Royal Sovereign ARP-1200DE, ARP-1200DM User Manual

Royal Centurian Inc.

ARP-1200M / ARP-1200DM / ARP-1200E / ARP-1200DE

OWNER’S MANUAL

MANUAL DEL PROPIETARIO

PORTABLE AIR CONDITIONER

ACONDICIONADOR DE AIRE PORTÁTIL

Read and retain these instructions for future reference

For any Customer Support needs, please choose

the Customer Support tab on www.royalsovereign.com

PORTABLE AIR CONDITIONER

Model ARP-1200M / ARP-1200DM / ARP-1200E / ARP-1200DE

BEFORE USE

GENERAL SAFETY

• Only use in the upright position on a flat, level surface at least 20”/50cm from any object (fig 1 & 4).

• Do not place objects on the unit or restrict air inlet / outlet (fig. 2).

• Closely supervise children and pets while unit is in use.

ELECTRICAL SAFETY

• For indoor use only.

• Turn off and unplug the unit when it is not in use.

• Do not use in wet environments (fig 3).

• Do not pull the unit by the cord.

• If the supply cord is damaged, it must be replaced by an electrician or qualified person, to avoid hazard or injury.

FOR MAXIMUM EFFICENCY

• Do not exceed the recommended room size 400 sq. feet.

• Close doors and windows.

• Keep curtains or blinds closed during the sunniest part of the day.

• Keep filters clean.

• Once room has reached the desired conditions, reduce temperature and ventilation settings.

FIG.3

FIG.1 FIG.2

FIG.4

ARP-1200M / ARP-1200DM

ARP-1200E / ARP-1200DE

Front

1. Control Panel

2. Air outlet

3. Carrying handle

4. Caster

Back

5. Air filter

6. Air inlet

7. Exhaust air outlet

8. Cord storage &

power cord with LCDI breaker plug and reset buttons.

9. Water stopper / drainage point

PARTS

Accessories

10. Air Conditioner adaptor - for insertion over hose and into back of the air conditioner.

11. Window adaptor - for insertion over hose and into window spacer.

12. Exhaust hose

13. Extendable window spacer.

14. Drain tube for continuous drainage

15. Water tray

16. Remote control (for electronic type only)

1 2

ARP-1200M / ARP-1200DM

ARP-1200E / ARP-1200DE

INSTALLATION

Installation of the exhaust pipe

The unit is a portable air conditioner that may be moved from room to room. Please follow the steps for installation:

1. Feed the outward adapter through the extendable window spacer.

2. Screw the exhaust hose into the outward adapter.

3. Insert the window spacer into window gaps as shown.

Adjust its length if necessary.

4. Slide window across so that the spacer is held securely.

NOTE: Take care to maintain protection against intruders

NOTE: Install window vent vertically or horizontally depending on window style.

Window Spacer may be cut to fit. If window spacer does not fill opening completely a custom made spacer from your local home improvement store can be made.

Extendable window spacer

FIG.5

FIG.6

FIG.7

Outward Adapter

Mounting of the exhaust pipe

• Using only the hose provided, screw unit adapter to exhaust hose then clip the unit adaptor to the back of the air conditioner.

• Avoid kinks and bends in the exhaust hose as this will cause expelled moist air to build up causing the unit to overheat and shut down. (Fig 8 & 9 show correct position).

NOTE: For best results do not exceed a 45º angle.( Fig 10)

• The hose may be extended from 1-5 ft /300mm -1500mm but for maximum efficiency use the shortest straightest length possible. It is not recommended to exceed 5 feet for this will diminish the efficiency of the unit. See WARNING Figure 11

WARNING

The length of the exhaust pipe is specially designed according to the specification of this product. Do not replace or lengthen it with your own hose as this will cause the unit to malfunction.

FIG.8 FIG.9 FIG.10

FIG.11

Installation of the carbon filter

1. Remove the filter frame from the unit.

2. Separate the filter fixer from the filter frame.

3. Remove the active carbon filter from its plastic bag.

4. Insert the active carbon filter into the filter frame.

5. Fix the filter by reassembling the fixer to the filter frame.

6. Re-fit the filter frame inside the unit.

1. Power indicator

2. Fan operating indicator

3. Cooling operating indicator

4. 'Full water' indicator

5. Heating operating indicator (ARP-1200DM only)

6. Timer (1-8 hours) as well as ON/OFF Switch

7. Speed switch with options for - FAN, LOW COOL, HIGH COOL, LOW HEAT, HIGH HEAT.

8. Thermostat

OPERATION for mechanical unit

ARP-1200M/ ARP-1200DM

FIG.12

ARP-1200M / ARP-1200DM

ARP-1200E / ARP-1200DE

Turning ON/OFF

Set the TIMER to ON position for continuous operation (the unit will operate as long as it is not turned off). Power indicator comes on. To turn off the unit, turn the TIMER to the OFF position.

Setting function / ventilation speed

Cooling only models (ARP-1200M and ARP-1200E) Turn the speed switch to select required setting: LOW FAN, HIGH FAN, LOW COOL, HIGH COOL

Cooling & heating models (ARP-1200DM and ARP-1200DE) Turn the speed switch to select required setting: FAN, LOW COOL, HIGH COOL, LOW HEAT, HIGH HEAT

Setting temperature

Turn the THERMOSTAT to regulate the temperature desired: The cooling intensity increases clockwise..

Set timer

Set the TIMER to the desired operating time (1 to 8 hours). When the set time has been reached, the machine will shut off automatically.

NOTE: 1. To lengthen the compressor's life, when the unit is turned off wait at least 3 minutes before turning it back on.

2. The cooling system will turn off if the ambient temperature is lower than the set one. The ventilation, however,

keeps working on the set level. If the ambient temperature rises above the selected level, the cooling function will resume.

3. On the contrary, the heat will turn off if the ambient temperature is higher than the set one (still, the ventilation keeps working on the set level). As the ambient temperature drops below the selected level, the heating function will resume.

4. This machine is equipped with an ANTI-FROST function. While using the heating function in low temperatures, sometimes the heat will stop for a while in order to melt the frost. As this occurs, just wait for the heating function to resume.

FIG.13

FIG.14

Turning ON/OFF

Press ON/OFF button, the unit will start automatically. If the ambient temperature is

- Higher than 75 oF / 24 oC, the unit will work in cooling mode.

- Higher than 68 oF / 20 oC, but below or equal to 75 oF / 24 oC, the unit will work in ventilation mode.

- Below 68

F / 20 oC, the unit will work in heating mode (Only for units ARP-1200 DM/DE) Indicators of the functions in progress will be lit. *NOTE: The COMPRESSOR indicator will only light up when the compressor is in operation. The display window shows the ambient room temperature. To turn the unit off, press the ON/OFF button again.

Setting mode/function

Press MODE button to select required working mode: automatic, cooling, fan or heating, (heating is only available for DM and DE units). The indicator of your selected mode will be lit. Auto mode is factory preset at 75 degrees. When in auto mode(auto and cool light illuminated) the temp up and temp down buttons are disabled and you cannot set a desired temperature. If you want a desired temperature above or below 75 run unit in cool mode and set your desired temperature by pressing the temp up or temp down buttons.

OPERATION for electronic unit

Control panel

1. 'Heating operation indicator (For ARP-DM, ARP-DE)

2. Fan operation indicator

3. Cooling operation indicator

4. Automatic mode indicator

5. ' Set temperature' indicator

6. 'Room temperature' indicator

7. High ventilation indicator

8. Low ventilation indicator

9. Timer operation indicator

10. Sleep function indicator

11. Compressor operation indicator

12. Mode (function) option button

13. 'Temperature up' button

14. 'Temperature down' button

15. Speed (ventilation) button

16. Sleep button

17. Timer button (1~12 hours)

18. ON/OFF(power) button

19. Receiver

20. Display window

FIG.16

ARP-1200M / ARP-1200DM

ARP-1200E / ARP-1200DE

Setting temperature

Press the 'Temperature up' or 'Temperature down' button to regulate the temperature desired. The display window will show the temperature which you have set as you press the 'Temperature up' or 'Temperature down' button. Otherwise, it will always show the ambient temperature. The preset temperature of this machine is: 75 oF / 24 oC / for cooling, 68 oF / 20 oC for heating.

Setting ventilation speed

1. Press the SPEED button to choose the ventilation speed needed, high or low. The indicator of high or low

ventilation will light up at the same time.

2. If the unit is in AUTO mode, it will choose the ventilation speed automatically according to the ambient temperature (the related

indicators will light up: at this time, the speed switch is invalid).

Setting timer

1. Press the TIMER button to set the operating hours desired (1 to 12 hours, the timer indicator will light on).

When the set time has been reached, the machine will turn off automatically. The display window will show the hour(s) you set as you press the TIMER button. If the timer button is not pressed, the unit will work continuously.

2. By pressing the timer but without turning on the other functions, you can PRESET the time for the machine to start.

For example, if you press the timer to '2', the unit will start automatically after 2 hours.

Sleep function

1. By pressing the SLEEP button, the set temperature will increase 2 oF /1 oC / in the 1st hour, another 2 oF / 1 oC in the second hour,

then remains at that temperature.

2. By pressing the SLEEP button again, the temperature setting will return to the pre-selected one.

3. The unit will automatically turn off after the SLEEP function runs for 12 hours.

All the above functions can also be performed with the supplied remote control. The remote control requires 2 AAA batteries to operate.

FIG.17

+ 22 hidden pages