Royal Prestige FP2000 User Manual
MODEL FP2000
FILTERED SHOWER SYSTEM
USE & CARE MANUAL
Questions or Comments: 1-800-273-3373
8am-5pm Central Standard Time
IMPORTANT: Read and Save these Instructions
FRESCAPURE™
INTRODUCTION
Congratulations on the purchase of your new FrescaPure™
Filtered Shower System! You have taken an important step
towards improving the quality of your shower water.
This System significantly reduces free available chlorine from
you shower. Don’t be too surprised when you realize just how
much your shower experience is noticeably improved!
You may notice that you breath easier, consume less soap
and hair conditioner, and find that your hair and skin are just
naturally soft to the touch! What’s more, common skin conditions that are created from chlorine irritation such as rash,
flaking, itching and dryness virtually disappear!
FrescaPure™ Filtered Shower Systems are so advanced that
soap residue and build up on glass and tiled surfaces are
greatly reduced. You have made a wise investment. Now,
please take a few additional minutes to complete reading this manual, so that you may realize all the benefits
your new FrescaPure™ Filtered Shower System has to offer!
IMPORTANT USE GUIDELINES
1. For this System to continue to perform as tested and represented, use only Genuine Royal Prestige Replacement
Cartridges. Replacement Cartridges may be purchased
from your Independent Royal Prestige Representative, for
purchase information you may also call the Royal Prestige
Customer Service Center at 1-800-279-3373.
2. The actual capacity of your Cartridge may vary from the
rated capacity. This may be due to the volume of contaminants actually present in your water supply. Replace the
Cartridge upon the first occurance of the following:
• Everythreemonths
• Whentheowratediminishes
• Whenyounoticeanodorreoccurrence
• WhentheratedcapacityoftheCartridgehas
been reached
3. Read the manual completely before attempting to install
or use this product.
4. For use on cold potable water supplies only.
5. Installation of this product must comply with all state and
local laws and regulations. Refer to your local agencies for
details.
6. The contaminants or other substances removed or reduced
by this System are not necessarily in all user’s water.
OPERATING SPECIFICATIONS
Installation Shower
EPA Establishment Number 63018-NV-001
Rated Capacity 10,000 gallons (U.S.)
Replacement Cartridge RC-20-FP
Approximate Flow Rate @ 80 psi 2.5 gal/min
Housing Construction High Impact Plated ABS
Maximum Working Pressure 100 PSIG (689.5 kPa)
Maximum Operating Temperature 160º F /71º C
Minimum Operating Temperature 34º F/1º C
REPLACEMENT PARTS DIRECTORY
FRESCAPURE™ SHOWER FILTER
ITEM PART NO. DESCRIPTION
1 N/A Existing Shower Arm
2 4-301-0007 Gasket
3 3-201-0007 Nut
4 4-101-0017 Filter housing
5 4-500-0020 Pre-filter
6 0010-10-01 Cartridge
7 4-401-0030 O-Ring
8 4-101-0018 Filter Base
9 0010-10-05 Shower Wand
10 3-501-0020 Swivel
11 0010-06-04 Hose
SET UP AND INSTALLATION
1. Remove the existing shower head from your existing shower arm by turning counter-clockwise.
2. Insert Gasket into Collar located on Filter Housing. Thread Collar clockwise directly onto existing
shower arm until tight. Do Not Over-Tighten.
CAUTION: Threads from shower arm may cut Gasket if
improperly installed. This may result is leakage around
the Collar. If leak persists, use Teflon tape which is provided. Wrap Teflon tape around threads on existing
shower arm 1 1/2 times. Re-thread Collar clockwise directly onto existing shower arm until tight. Do not over-tighten.
1
2
3
9
4
2
10
5
6
7
8
2
11
FRESCAPURE™ 1
Loading...