Page 1
2.4 GHz WIRELESS
GUITAR SYSTEM
RYWRLSSGTRA
Page 2
Page 3
Charging the devices
Use the USB cable for charging. Attach to an adaptor or power supply (rated 5V/2A) to
charge. While charging, ensure that the device is shut down for most effective and fast
charge. Failure to do so may lead to shorter battery life.
When the device is not in use, power off to avoid continuous battery consumption.
Connections
When connecting and disconnecting to guitar or equipment (amps, pedals, etc), ensure the
additional equipment is turned off. Turn on the Wireless System first, then pedals, with the
amp on last. This will help to prevent damage both to this device and other relevant
equipment.
Interference
Operation is subject to the two following conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including the interference that may
cause undesired operation.
Warning
To reduce the risk of fire of electric shock, do not expose appliance to rain or moisture.
Page 4
OVERVIEW
(connects to instrument,
such as guitar or bass)
1. Input (mono)
2. 280° rotating head: adjustable to suit most instrument and amp configurations
3. Micro USB port for charging via USB cable
4. LED indicator light
• RED:
• GREEN:
5. Pairing button: Once powered on, long-press to begin pairing process
6. Power button: Press to turn device on/off
Transmitter
o While charging the device, solid red light
o During operation, red light appears when battery is low
o Solid green light: Device is connected
o Flashing slowly: Device is on, not connected (ready for pairing)
o Flashing rapidly: Pairing is in process
Receiver
(connects to amplifier,
pedal, mixer, etc.)
Page 5
• Plug the Transmitter into your instrument signal output port (guitar, bass, etc), and
plug the Receiver into your output device (amplifier, pedal, mixer, etc) input port.
For example:
Instrument > Transmitter >>> Receiver > Amp
Guitar > Transmitter >>> Receiver > Pedal > Cable > Amp
Bass guitar > Transmitter >>> Receiver > Mixing board
• Press the power buttons on each device to turn on the power of both the
Transmitter and Receiver. The LED indicator lights of both devices should be green
and flashing slowly. This means the devices are not paired, but are ready for
pairing,
• Press and hold the Pairing button on the Receiver. The LED indicator will begin
flashing rapidly.
• Then, press and hold the Pairing button on the Transmitter. Pairing will commence,
it may take a few moments. When pairing is successful, the LED indicator lights of
the both devices will turn to solid GREEN.
• Please charge your Transmitter or Receiver via the Micro USB port when the LED
indicator begins to display red. This represents low battery. If the device will not turn
on (no LED lights), charge until full battery before trying again.
• This wireless system can support:
o Six pairs of devices (1x Transmitter and 1x Receiver each) working under the
same circumstances without interference (as shown in Figure 1)
o One Transmitter sending signal to several Receivers simultaneously
(as shown in Figure 2).
Page 6
Receivers:
Transmitter
(Figure 1)
(Figure 2)
Page 7
Sample range
24bit / 48KHz uncompressed digital transmission
Latency
<12 ms
Range
≥100 feet outdoors, unobstructed
THD+ Noise
-98dB
Dynamic Range
>105dB(A) weighted
Operating Band
2.4GHz ISM Worldwide
Frequency response
20~20KHz, +1dB / -3dB
Adjustable angle
280°
SPECIFICATIONS
Device cannot be powered on
and doesn't work.
Device can be powered on,
but cannot operate, with no
sound at all.
Strange noise while in use.
Device cannot be charged
properly.
How to connect to multiple
Receivers from one
Transmitter
If the devices are unused for a long time, or powered off
during low battery but not recharged for a long time,
the battery enters protection mode to preserve the
battery. Charge the battery to full before use.
Check whether the LED indicator is green. If the LED is
flashing, then the Transmitter and Receiver are to
paired yet. If the LED is red, charge the devices.
Noise can occur if there is quite strong electromagnetic
interference, or if the transmission distance is too far.
Try to shorten the transmission distance, and check
other devices in operation which may be transmitting
electromagnetic interference.
The lithium battery enters into protection if it's in low
battery for a long time. Ensure it is charging for over 10
minutes before turning on.
While pairing, turn on all Receivers and enter into
pairing status. Then, put the Transmitter into pairing
status. When the pairing is complete, it will be
connected to all of the Receivers.
Page 8
Need more information?
We hope that this user guide has given you
the assistance needed for a simple set-up.
For the most up-to-date guide for your product,
as well as any additional assistance you may require,
head online to help.kogan.com
Loading...