Royal Sovereign RSL-380 User Manual 2

14

RSL-380 Laminator

OWNER'S MANUAL

1 1. WARRANTY

Royal Sovereign International warrants the equipment sold is free from defects in material
and workmanship for a period of One (1) year for Parts and Labor from the date of
installation, excluding lamination rollers which are warranted for Six (6) months. This
warranty is extended only to the original purchaser. This warranty is the only warranty
made by Royal Sovereign International and cannot be modified or amended. Royal
Sovereign’s sole and exclusive liability and the customer’s sole and exclusive remedy
under this warranty shall be, at Royal Sovereign’s option, to repair or replace any such
defective part or product. These remedies are only available if Royal Sovereign’s
examination of the product discloses to Royal Sovereign’s satisfaction that such defects
actually exist and were not caused by misuse, neglect, attempt to repair, unauthorized
alternation or modification, incorrect line voltage, fire, accident, flood or other hazard.

The warranty made herein is in lieu of all other warranties, expressed or implied, including
any warranty or merchantability or fitness for a particular purpose. Royal Sovereign will not
be liable for personal damage or personal injury (unless primarily caused by its
negligence), loss of profit, or other incidental or consequential damages arising out of the
use or inability to use this equipment.

This warranty specifically does not cover damage to laminating rollers caused by knives,
razor blades, or any sharp objects or abrasives, or failure caused by adhesives, or
damage caused by lifting, tilting and/or any attempt to position the machine other than
rolling on the installed castors or feet on even surfaces, or improper use of the machine.
Warranty repair or replacement by Royal Sovereign or its authorized Reseller(s) does not
extend the warranty beyond the initial one year period from the date of installation.
Unauthorized customer alterations will void this warranty.

LIMITED WARRANTY

RS Holland B.V.

Columbusstraat 25 - 3165 AC Rotterdam,
The Netherlands
E-mail : [e-mail]

[e-mail]

RS International Australia PTY. LTD.

30 Prime Drive, Seven Hills, NSW 2147, Australia
TEL : [phone]
FAX : [phone]
E-mail : [e-mail]

CORPORATE HEADQUARTERS

Royal Sovereign International Inc.

2 Volvo Drive, Rockleigh, NJ 07647 U.S.A.
TEL : [phone] FAX : [phone]
E-mail : [e-mail]

Royal Sovereign Inc.

<Oversea Sales Office>

1001, World Meridian II, 426-5, Gasan-dong,
Geumcheon-gu, Seoul, 153-759, KOREA
TEL : [phone] FAX : [phone]
E-mail : [e-mail]

RS Canada Inc.

164 Oakdale Road, Toronto, Ontario M3N 2S5
CANADA
TEL : +1

) 416-741-8400 FAX : [phone]

E-mail : [e-mail]

Read all instructions carefully before use.

For any Customer Support needs please choose the

Customer Support tab on www.royalsovereign.com

Royal Sovereign International Inc.

www.royalsovereign.com

RSL-380

32

TABLE OF CONTENTS

1. INTRODUCTION

TOPIC PAGE

1. Introduction ......................................................................................................... 3

2. Package Contents .............................................................................................. 3

3. Safety Precautions............................................................................................... 4

4. Parts..................................................................................................................... 5

5. Features Guide..................................................................................................... 6

6. Operation Instructions ......................................................................................... 8

7. Film Loading and Threading ............................................................................... 8

8. Maintenance....................................................................................................... 11

9. Trouble Shooting Guide..................................................................................... 12

10. Specifications...................................................................................................13

11. Warranty........................................................................................................... 14

2. PACKAGE CONTENTS

Thank you for purchasing a Royal Sovereign RSL-380 Table Top Laminator. It has been
designed and manufactured to provide years of continuous service. For complete
operating and maintenance information please read this instruction manual thoroughly.
Upon receipt of your laminator thoroughly inspect the box, machine and all other contents.
It is imperative that any shipping damage is reported and a claim is filed with the delivering
carrier immediately upon receipt.

Preloaded Roll Films
(350mm

?/X?gW.h
?V/Xf?W.Yh

V/X?eW.Y?h
?V/X?W.Yhe

V/T.Y?he
?S@Uhf

W.R/X?he
?W.Y?V/Xhe
W.Y?eV/X?h

?W.Yf?V/Xh
?.Y?gV/h

75mic

?/X?gW.h
?V/Xf?W.Yh

V/X?eW.Y?h
?V/X?W.Yhe

V/T.Y?he
?S@Uhf

W.R/X?he
?W.Y?V/Xhe
W.Y?eV/X?h

?W.Yf?V/Xh
?.Y?gV/h

30m)

(14in

?/X?gW.h
?V/Xf?W.Yh

V/X?eW.Y?h
?V/X?W.Yhe

V/T.Y?he
?S@Uhf

W.R/X?he
?W.Y?V/Xhe
W.Y?eV/X?h

?W.Yf?V/Xh
?.Y?gV/h

3mil

?/X?gW.h
?V/Xf?W.Yh

V/X?eW.Y?h
?V/X?W.Yhe

V/T.Y?he
?S@Uhf

W.R/X?he
?W.Y?V/Xhe
W.Y?eV/X?h

?W.Yf?V/Xh
?.Y?gV/h

98.4ft

/X
N)X?hg
?31?hg
?N@Lhg

31hg
N@L?hf
?@1?hf
?@@?hf
?@@?hf
?@@?hf
?@@?hf
?@@?hf
?@@?hf
?@5?hf
J@H?hf

75hg
?J@Hhg
?75?hg
J(Y?hg
.Y

RSL-380

Owner's Manual

SPARE FUSE (250V / 15A

RHL-380

54

3. SAFETY PRECAUTIONS

Failure to comply with any of the following safety procedures could result in
serious injury. Please read the instructions carefully and keep for future reference.

1. Only a licensed electrician should install wiring and outlet for the laminator.

2. Ensure the unit is plugged into a properly grounded outlet with the correct voltage.

3. Keep hands and clothing (i.e. Neckties) away from rollers.The rollers are pinch points
that can trap body parts or clothing and cause serious injury.

4. Keep flammable and wet objects away from the machine.

5. Place machine on a level surface.

6. Avoid excessive sunlight, humidity and extreme temperatures.

7. Ensure the unit is turned off, cooled, and unplugged from the outlet prior to moving
and/or repairing.

8. Keep out of reach of children.

9. Only Royal Sovereign authorized maintenance and service technicians should make
repairs.

10. Do not attempt to laminate items that exceed total recommended material thickness

for the unit

11. When cleaning the machine, don't use flammable sprays or materials.

12. Do not touch the rollers when they are hot or place foreign objects inside the machine.

13. Do not cover the surface of the machine until the machine has completely cooled.

4. PARTS

1.Upper Film 2.Lower Film 3.Idle Bar

4.Hot Rollers 5.Feed Table 6.Paper Guide

7.Control Panel 8.Tension Knob 9.Power Switch

RSL-380

6

5. FEATURES GUIDE 6. OPERATION INSTRUCTIONS

Power Switch (1) - Located on the rear of

the machine. “I” (on) “0” (off). (Fig. 1)

Cross Cutter (2) - Used to cut off the
laminated web. (Fig. 1)

Feed Guide (3) -The feed guide permits
alignment of the item(s) to be laminated. To
position the adjustable guide, loosen the knob,
slide it to the desired position and tighten the
knob to secure the feed guide in place. (Fig.2)

Safety Shield (4) - It prevents entanglement

NOTE: If the safety shield is opened, the power

to the motor will turn off.

Film Shaft and Locking
Core Adapter (5) -

The film shaft holds the film supply on the
machine. The locking core holds and locks the
film on the shaft to prevent shifting. (Fig.3)

Film Tension Adjustment (6) - Allows the
operator to increase or decrease film web
tension. To increase the tension turn the knob
clockwise and to decrease tension turn the
knob counterclockwise. (Fig. 4)

Figure 1

Reverse the rollers to undo jams

and correct misfed documents

Run and stop the machine

Reduce roller speed

(1~10 speed settings)

Increase roller speed

(1~10 speed settings)

Laminate 25~38mic (1~1.5mil) film

Laminate 50~100mic (2~4mil) film

Laminate 125mic (5mil) film

Figure 2

Figure 3

Figure 4

7

25~38mic
(1~1.5mil)

50~100mic

(2~4mil)

125mic

(5mil)

98

1. Turn the laminator ON (I) located on the rear of the machine. (Fig. 1)

RSL-380

Figure 1

Figure 2

Figure 3

2. Choose appropriate laminating thickness and speed.

3. Do not begin laminating until the blinking light is steady (approximately 10 minutes).

4. Position the item to be laminated on the feed table.

5. Press the RUN button. The rollers will begin to turn, wait for heat line to disappear,
feed the item into the machine.

6. Stop the laminator when all of the items have completely exited the rear of the
machine.

Repeat the above steps until all of your lamination is completed. When lamination is
completed or the machine is not in use for an extended period of time turn the power off.

?
?
?
?
?
?
?
?
?
?
?
?

@@ ?
?J@@L?hg?
?7@@1?hg?
J@@@@Lhg?
7@@@@1hg?

?J@@@@@@L?hf?
?7@@@@@@1?hf?
J@@@@@@@@Lhf?

7@@@@@@@@1hf?
?J@@@@@@@@@@L?he?
?7@@@@@@@@@@1?he?
J@@@@@@@@@@@@Lhe?
@@@@@@@@@@@@@@he?

LOADING UPPER ROLL FILM

?
?
?
?
?
?
?
?
?
?

1.Slightly slide the shaft to the right and pull it out
from the machine.

NOTE: Stand by mode and auto power off mode

- Stand by mode: If no activity is made within 30 minutes after each use the machine
will automatically switch into stand by mode. (In stand-by mode the temperature will
decrease to 80~90°… (176~194°F) and the three film thickness setting indicators will
blink).

- Auto power off mode: If the machine is in stand by mode and no activity is
made for 60 minutes the machine will automatically power off.

- If any activity is made while in stand by or auto power off mode the machine
will return to it's previous settings.

7. FILM LOADING & THREADING

2.Take both lock core adapters off of the shaft

3.Insert one of the core adapters into the right end
of the film core. For film with poly-in (adhesive
side is inside the web), make sure the adhesive
side is facing upward.(Fig.3)

10

RSL-380

11

8. MAINTENANCE

4. Insert the film shaft into the roll of film
from the right side with the copper end last.
Align and insert the core adapter on the left
end of the film core

?
?
?
?
?
?
?
?
?
?
?
?

@@ ?
?J@@L?hg?
?7@@1?hg?
J@@@@Lhg?
7@@@@1hg?

?J@@@@@@L?hf?
?7@@@@@@1?hf?
J@@@@@@@@Lhf?

7@@@@@@@@1hf?
?J@@@@@@@@@@L?he?
?7@@@@@@@@@@1?he?
J@@@@@@@@@@@@Lhe?
@@@@@@@@@@@@@@he?

?
?
?
?
?
?
?
?
?
?

LOADING LOWER ROLL FILM

1. Repeat steps 1-5 to load the lower roll film.

2. Once the upper and lower film is on the shaft, pull the film from the top and roll
down to the bottom roll to make certain that the film is aligned properly. Then
tighten the lower locking core screws.

NOTE: If the film is not aligned properly exposed adhesive will adhere to the rollers

and may cause the film to jam.

FILM THREADING

Refer to Figure 6

1. Do not apply any cleaning fluids to the rollers. Certain fluids may damage the
rollers.

2. Do not clean rollers with sharp or pointed objects.

3. Use adhesive remover to clean resin off of the rollers.

4. Use a damp cloth with water to clean the body of the machine.

5. Store machine in a dry clean area

5. Center the film on the shaft and lock it in
place with the locking core adapters

6.Carefully return the film shaft back into place.

Figure 1

Figure 2

Figure 3

1312

RSL-380

Rollers do not operate
after the RUN/STOP
button is pressed

Roller is not heating

Poor Lamination

Problem Cause Remedy

10. SPECIFICATIONS

9. TROUBLE SHOOTING GUIDE

Description RSL-380

Power supply AC 100,200,220~240V 50 / 60Hz 120V 60Hz

Power consumption 1200W

Max laminating width 350mm / 14"

Film thickness 25~125 mic / 1~5mil

Max laminating speed 3m/min / 9.9ft/min

Ready time 10 min

Heating method Hot Roller

Driving motor DC geared motor

Temperature contro

l Digital(micom)

Speed control

10

settings

Transport type 4 Roller

Cooling system No

Side cutter No

Cross cutter Yes
Film alignment No
Hot lamination Yes

Cold lamination No

Reverse Yes

Dimensions (w

?/X?gW.h
?V/Xf?W.Yh
V/X?eW.Y?h
?V/X?W.Yhe

V/T.Y?he
?S@Uhf

W.R/X?he
?W.Y?V/Xhe
W.Y?eV/X?h
?W.Yf?V/Xh
?.Y?gV/h

d

?/X?gW.h
?V/Xf?W.Yh
V/X?eW.Y?h
?V/X?W.Yhe

V/T.Y?he
?S@Uhf

W.R/X?he
?W.Y?V/Xhe
W.Y?eV/X?h
?W.Yf?V/Xh
?.Y?gV/h

h) 550

?/X?gW.h
?V/Xf?W.Yh
V/X?eW.Y?h
?V/X?W.Yhe

V/T.Y?he
?S@Uhf

W.R/X?he
?W.Y?V/Xhe
W.Y?eV/X?h
?W.Yf?V/Xh
?.Y?gV/h

520

?/X?gW.h
?V/Xf?W.Yh
V/X?eW.Y?h
?V/X?W.Yhe

V/T.Y?he
?S@Uhf

W.R/X?he
?W.Y?V/Xhe
W.Y?eV/X?h
?W.Yf?V/Xh
?.Y?gV/h

320(mm) / 21.7"

?/X?gW.h
?V/Xf?W.Yh
V/X?eW.Y?h
?V/X?W.Yhe

V/T.Y?he
?S@Uhf

W.R/X?he
?W.Y?V/Xhe
W.Y?eV/X?h
?W.Yf?V/Xh
?.Y?gV/h

20.5"

?/X?gW.h
?V/Xf?W.Yh
V/X?eW.Y?h
?V/X?W.Yhe

V/T.Y?he
?S@Uhf

W.R/X?he
?W.Y?V/Xhe
W.Y?eV/X?h
?W.Yf?V/Xh
?.Y?gV/h

12.6"

Unit weight 30kg / 66.1Ibs

1.Safety cover is open

2. Power cord is not
plugged in

3.Machine is not turned on

Call your authorized
dealer

1. Film tension is
unbalanced.

2. Lower idler bar is not
located in proper
position

3.Wrong temperature/
speed setting

1. Check safety cover is
properly closed

2. Plug in the power cord

3. Turn the machine on

Call your authorized dealer

1. Adjust film tension

2. Push idler bar in proper
position

3. Follow manufacturers
recommended
temperature and speed