IT'S NOT OUT OF ORDER ----------------------------------------------------
ASSEMBLY PARTS ------------------------------------------------------------WARRANTY -----------------------------------------------------------------------15
13
14
14
- 2 -
y
ply
INSTRUCTION
Thank you for purchasing a Royal Sovereign Roll Laminator. It has been designed and
manufactured to provide years of continuous service in the professional environment.
To insure high quality lamination, please read this instruction manual thoroughly. This
manual will provide you with complete operating and maintenance information.
SAFETY PRECAUTIONS
The safet
followed before operating machine.keep this information for future refrence. Failure to.
com
1. To prevent the possibility of electrical shock, do not immerse machine in water or
permit liquids to spill inside.
2. Do not allow articles of clothing (neckties, scarves, papers, etc.) near front or rear
machine openings as they could get caught by rollers and be pulled inside, causing
personal injury.
3. Do not insert sharp objects into front or rear machine openings.Do not place anything
in feed tray openings of machine other than appropriate laminating materials or pouches
4. Do not attempt to laminate items that exceed total recommended material thickness.
5. Do not operate machine for any other purposes than its intended use.
6. Do not operate machine if electrical plug or power cord is damaged.
7. Turn off the power when unattended or not in use. Unplug machine before moving it or
when it is not in use for an extended period of time.
8. This machine is intended for indoor use only.
9. Do not alter or extend electric plug. Plug is configured for appropriate electrical supply.
10. The socket-outlet shall be installed mear the equipment and shall be easily accessible.
recommendations outlined in this section are to be read, understood and
any of the following safety procedures could result in serious personal injury.
- 3 -
g
g
y
CHARACTERISTIC
RS Roll Laminator Line is advanced laminators with time transcendental design, utilizing the
latest in laminatin
It is desi
an
thing at high speed,regardless of thickness of material and type of film.It is also designed
ned for you to set temperature and speed as necessary. Also you can laminate
technology.
for convenient use by anyone through the simple procedure of adjusting film tension in
accordance with the thickness of film and materials to be laminated.
SPECIFICATIONS
Description
Power Supply120V/60Hz
Power Consumption(Watts)1700
Max. Laminating Width(mm)1650(65")1650(65")
Laminating Thickness(micron)
Laminating Speed(mm/min)
Ready time(min)10
Heating MethodWarm Roller
Temp` Select
Temp`Control
Speed Control
Driving Motor
Transport Type
Cooling System
Hot Lamination
Photo Laminationyes
Mount Lamination
Reverse
RSC-1650H
25,50,75,80,100,…
5000(16.4ft/min)
9 step
digital
9 step (digital)
DC Geared Motor
2 Roller
no
no
yes(15mm)
yes
RSC-1650C
120V/60Hz
100
—
no
Stand-by mode
Power auto-off
Foot switchyes
Remote switch
Laminating Length Measurement
Laminating Paper Counting
Dimension(W×D×H,mm)
Unit Weight
Gross Demension(W×D×H,mm)
Gross Weight
1960×650×1210(77.2“×25.6”×47.4“)
2100×875×1250(82.7“×34.1”×49.2“)
no
no
yes
no
no
230Kg(500ibs)
300Kg(660ibs)
- 4 -
NAMES OF MAJOR PARTS OF MACHINE
5
12
1
7
11
3
4
6
2
8
9
10
13
NO
1
2
3
4
5
6
7
8
9
10
11
12
13
PART NAME
FRAME-GUIDE,PAPER
TAKE-UP SWITCH
TAKE-UP BOBBIN
IDLE BAR
TABLE-FRONT
HOT ROLLER
ASS'Y-STAND
CONTROL PANEL
PRESSURE LEVER
TENSION CONTROL KNOB
SAFETY COVER
FOOT SWITCH
REMOCON SWITCH
RSC-1650H
UPPER ROLLER
RSC-1650H
○
○
○
○
○
X
○
○
○
○
○
○
○
- 5 -
주름방지부
열판
주름방지부
열판
표시창
LCD
버튼부
K
SETTING UP FILM
COLD FILM
PAPER BAC
1. Set the glossy side of upper/lower film to face the heat.
( Glossy side is PET film and matte side is thermal polymer laminating film.)
2. Like picture 1, insert core into the left side of upper/lower film shaft.
3. Like picture 2 and 3, insert core into the right side of upper/lower film.
4. Like picture 4 and 5, adhere core closely.
(Make the right/left direction of fixing screw consistent.)
5. Locate film in the middle, and then fasten core fixing screw.
- 6 -
HANGING FILM
TAKE UP DEVICE
PAPER BACK
HOT ROLLER
PAPER BACK
COLD FILM
UPPER IDLE BAR
LOWER IDLE BAR
1. Set up cold film below the upper bar of the machine.
(Set the same as methord of the HOT film for protect paper of lower part)
2. Set the pressure lever to the 15mm, open mode.
3. Insert a piece of wide cardboard (guiding paper/carrier) between the rollers.
4. Pull the film from the upper roller passing over the upper idle bar to the upper roller and put it
on the upper roller.
5. Put the paper back of the film to the bobbin at take-up bar to rewind the paper back.
6. Allow some of the film with melted resin to stick to the Guiding Paper.
7. Place the film from lower shaft beneath the film from the upper roller which is already meiting.
and unwind films of both rollers 30~40cm(1~1.3ft) for loosing the tension.
8. Set the pressure lever to the 1mm.
9. Set speed at 1 and press the RUN button. The films will be fed into the machine and will come
out from the rear site of machine.
10. Check the status of lamination and place the pressure lever at lamination mode.
- 7 -
CONTROL OF ROLLER PRESSURE
***Methods of controlling pressure of the roller**
1. For setting, pull the pressure lever out and turn the lever to following the indication
2. OPEN/15mm(Board) : For laminating 15mm thick board (RSC-1650H/1650C)
3. 10~13mm(Board) : For laminating 10~13mm thick board
4. 5~7mm(Board) : For laminating 5~7mm thick board
5. 1mm(Hard Board) : For laminating 1mm thick board
6. Laminating : For laminating 32~250micron thick film
- 8 -
INSTRUCTIONS FOR CONTROL PANEL
We designed this machine standing by user’s convenience. You can manipulate speed and
temperature .
***Terms***
2
3
6
4
5
6
1
3
2
1
- 9 -
1. FUNCTIONS OF CONTROL PANEL
1
2
3
4
5
6
RUN/STOP BUTTON: Run or stop the rollers
SPEED BUTTON: Increase or decrease speed
LED OF SPEED : Display or speed
LED OF TEMP.
TEMP.BUTTON: Increase or decrease temperature
REVERSE BUTTON : To make the rollers run backward
: Display temperature
2.HOW TO USE BUTTONS
RUN / STOP BUTTON
1
Push the button in order to run rollers and push
button to stop it.
2
Push the SPEED button to increase the speed,push the speed
button to decrease the speed.
5
Push the TEMP. button to increase the temperature,push the
TEMP. button to decrease.
6
Stay pressing REVERSE button to have . The roller run backward.
SPEED BUTTON
TEMP. BUTTON
REVERSE BUTTON
RUN
REV
STOP
- 10 -
LAMINATING STEPS
1. Put cold roll film on upper bar.(Set the same as methord of the HOT film for protect paper of lower
part)
2. Pull COLD film, and fix it so that backside protecting paper can be wound on take-up mandrel
clockwise. (Revolve core to make protectingpaper tight a little bit.)
3. Set pressure lever at the proper position following to your lamination condition.
4. After pressing the RUN/STOP button choose and set proper speed by using the SPEED
button or .
5. Turn on the take up device and set the proper film tension by pressing the RUN/STOP button.
Lower tension would make better operation.
Set pressure lever at the Hard board/15mm mode.
10.
11. Turn off the power switch.
*** Reference ***
1. Set up the protection paper. Otherwise, glue form the film will be stuck on the face of roller
and it can be seriously damaged.
2. Turn the switch RUN/STOP and “Take up motor” at the same time.
- 11 -
METHOD FOR USING CUTTER
**Cross Cutter**
1. It is on the back side of the machine.
2. After lamination, move cutter to a point about 1/3 of
the width of lamination.
3. Grasp film with one hand and press the cutter, cutter
downward and slide it to the direction intending to
cut with another hand.
4.Press the cutter and slide it the other way.
- 12 -
q
IMPORTANT SAFETY CONCERNS
1.Please be cautious that neck tie, necklace, long hair, clothes are kept well away while
operation.
2.Prevent children from accessing the machine Extreme Heat Will Cause Injury
3.Place the machines on the plated place in order to prevent the machine from damage.
4.Make certain that the machine is connecterd to an ade
5.Do not use any other purposes other than Lamination.
uate power souce.
MAINTENANCE
1.Do not allow the machine to run with only one roll of film installed. The melted resin will
adhere to one roller and ruin future laminations.
2.The width of film should be bigger than the material, and Width of upper side and lower
side of film should be same in order not to allow melted resin to adhere to the rollers.
3.Be sure to adjust the film tension while in operation. If the tension is too tight, it could
cause the film to stretch.
4.After work, you should clean the resin from the rollers before beginning the next operation
5.Please check the lubricant after long operation or you do not use for a long time.
6.Check the chain linking each gear is not loosened.The limit tension allowed is 3mm.
- 13 -
It's not out of order
CauseSymptom
*Rollers do not operate1. Check the power cord.
after press RUN button
*Wrinkled lamination1. Adjust film tension.
result
1. Power cord may not be plugged
in.
2. Power switch is at OFF mode.
3. Emergency switch may be at
ON mode.
4. The safety cover is opened.
1. Film tension is not proper, too
tight.
CHECK POINT
2. Check if the switch is on.
3. Check if the emergency switch
is off.
4. Check the s/w of safety cover is right.
ASSEMBLY PARTS
PART NAME
Core(76mm)
MODELPART NAME
Bolt(M8X12)
EAEA
MODEL
FUSE(50T)
(AC250V 6.3A)
FUSE(65TS)
(AC250V 20A)
10
1
1
RSC-1650H
RSC-1650C
Washer(Φ8)
BOLT CORE
6
6
RSC-1650H
RSC-1650C
8
- 14 -
WARRANTY
1. For six month from the date of purchase, Royal Sovereign International Corporation or its authorized
service center will repair this product free of charge if it is defective in material or workmanship.
2. This Limited Warranty does not include cleaning, or damage caused by accident, neglect, misuse or
improper installation, operation or external scratch, any damage caused from service, maintenance,
modifications or tampering by anyone other than a Sovereign authorized service representative, or
damage caused by a natural calamity such as fire or earthquake and etc...
3. Customers will bear the expense of Transportation fee and delivery fee of the damaged machine.
- 15 -
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.