Royal Sovereign RSH-380 User Manual 2

14

RSH-380 Laminator

OWNER'S MANUAL

Read all instructions carefully before use.

For any Customer Support needs please choose the

Customer Support tab on www.royalsovereign.com

Royal Sovereign International Inc.

www.royalsovereign.com

RS International Australia PTY. LTD.

30 Prime Drive, Seven Hills, NSW 2147, Australia
TEL : [phone]
FAX : [phone]
E-mail : [e-mail]

CORPORATE HEADQUARTERS

Royal Sovereign International Inc.

2 Volvo Drive, Rockleigh, NJ 07647 U.S.A.
TEL : [phone] FAX : [phone]
E-mail : [e-mail]

Royal Sovereign Inc.

<Oversea Sales Office>

1001, World Meridian II, 426-5, Gasan-dong,
Geumcheon-gu, Seoul, 153-759, KOREA
TEL : [phone] FAX : [phone]
E-mail : [e-mail]

RS Canada Inc.

164 Oakdale Road, Toronto, Ontario M3N 2S5
CANADA
TEL : [phone] FAX : [phone]
E-mail : [e-mail]

RS Holland B.V.

Planetenweg 75 2132HM Hoofddorp, The Netherlands.
TEL : [phone]
FAX : [phone]
E-mail : [e-mail]

13. W ARRANTY

Royal Sovereign International warrants the equipment sold is free from defects in
material and workmanship for a period of One (1) year for Parts and Labor from the date
of installation, excluding lamination rollers which are warranted for Six (6) months. This
warranty is extended only to the original purchaser. This warranty is the only warranty
made by Royal Sovereign International and cannot be modified or amended. Royal
Sovereign’s sole and exclusive liability and the customer’s sole and exclusive remedy
under this warranty shall be, at Royal Sovereign’s option, to repair or replace any such
defective part or product. These remedies are only available if Royal Sovereign’s
examination of the product discloses to Royal Sovereign’s satisfaction that such defects
actually exist and were not caused by misuse, neglect, attempt to repair, unauthorized
alternation or modification, incorrect line voltage, fire, accident, flood or other hazard.

All warranty claims must be filed through the authorized Royal Sovereign dealer or
reseller through which the equipment was originally purchased. Model, serial number
and date of delivery are required for all claims.

The warranty made herein is in lieu of all other warranties, expressed or implied,
including any warranty or merchantability or fitness for a particular purpose. Royal
Sovereign will not be liable for personal damage or personal injury (unless primarily
caused by its negligence), loss of profit, or other incidental or consequential damages
arising out of the use or inability to use this equipment.

This warranty specifically does not cover damage to laminating rollers caused by knives,
razor blades, or any sharp objects or abrasives, or failure caused by adhesives, or
damage caused by lifting, tilting or improper use of the machine. Warranty repair or
replacement by Royal Sovereign or its authorized Reseller(s) does not extend the
warranty beyond the initial one year period from the date of installation. Unauthorized
customer alterations will void this warranty.

LIMITED WARRANTY

RSH-380

32

TABLE OF CONTENTS

1. INTRODUCTION

TOPIC PAGE

1. Introduction ......................................................................................................... 3

2. Package Contents .............................................................................................. 3

3. Safety Precautions............................................................................................... 4

4. Parts..................................................................................................................... 4

5. Control Panel........................................................................................................ 5

6. Film Loading and Threading ............................................................................. 6.7

7. Before Laminating................................................................................................ 8

8. Operation Instructions .................................................................................... 9.10

9. Recommended Temperature and Speed Settings ........................................... 11

10. Maintenance..................................................................................................... 12

11. Trouble Shooting Guide................................................................................... 12

12. Specifications...................................................................................................13

13. Warranty........................................................................................................... 14

2. PACKAGE CONTENTS

Thank you for purchasing a Royal Sovereign RSH-380 table top laminator. It has been
designed and manufactured to provide years of continuous service. For complete
operating and maintenance information please read this instruction manual thoroughly.
Upon receipt of your laminator thoroughly inspect the box, machine and all other contents.
It is imperative that any shipping damage is reported and a claim is filed with the delivering
carrier immediately upon receipt.

Owner's Manual

RSH-380

54

3. SAFETY PRECAUTIONS

4. PARTS

Failure to comply with any of the following safety procedures could result in
serious injury. Please read the instructions carefully and keep for future reference.

1. Only a licensed electrician should install wiring and outlet for the laminator.

2. Ensure the unit is plugged into a properly grounded outlet with the correct voltage.

3. Keep hands and clothing (i.e. Neckties) away from the roller. The rollers have pinch
points that can trap body parts or clothing and cause serious injury.

4. Keep flammable and wet objects away from the machine.

5. Place machine on a level surface.

6. Avoid excessive sunlight, humidity and extreme temperatures.

7. Ensure the unit is turned off, cooled, and unplugged from the outlet prior to moving
and/or repairing.

8. Keep out of reach of children.

9. Only Royal Sovereign authorized maintenance and service technicians should make
repairs.

10. Do not attempt to laminate items that exceed total recommended material thickness

for the unit

11. When cleaning the machine, don't use flammable sprays or materials.

12. Do no t touc h the r ollers when they are hot or place foreign objects inside the

machine.

13. Do not cover the surface of the machine until the machine has completely cooled.

5. CONTROL PANEL

< TEMPERATURE >
This button is for changing the temperature of upper and

lower rollers.
Press the up button to increase temperature or the down

button to decrease temperature.

[range 20

o

C(68 °F) through 150 oC(302 °F)]

< SPEED >
This button is used to change the speed of the rollers.
(Settings 1 - 9)

< T-CHECK >
To check current upper and lower roller temperature.
Display automatically returns to previous settings after 5 blinks.

< REVERSE >
This button is used to reverse the rollers to undo jams and

correct misfed documents.
< RUN/STOP >

This button is used to Run and Stop the machine.

1. FILM-UPPER

?@@?f
?@@?f

2. FILM-LOWER.

3. TENSION CONTROL KNOB.

4. TOP HOT ROLLER.

5. FRONT FEED TABLE.

6. CONTROL PANEL.

7. SAFETY SHIELD.

8. PRESSURE LEVER.

RSH-380

6

6. FILM LOADING & THREADING

< Film Threading >

1. Turn the power switch on (“I” position). (The Power
switch is located on the rear the unit)

2. Complete the steps in the "Loading Film" section.

3. Set the desired temperature.

4. Remove the Front Feed Table.

5. Pull down the upper film over the Safety cover to the
lower film; align and center the lower film to the
upper film and tighten the 2 lower bolt core
screws. (Figure 1)

6. Rewind the upper film until it aligns with the safety cover.

7. Thread the film over the Lower Idle Bar and underneath
the safety cover until the film rests on the upper
roller. Figure 2

8. Put the Front Feed Table back on and close the Safety
cover. Figure 3

9. Press the Run button and thread the film using the
Laminating Threading Card. Figure 4

< Thermal Film Loading & Threading >

Loading Film

1. Remove the upper and lower film shafts from the
machine and load the films (do not tighten the
core screws at this time)

2. To load the top film, insert 1" core as shown on
Figure 1 (Note the direction that the film is wound)

3. Insert the shaft as shown in Figure 2.

Figure 1

Figure 2

Figure 1

Figure 2

Figure 3

Figure 4

Figure 3

Figure 4

Figure 5

4. Insert the core plug on the left hand side. (Figure 3)

5. Align and center the film and tighten the two core

screws. (Figure 4)

6. Repeat steps 2 through 4 to load the lower film.

(Please note the direction that the film is wound

for the bottom roll). (Figure 5)

7. Load the upper and lower film shafts on the machine.

7

98

7. BEFORE LAMINATING 8. OPERATING INSTRUCTIONS

1. Turn the laminator on, the power switch is located
on the rear of the machine.

2. Adjust the tension of the upper and lower films.
Clockwise to tighten and Counter
Clockwise to loosen.

3. Set the pressure lever to the "Laminating mode"

4. Choose appropriate laminating temperature by
pressing the "UP" or "DOWN" button.

5. When desired temperature is met an alarm will
sound and "READY" will appear on the
display.

6. Press the "RUN/STOP" button. (If rollers don't run
check that the safety cover is completely
closed).

7. Position the item to be laminated on the Front Feed Table.

8. Adjust the film tension or laminating speed if necessary.

9. Press the "RUN/STOP" button when your lamination is finished.

10. After finishing your work, set the pressure lever to the "Hard Board/6mm"

11. Turn the Power switch off.

NOTE:

* Stand by mode : If no activity is made within 30 minutes after each use the

machine will automatically switch to stand by mode.

* Auto power off mode : If the machine is in stand by mode and no activity is

made for 90 minutes the machine will automatically power off.

1. For High Quality Lamination

- Refer to the "Recommended Temperature and Speed Settings" section before
laminating.

- The upper and lower film tension must be the same.

2. Changing Roll film.

- While laminating, if the roll film needs to be replaced, press the 'RUN/STOP'
button .
Once the rollers stop, cut the upper and lower film, remove and replace with new
rolls of film.

3. After lamination

- “Hot Spots” on the rollers may occur when the machine is idle. To help prevent
“Hot Spots” you must run the sample paper between the front rollers and stop the
machine while the sample paper is in between the rollers. You must leave the
sample paper in this position until you laminate again.

- After laminating with Thinflex™,use “Cleaning Paper” to clean the rollers.

RSH-380

RSH-380

1110

9. RECOMMENDED TEMPERATURE AND SPEED SETTINGS

speed

4~5

3~4

2~4

4~5

2~3

2~4

2~3

Function

25~38mic
(1~1.5mil)

75mic(3mil)

100mic(4mil)

250mic(10mil)

Temperature

100~110 oC

(212~230

o

F)

100~110

o

C

(212~230

o

F)

110~115

o

C

(230~239

o

F)

120~125

o

C

(248~257

o

F)

130~135

o

C

(266~275

o

F)

1) The cross cutter is located on the rear exit table
of the machine.

2) After lamination, move the cutter approximately

to the center of the application at the
desired point of detachment (

Figure 1).

3) Grasp film with one hand, press the cutter
downward into he application and slide it
first to one end of the application, then to
the other end to complete the cut

(Figure 2 & 3).

Paper

80 g/m

2

Paper(both side can be used)

120g/m

2

200g/m

2

color paper

80g/m

2

Paper(both side can be used)

120g/m

2

200g/m

2

color paper

80g/m

2

Paper(both side can be used)

120g/m

2

200g/m

2

color paper

80g/m

2

Paper(both side can be used)

120g/m

2

200g/m

2

color paper

< Using Cross Cutter >

Figure 1

Figure 2

Figure 3

1312

RSH-380

Rollers do not operate
after the RUN/STOP
button is pressed

Roller is not heating

Result of lamination is
waved.

Result of lamination is
not clear

Symptom Possible Cause Possible Solution

1.Safety cover is opened.

2. Power cord is not
plugged in

Call your authorized
dealer

1. Film tension is
unbalanced.

2. lower idler bar is not
located in proper
position

1. Temperature is lower or
speed is higher than
recommended

1. Check to make sure the
safety cover is closed.

2. Check the power cord.

Call your authorized dealer

1. Adjust film tension by
rotating tension handle

2. Push idler bar up

1. Adjust speed and
temperature

10. MAINTENANCE

12. SPECIFICATIONS

1 1. TROUBLE SHOOTING GUIDE

1. Do not apply any cleaning fluids to the rollers, certain fluids may cause damage.

2. Do not clean rollers with sharp objects, use a rubber gum eraser to clean resin off
of the rollers.

3. Use a damp cloth with only water to clean the body of the machine.

4.Store machine in a dry clean area.

Description RSH-380

Power supply AC 100, 200, 220

W2@6K?e?W.?g
?W.M?I46K?O.Y?g
?.Y?e?I4@0Yh

240V 50/60Hz 120V 60Hz

Power consumption 1500W

Max laminating width 380mm / 15"

Film thickness 25~250 mic / 1~10mil

Max laminating speed 5m/min / 16.4ft/min

Ready time 8min

Heating method Hot roller

Driving motor DC geared

Max temperature contro

l 150 OC / 302 OF

Speed control 9 settings

Transport type 4 Roller

Film core size 1", 2.25", 3"

Cross cutter Yes

Hot lamination Yes

Mounting thickness 6mm / 0.24"

Reverse Yes

Unit dimensions (w

?/X?gW.h
?V/Xf?W.Yh
V/X?eW.Y?h
?V/X?W.Yhe

V/T.Y?he
?S@Uhf

W.R/X?he
?W.Y?V/Xhe
W.Y?eV/X?h
?W.Yf?V/Xh
?.Y?gV/h

d

?/X?gW.h
?V/Xf?W.Yh
V/X?eW.Y?h
?V/X?W.Yhe

V/T.Y?he
?S@Uhf

W.R/X?he
?W.Y?V/Xhe
W.Y?eV/X?h
?W.Yf?V/Xh
?.Y?gV/h

h) 550

?/X?gW.h
?V/Xf?W.Yh
V/X?eW.Y?h
?V/X?W.Yhe

V/T.Y?he
?S@Uhf

W.R/X?he
?W.Y?V/Xhe
W.Y?eV/X?h
?W.Yf?V/Xh
?.Y?gV/h

690

?/X?gW.h
?V/Xf?W.Yh
V/X?eW.Y?h
?V/X?W.Yhe

V/T.Y?he
?S@Uhf

W.R/X?he
?W.Y?V/Xhe
W.Y?eV/X?h
?W.Yf?V/Xh
?.Y?gV/h

605(mm) / 21.5"

?/X?gW.h
?V/Xf?W.Yh
V/X?eW.Y?h
?V/X?W.Yhe

V/T.Y?he
?S@Uhf

W.R/X?he
?W.Y?V/Xhe
W.Y?eV/X?h
?W.Yf?V/Xh
?.Y?gV/h

27"

?/X?gW.h
?V/Xf?W.Yh
V/X?eW.Y?h
?V/X?W.Yhe

V/T.Y?he
?S@Uhf

W.R/X?he
?W.Y?V/Xhe
W.Y?eV/X?h
?W.Yf?V/Xh
?.Y?gV/h

24"

Unit weight 45kg / 99 Ibs

Carton dimensions (w

?/X?gW.h
?V/Xf?W.Yh
V/X?eW.Y?h
?V/X?W.Yhe
V/T.Y?he
?S@Uhf
W.R/X?he
?W.Y?V/Xhe
W.Y?eV/X?h
?W.Yf?V/Xh
?.Y?gV/h

d

?/X?gW.h
?V/Xf?W.Yh

V/X?eW.Y?h
?V/X?W.Yhe
V/T.Y?he
?S@Uhf
W.R/X?he
?W.Y?V/Xhe

W.Y?eV/X?h
?W.Yf?V/Xh
?.Y?gV/h

h) 800

?/X?gW.h
?V/Xf?W.Yh
V/X?eW.Y?h
?V/X?W.Yhe

V/T.Y?he
?S@Uhf

W.R/X?he
?W.Y?V/Xhe
W.Y?eV/X?h
?W.Yf?V/Xh
?.Y?gV/h

750

?/X?gW.h
?V/Xf?W.Yh
V/X?eW.Y?h
?V/X?W.Yhe

V/T.Y?he
?S@Uhf

W.R/X?he
?W.Y?V/Xhe
W.Y?eV/X?h
?W.Yf?V/Xh
?.Y?gV/h

650(mm) / 31.5"

?/X?gW.h
?V/Xf?W.Yh
V/X?eW.Y?h
?V/X?W.Yhe

V/T.Y?he
?S@Uhf

W.R/X?he
?W.Y?V/Xhe
W.Y?eV/X?h
?W.Yf?V/Xh
?.Y?gV/h

29.5"

?/X?gW.h
?V/Xf?W.Yh
V/X?eW.Y?h
?V/X?W.Yhe

V/T.Y?he
?S@Uhf

W.R/X?he
?W.Y?V/Xhe
W.Y?eV/X?h
?W.Yf?V/Xh
?.Y?gV/h

25,5"

Carton weight 57kg / 126 Ibs