................................................................17

4.3.1. Maximum Navigation Performance:..................................................17

4.3.2. Optimal Battery Use: .........................................................................17

4.3.3. Intelligent Switch:..............................................................................17

4.3.4. Manual Setting:..................................................................................17

4.4. Configuration ................................................................................................18

4.4.1. Change Password ...............................................................................18

4.5. About.............................................................................................................18

5. Software Application User Manual for PC ........................... 20

5.1. Application User Interface ............................................................................20

5.2. Connection Page ...........................................................................................20

5.2.1. Device Name...................................................................................... 21

5.2.2. Change ...............................................................................................21

5.2.3. COM Port...........................................................................................21

5.2.4. Connect ..............................................................................................21

5.2.5. Auto Scan ...........................................................................................21

5.2.6. Factory Reset: ....................................................................................22

5.2.7. Disconnect..........................................................................................22

5.3. Navigation Page ............................................................................................22

5.3.1. NMEA Mode / SiRF Mode ................................................................22

5.3.2. Degraded Mode.................................................................................. 22

5.3.3. Elevation mask...................................................................................23

5.3.4. DOP Mask..........................................................................................23

5.3.5. SBAS Mode ....................................................................................... 23

5.3.6. Default................................................................................................23

5.3.7. OK......................................................................................................23

5.4. Mode ............................................................................................................. 24

iii

5.4.1. Maximum Navigation Performance:..................................................24

5.4.2. Optimal Battery Use: .........................................................................24

5.4.3. Intelligent Switch ...............................................................................24

5.4.4. Manual Setting:..................................................................................24

5.5. Configuration: ...............................................................................................25

5.5.1. Change Password ...............................................................................25

5.6. About.............................................................................................................26

6. Palm Software Application User Manual ............................. 27

6.1. Connection Page ...........................................................................................27

6.1.1. Device Name:.....................................................................................27

6.1.2. Change: ..............................................................................................27

6.1.3. COM Port:..........................................................................................27

6.1.4. Connect: .............................................................................................28

6.1.5. Factory Reset: ....................................................................................28

6.1.6. Disconnect: ........................................................................................28

6.2. Navigation Page ..........................................................................................29

6.2.1. NMEA Mode / SiRF Mode:..............................................................29

6.2.2. Degraded Mode:.................................................................................29

6.2.3. Elevation mask:.................................................................................. 29

6.2.4. DOP Mask:.........................................................................................29

6.2.5. SBAS Mode: ......................................................................................29

6.2.6. Default: ..............................................................................................29

6.2.7. OK:..................................................................................................... 29

6.3. Mode: ............................................................................................................30

6.3.1. Maximum Navigation Performance:..................................................30

6.3.2. Optimal Battery Use: .........................................................................30

6.3.3. Intelligent Switch:..............................................................................30

6.3.4. Manual Setting:..................................................................................30

6.4. Configuration: ...............................................................................................31

6.4.1. Change Password:..............................................................................31

6.5. About:............................................................................................................ 31

7. GPS Test on PDA ................................................................. 32

7.1. Execute GPS Demo Program........................................................................32

7.2. GPS Demo Screen.........................................................................................32

7.2.1. GPS Port: ...........................................................................................33

7.2.2. Baud Rate:.......................................................................................... 33

7.2.3. About:................................................................................................. 33

7.2.4. Action:................................................................................................33

7.2.5. ...................................................................................................33

7.3. Cold/Warm/Hot Start ....................................................................................33

7.4. About.............................................................................................................34

7.5. Next Screen...................................................................................................34

8. GPS Test on PC..................................................................... 35

8.1. Execute GPS Demo Program........................................................................35

8.2. GPS Demo Screen.........................................................................................35

8.2.1. GPS Port: ...........................................................................................35

8.2.2. Baud Rate:.......................................................................................... 35

8.2.3. About:................................................................................................. 35

8.2.4. Action:................................................................................................36

8.2.5. ...................................................................................................36

8.3. Cold/Warm/Hot Start ....................................................................................36

8.3. About.............................................................................................................37

8.4. Next Screen...................................................................................................37

9. Explanation of GPS Terminology ......................................... 38

11.. PPrroodduucctt IInnttrroodduuccttiioonn

1.1. Overview

BT GPS mini (RBT-1000)-A compact combo-device

with Bluetooth and GPS technology

1.1.1. Wireless GPS receiver:

BT GPS mini, a multi-wireless GPS consumer product, is the smallest

and most cost-effective Bluetooth GPS receiver in the world. It has a

built-in replaceable and rechargeable Lithium-ion battery just using the same

battery of Nokia 6100 cell phone. With the dimension of 70(L) x 41(W) x

23(H) mm and weight only 60g, making it an ideal solution to carry

everywhere.

BT GPS mini is both precise and durable. Its 12-channel receiver allows for

continuous tracking of all visible satellites. By wearing this Bluetooth GPS

around your neck and having your bluetooth integrated with any kind of

mobile device, such as PDA or Notebook, it will provide your exact

location almost anywhere.

1.2. Main Features

 Twelve parallel channels

 Support 2D / 3D information

 Hot/ Warm/ Cold start time: 8/ 38/ 45 seconds

 RF MCX connector for external GPS antenna

 Support standard NMEA-0183 at 57600 bps baud rate

 Compatible with Bluetoth devices with SPP (Serial Port Profile)

 Three LEDs showing Bluetooth, GPS and battery status

 Rechargeable and replaceable Lithium-ion battery, also compatible with

Nokia 6100 cell

 Power switch

1.3. Product Notification

 Operating temperature range -20 ºC to +60 ºC

 Charger operating temperature range 0 ºC to +40 ºC

 Battery Storage temperature range -20 ºC to +50 ºC

 Lithium-ion battery lasts more than 8 hours in continuous operation

mode.

 Humidity range up to 95% no condensing

1.4. Application

 Navigation

 Automotive Vehicle Tracking

 Personal Positioning

 Geographic Surveying

 Sporting and Recreation

 Consumer wireless GPS

 Cellular Phone

22.. QQuuiicckk SSttaarrtt

2.1. Control Switch, Power Jack & Antenna Port

Power Switch

Power Jack

External Antenna

Port

2.2. LED Display

Battery Status GPS Status Bluetooth Status

• Blinking Blue light indicates Bluetooth in connection

• Green light grows indicates power on

• Blinking Green light indicates GPS position fixed

• Yellow light indicates charging

• Blinking red light indicates low power

2.3. Hardware Features

2.3.1. Power Switch

Power ON / Power OFF

2.3.2. Power Jack

The power jack allows you to connect to either a DC (included) or AC

power charger to recharge the internal battery.

2.3.3. External Antenna Port

If you have an external antenna with a male MCX connector (available

separately), you can use it instead of the BT GPS mini receiver’s internal

antenna. Simply plug your external antenna into the antenna port.

2.3.4. Bluetooth Status LED (Blue)

Flashing - Bluetooth is on and ready to transmit.

2.3.5. GPS Status LED (Green)

Flashing - Position is fixed.

Steady light – Device is on but position is not fixed.

2.3.6. Battery Status LED (Red/Yellow)

None - Battery has adequate power supply.

Red - Power is low. Charging immediately is required.

Yellow - Connected to power charger, charging.

LED off - Battery is fully charged.

2.4. Getting Started

2.4.1. STEP 1: Charge the Battery

1. Before you use the Bluetooth GPS Receiver, the battery must be

charged. Connect the power charger to the power jack, and then plug

into an electrical outlet. As the device is charging, the Battery Status

LED will show a yellow light.

2. When the battery is fully charged, the Battery Status LED will turn

off. Unplug the device and remove the charger.

2.4.2. STEP 2: Turn on Receiver and Wait for GPS Fix

1. The GPS Status LED will initially show a steady green light to show

that the position has not been fixed yet.

2. After the position is fixed, the GPS Status LED will be showing

flashing green. Now you are ready to connect to your

Bluetooth-enabled mobile device and use your GPS application.

2.4.3. STEP 3: Connect to Bluetooth-Enabled Devices

1. From your Bluetooth-enabled mobile device, perform a Bluetooth

device discovery. Refer to the user documentation for your

Bluetooth-enabled device for instructions.

After connection is created between Bluetooth-enabled device and

Bluetooth GPS, the LED will show flashing blue light.

Note: If it is needed to type in Pin code during configuration, please Key in

“ 0000”.

2.4.4. STEP 4: Use GPS Application

1. Load your GPS mapping or routing software, along with the

corresponding maps of the areas that you are occupying or plan to

travel to.

2. Start the application. Make sure the application is set for the COM

port that your Bluetooth-enabled mobile device will use for serial

communication. Now you should be ready to use your GPS

application as directed by the user documentation that came with the

software. More configurations may be necessary.

3. Refer to the following software application user manual to set up the

parameters of the device via Bluetooth radio.

33.. IInnssttaallllaattiioonn

The Main Menu of Installation CD shows as above.

 Click the Software for Windows 2000/XP; Software for Windows 98SE/ME

to install the PC software application.

 Click the Software for Pocket PC 2002; Software for Pocket PC 2003 to

install the PDA software application.

 Click the Software for Palm OS to install Palm software application.

 Click the User Manual to open the user manual of Bluetooth GPS.

 Click the View Our Website to link our http://www.RoyalTek.com, please

make sure your PC connects to Internet first.

 Click the Browse CD Contents to open the explorer to browse the files within

the CD.

3.1. Install PDA Software Application

Before you click the “Software for Pocket PC 2002; Software for Pocket PC

2003” to install the PDA software application from CD, you have to

synchronize the PDA and your system. Then the following window will show

in your system as below:

Click “Yes>” to continue. Or click ”No” to select the other destination to

install, or “Cancel” to give up installation.

Click “ OK” to complete the installation.

+ 32 hidden pages