Royal Sovereign RSL2701U, RSL2701S User Manual

Page 1
OWNER'S MANUAL
RSL-2701U (for CANADA MODEL)
RSL-2701S (for USA MODEL )
Read all instructions carefully before use.
For any Customer Support needs please choose the
Customer Support tab on www.royalsovereign.com
Royal Sovereign International Inc.
www.royalsovereign.com
Page 2
TABLE OF CONTENTS
TOPIC PAGE
1. Introduction ..................................................................................................................................................... 3
2. Package Contents ............................................................................................................................................. 3
3. Safety Precautions ............................................................................................................................................ 4
4. Parts ................................................................................................................................................................. 5
5. Control Panel .................................................................................................................................................... 6
6. Features Guide .................................................................................................................................................. 8
7. Film Loading and Threading ............................................................................................................................ 9
8. Operation Instructions .................................................................................................................................... 13
9. Maintenance ................................................................................................................................................. 13
10. Trouble Shooting Guide ................................................................................................................................ 14
11.Specification .................................................................................................................................................. 15
12.Warranty ........................................................................................................................................................ 16
Page 3
TABLE TOP LAMINATOR
1. INTRODUCTION
Thank you for purchasing the Table Top Laminator. It has been designed and manufactured to provide years of continuous service. For high quality lamination, please read this instruction manual thoroughly. This manual will provide you with complete operating and maintenance information.
2. PACKAGE CONTENTS
Fuse
Film leader board Manual Core 4EA Dust cover
Core bolt 4EA
Sample roll film 2EA
Page 4
3. SAFETY PRECAUTIONS
Failure to comply with any of the following safety procedures could result in serious injury. Please read the instructions carefully and keep for future reference.
1. Only a licensed electrician should install wiring and outlet for the laminator.
2. Ensure the unit is plugged into a properly grounded outlet with the correct voltage.
3. Keep hands and clothing (i.e. Neckties) away from rollers.The rollers have pinch points that can trap body parts or clothing and cause serious injury.
4. Keep flammable and wet objects away from the machine.
5. Place machine on a level surface.
6. Avoid excessive sunlight, humidity and extreme temperatures.
7. Ensure the unit is turned off, cooled, and unplugged from the outlet prior to moving and/or repairing.
8. Keep out of reach of children.
9. Only authorized maintenance and service technicians should make repairs.
10. Do not attempt to laminate items that exceed total recommended material thickness for the unit
11. When cleaning the machine, don't use flammable sprays or materials.
12. Do not touch the rollers when hot.
Do not place any foreign obects inside the laminator.
13. Do not cover the surface of the machine until the machine has completely cooled.
14. You can laminate by single film when the switch in the left cover is “O”.
(Insure the machine drastically cold, press the button in the left cover be “ O ”, then you can laminate by single side. It is a damage for the paper to laminate by single side while the rollers up and low are heating all together.)
- Model applies RSL-2701S only for USA.
Page 5
4. PARTS
10
TABLE TOP LAMINATOR
1. Upper Film 2. Lower Film 3. Idle Bar
4. Hot Rollers 5. Feed Table 6. Paper Guide
7. Control Panel 8. Tension Knob 9. Power Switch
*10. (2701S model only) Single/Double Laminating Switch “O” (on) “I” (off).
* For Single-side Laminating.
Page 6
5. CONTROL PANEL
210-230 F
230-270 F
270-310 F
RUN/STOP
DOWN
270 ~310 ˚F
230 ~270 ˚F
210 ~230 ˚F
REVERSE
UP
Film Application Temperature
270 ~310 ˚F
Film Application Temperature
230 ~270 ˚F
Film Application Temperature
210~230 ˚F
Increase roller speed
(1~10 speed settings)
Reduce roller speed
(1~10 speed settings)
Reverse the rollers to undo jams and correct
misfed documents
Run and stop the machine
RSL-2701U
Page 7
TABLE TOP LAMINATOR
RUN/STOP
UP
25 - 38 mic
50 - 75 mic
100 - 125 mic
210-230 F
230-270 F
270-310 F
5 mil
2 - 4 mil
1 - 1.5 mil
125 mic
50-100 mic
25-38 mic
125mic
* (100~125mic)
50~100mic
* (50~75mic)
25~38mic
* (25~38mic)
REVERSE
DOWN
Film Application Thickness
125mic(100~125mic)
Film Application Thickness
50~100mic(50~75mic)
Film Application Thickness
25~38mic(25~38mic)
Reduce roller speed
(1~10 speed settings)
Increase roller speed
(1~10 speed settings)
Reverse the rollers to undo jams and correct
misfed documents
Run and stop the machine
* For Single side Laminating.
RSL-2701S
Page 8
6. FEATURES GUIDE
Power Switch Located on the rear of the machine. “I” (on) “0” (off). (Fig. 2)
Cross Cutter Used to cut off the laminated web. (Fig. 2)
Feed Guide The feed guide permits alignment of the item(s) to be laminated. To position the adjustable guide, loosen the knob, slide it to the desired position and tighten the knob to secure the feed guide in place. (Fig. 3)
Safety Cover Cover + Protect the hot rollers.
NOTE: If the safety cover is opened, this rollers stop turning.
Film Shaft and Locking Core Adapter
The film shaft holds the film supply on the machine. The locking core holds and locks the film on the shaft to prevent shifting. (Fig.
4)
Film Tension Adjustment
Allows the operator to increase or decrease roll film tension. To increase the tension turn the knob clockwise and to decrease tension turn the knob counterclockwise. (Fig. 5)
NOTE: - Excess tension on the top roll feed will cause upward
1
2
3
4
5
6
curl.
- Excess tension on the botton roll feed will cause downward curl.
- Tension should be adjusted until the laminated materials exit flat.
Figure 2
Figure 3
5
Figure 4
6
Figure 5
Page 9
7. FILM LOADING & THREADING
Figure 6
1. Slightly slide the upper film shaft to the right and pull it out from the machine. (Fig. 7)
TABLE TOP LAMINATOR
2. Take both lock core adapters off from the shaft. (Fig. 8)
Figure 7
Figure 8
Page 10
3. Insert one of the core adapters into the right end of the film core. For film with poly-in (adhesive side is inside the web), make sure the adhesive side is facing upward. (Fig. 9)
4. Insert the film shaft into the roll of film from the right side with the copper end last. Align and insert the core adapter on the left end of the film core. (Fig. 10)
5. Center the film on the shaft and lock it in place with the locking core adapters. (Fig. 11)
Figure 9
Figure 10
6. Carefully return the film shaft back into place. (Fig. 12)
10
Figure 11
Figure 12
Page 11
TABLE TOP LAMINATOR
LOADING LOWER ROLL FILM
1. Repeat steps 1-5 to load the lower roll film.
2. Once the upper and lower film is on the shaft, pull the film from the top and roll down to the bottom roll to make certain that the film is aligned properly. Then tighten the lower locking core screws.
NOTE: If the film is not aligned properly exposed adhesive will adhere to the rollers and may cause the film to jam.
FILM THREADING / WEBBING
1. Set the temperature and speed according to the Recommended Temperature and Speed section.
2. Remove the Front Table.
3. Pull down the upper film over the Safety Cover to the lower film; align and center the lower film to upper film. (Picture 1)
4. Rewind the upper film until the film aligns with the Safety Cover.
5. Thread the film over the Upper Idle Bar and underneath the Safety Cover and pull down until it drapes over both upper and lower hot rollers. (picture 2)
6. Carefully pull up the laminate from the lower roll up and drape it over top of the upper film (over the top hot roller). (picture 3)
7. Reinstall the Front Table and close the Safety Cover.
8. Insert and push the leader board into the hot rollers and press the Run button. (picture 4)
9. Press the Stop button when the leader board has completely exited the rear of the laminator.
10. Use the Cross-Cutter to remove the leader board.
11. Trim any excess film off of the leader board. The leader board can
be re-used.
Picture 1
Picture 2
Picture 3
Picture 4
11
Page 12
LAMINATING SINGLE SIDED (RSL-2701S USA Model only)
Press the switch into the location “SINGLE ”.
Figure 13
12
Page 13
TABLE TOP LAMINATOR
8. OPERATION INSTRUCTIONS
1. Turn the laminator ON (I) located on the rear of the machine. (Fig. 2)
2. Choose appropriate laminating temperature and speed. (Fig. 1)
3. Do not begin laminating until the blinking light is steady (approximately 8 minutes).
4. Position the item to be laminated on the feed table.
5. Press the RUN button. The rollers will begin to turn, and feed the item into the machine.
6. Insure the machine drastically cold, press the button in the left cover be “ O ”,then you can laminate by upper roller for single laminating.(It is a damage for the paper to laminate by single side while the rollers up and low are heating all together.)
- Model applies RSL-2701S only for USA.
7. The first paper is bad while OPP film laminating, please use a test paper first and then the second paper must keep the distance less than 15mm form the front one.
- Model applies RSL-2701S only for USA.
8. Stop the laminator when all of the items have completely exited the rear of the machine.
9. Adjust top + botton roll feed tension until lamination is flat.
(See film tension adjustment page 8.)
NOTE: Stand by mode and auto power off mode
- Stand by mode: If no activity is made within 30 minutes after each use the machine will automatically switch into stand by mode. (In stand-by mode the temperature will decrease to 80~90°C and the three temperature setting indicators will blink).
- Auto power off mode: If the machine is in stand by mode and no activity is made for 60 minutes the machine will automatically power off.
- If any activity is made while in stand by or auto power off mode the machine will return to it’s previous stage.
9. MAINTENANCE
1. Do not apply any cleaning fluids to the rollers cer tain fluids may cause damage.
2. Do not clean rollers with sharp or pointed objects.
3. Use a crepe rubber cleaning block to remove adhesive from rollers. Works best when rollers are hot.
4. Use a damp cloth with water to clean the body of the machine.
5. Store machine in a dry clean area.
13
Page 14
10.TROUBLE SHOOTING GUIDE
Symptom Cause Possible Solution
1.Safety cover is opened
Rollers do not operate after the RUN/
STOP button is pressed
Roller is not heating Call your authorized dealer Call your authorized dealer
2. Power cord is not plugged in
3. Front table is not on properly
4. Machine is not turned on
1. Check safety cover is properlyclosed
2. Plug in the power cord
3. Check installed properly
4. Turn the machine on
Poor Lamination
1. Film tension is unbalanced.
2. Lower idler bar is not located in proper position
3.Wrong temperature / speed setting
1. Adjust film tension
2. Push idler bar in proper position
3. Follow manufacturers recommended temperature and speed
14
Page 15
TABLE TOP LAMINATOR
11. SPECIFICATIONS
MODEL RSL-2701U RSL-2701S RSL-2701 RSL-2701S RSL-380S
Power supply AC120V 60Hz
Power consunmption 1450W 1500W
Max laminating width 685mm 380mm
Film thickness 25~250mic /1~10mil 25~125mic/1~5mil
Max laminating speed 2.5m/min 3m/min
Ready time 10min
Heating method Hot Roller
Driving motor DC geared motor
Temperature control Digital(micom)
AC100V 60Hz AC220~240V
50/60Hz
AC 220~240V 50/60Hz
Speed control Digital(10steps)
Transport type 4Roller
Cross cutter Yes
Single No Yes No Yes Yes
Hot
lamination
Dimensions
Double Yes
Reverse Yes
(w×d×h) 920×520×320mm 550×520×320mm
Unit weight 50kg 30kg
15
Page 16
11. WARRANTY
Royal Sovereign International warrants the equipment sold is free from defects in material and workmanship for a period of One (1) year for Parts and Labor from the date of installation, excluding lamination rollers which are warranted for Six (6) months. This warranty is extended only to the original purchaser. This warranty is the only warranty made by Royal Sovereign International and cannot be modified or amended. Royal Sovereign’s sole and exclusive liability and the customer’s sole and exclusive remedy under this warranty shall be, at Royal Sovereign’s option, to repair or replace any such defective par t or product. These remedies are only available if Royal Sovereign’s examination of the product discloses to Royal Sovereign’s satisfaction that such defects actually exist and were not caused by misuse, neglect, attempt to repair, unauthorized alternation or modification, incorrect line voltage, fire, accident, flood or other hazard.
All warranty claims must be filed through the authorized Royal Sovereign dealer or reseller through which the equipment was originally purchased. Model, serial number and date of delivery are required for all claims.
The warranty made herein is in lieu of all other warranties, expressed or implied, including any warranty or merchantability or fitness for a particular purpose. Royal Sovereign will not be liable for personal damage or personal injury (unless primarily caused by its negligence), loss of profit, or other incidental or consequential damages arising out of the use or inability to use this equipment.
LIMITED WARRANTY
This warranty specifically does not cover damage to laminating rollers caused by knives, razor blades, or any sharp objects or abrasives, or failure caused by adhesives, or damage caused by lifting, tilting or improper use of the machine. Warranty repair or replacement by Royal Sovereign or its authorized Reseller(s) does not extend the warranty beyond the initial one year period from the date of installation. Unauthorized customer alterations will void this warranty.
ROYAL SOVEREIGN INTERNATIONAL INC.
2 Volvo Drive Rockleigh, NJ 07647 USA TEL : +1) 800-397-1025 FAX : +1) 201-750-1022 E-mail : info@royalsovereign.com
RS HOLLAND B.V.
Industrieweg 6K, 4104AR, Culemborg, The Netherlands Tel: +31 (0)345 473 097 Fax: 31 (0)345 519 811 eu.sales@royalsovereign.com
RS CANADA INC.
1025 Westport Crescent, Mississauga ON L5T 1E8 TEL : +1) 905-461-1095 FAX : +1) 905-461-1096 TF: +1) 866 961-6673 E-mail : info-ca@royalsovereign.com
RS INTERNATIONAL AUSTRALIA PTY. LTD.
30 Prime Drive, Seven Hills, NSW 2147, Australia TEL : +61) 2-9674-2127 FAX : +61) 2-9674-2027 E-mail : salesaust@royalsovereign.com
16
Loading...