Royal Sovereign ARP-1000ES User Manual

Royal Centurian Inc.

PORTABLE AIR CONDITIONER

ACONDICIONADOR DE AIRE PORTÁTIL

Read and retain these instructions for future reference

For any Customer Support needs, please choose

the Support tab on www.royalsovereign.com

ARP- 1000ES

OWNER’S MANUAL

ARP-1000ES

PORTABLE AIR CONDITIONER

Model ARP-1000ES

INTRODUCTION

Thank you for choosing this air conditioner to provide you and your family with all of the "Home Comfort" requirements for your home, apartment, or office. This appliance can be moved from room to room and set-up in just minutes. It is multi-functional room air conditioner that offers you Conditioning, Dehumidify, and Independent Fan modes. This manual will provide you with valuable information necessary for the proper care and maintenance for your new appliance. Please take a few moments and read the instructions thoroughly. If properly maintained, your appliance will give your many years of trouble free operation.

Electrical Specifications

1. All wiring must comply with local and national electrical codes and be installed by a qualified electrician. If you have any questions regarding the following instructions, contact a qualified electrician.

2. Check available power supply and resolve any wiring problems before installation and operation of this unit.

3. For your safety and protection, this unit is grounded through the power cord plug when plugged into a matching wall outlet. If you are not sure whether the wall outlets in your home are properly grounded, please consult an electrician. Do not use plug adapters or extension cords with this unit.

WARNING - Make sure rubber plug is installed in drain port on bottom of the machine.

Improper handling can cause serious damage to the appliance. Read this manual carefully before operating the unit.

Do not cover the air outlet while in use.

Do not wet the housing or control panel.

Do not allow children to play with the controls or drop any objects into the outlet.

Always turn the unit off and remove the power plug from the socket when cleaning.

Do not place objects or let any person sit on top of the unit.

Do not attempt to remove any part of the casing unless by an authorized technician.

Use only the correct power supply AC 115V/60Hz.

Remove the plug from the socket if the unit is not being used for long period.

Do not operate the unit with damaged plug or loose socket point.

Make sure that the back of the unit is at least 4" or more from a wall. Do not place the unit in front of curtains or drapes.

WARNING

-If the power cord on this unit is damaged, it must be replaced by the manufacturer service agent or qualified electrician.

-This appliance is not intended for use by children.

ARP-1000ES

DESCRIPTION OF COMPONENTS

1. Control panel

2. Air outlet (Up-Down and Left-Right)

3. Front panel

4. Handle hole

5. Casters

6. Screen filter

7. Air intake (Evaporator)

8. Air intake (Condenser)

9. Air outlet (Heat exchange)

10. Water drain with rubber plug

1. Insert ends of exhaust hose into exhaust nozzle connector and exhaust hose connector by twisting clockwise until it stops.

2. Attach the exhaust hose connector onto the rear outlet of the unit and turn to the right.

3. Attach the exhaust nozzle to the window spacer with the 4 screws provided.

4. Connect the exhaust nozzle connector to the exhaust nozzle.

5. Extend the exhaust hose and close the window as far as possible trapping the exhaust nozzle as shown below .

6. Install rubber plug as shown below.

INSTALLATION INSTRUCTIONS

Connect exhaust hose assembly to the back of the unit. Extend hose to desired length and locate the exhaust nozzle through a window or

wall for ventilation. DO NOT add additional hose length. This will diminish the efficiency of the unit. Window spacer only comes in one size. Good for double

hung or slider window only.

EXHAUST ASSEMBLY AND INSTALLATION

Exhaust nozzle Exhaust nozzle connector Exhaust hose Exhaust hose connector

ARP-1000ES

Insert exhaust nozzle from rear. Attach screws from front.

Exhaust nozzle connection

rubber plug

POWER CONTROL

The power control turns the unit on and off.

WARNING CONTROL

Condensed water may accumulate in the unit. If the internal tank becomes full, the Warning Light will shine and the unit will not operate until the unit has been drained.

FAN MODE

When fan mode is selected the indicator light will shine yellow. Air is circulated throughout the room with no cooling.

NOTE: Unit does not need to be vented in fan mode.

MODE CONTROL

The Mode Control has three settings:

Cool Dehumidify Fan

The settings are adjusted with the Mode Control button. A light will indicate which setting is currently being used.

FAN SPEED CONTROL

The Fan Speed Control has 3 setting: High, Medium, and Low.

OPERATION

When running unit for the first time, make sure the LCD light on the GFI plug is green. If not press and the reset button on the plug.

Control panel

Warning Light

Power Control

Mode Control

Fan Speed Control

Timer On / Off

Display

Timer / Temp Set Control

DEHUMIDIFY MODE

When dehumidify mode is selected, the indicator light will shine orange. Air is dehumidified as it passes through the unit, without being in full cooling mode. The fan will operate in low or medium speed. Fan speed is not adjustable in dehumidify mode.

NOTE: The air exchange hose must vent outside the room thru a window as usual.

COOLING MODE

When cool mode is selected, the indicator light will shine green. During the cooling mode the air is cooled and hot air is exhausted to the outside air through the exhaust hose.

NOTE: The air exchange hoses must vent outside the room when using cooling mode.

TIMER / TEMP SET CONTROLS

Used for adjusting the timer and thermostat. The default display is room temperature. In cooling mode, when "+" or "-" button is pressed, the set temperature is displayed and may be adjusted. After 15 seconds the display will revert back to room temperature. Temperature is only adjustable in cool mode. The time is adjustable between 1~12 hours.

NOTE: By pressing both Timer / Temp set buttons at the same time, the display will toggle between Celsius and Fahrenheit.

TIMER

Auto turn off:

With machine in fan mode, press timer button to select number of hours you would like the unit to run in air conditioning mode until it automatically shuts off.

Auto turn on:

With machine powered off, press timer button to select number of hours until you would like the unit to automatically start running in air conditioning mode.

After switching the air conditioner off, you must wait 3 minutes before switching it back on again.

ARP- 1000ES

Power ON / OFF Button

Mode Button (Select A/C, Fan or Dehumidify)

Timer and thermostat Setting Buttons

A/C Fan Speed Button (High, Medium or Low)

Timer ON/OFF Button

LCD Screen

OPERATION

Fahrenheit / Celsius Selector

Air Conditioner Remote Control

The functions work the same as your air conditioner's touch controls.

TIMER PROGRAMMING

1. Press the button on the remote or the "Timer Setting" button on the control panel to turn on the Timer Function.

2. Press the or buttons on the remote or the

or - buttons on the control panel to set

the desired shut-off period.

3. The unit will shut off when the set time elapses.

DEHUMIDIFICATION OPERATION

Press the button on the remote or the "MODE" button on the control panel to select the dehumidify mode. When the dehumidify mode is on, the temperature buttons and the fan speed buttons do not function and the fan will operate on low or medium speed. The dehumidify indicator light will illuminate and stay solid while the unit is dehumidifying. When the humidity in the room is 50% or lower, the compressor will not run, the unit will not dehumidify, and the dehumidify light will blink. Remember, the exhaust hose does not need to be used in dehumidify mode.

+ 16 hidden pages