When using an electrical appliance, basic
precautions should always be followed,
including the following:
READ ALL INSTRUCTIONS BEFORE
USING THE VACUUM CLEANER
WARNING – To reduce the risk of fire,
electric shock, or injury :
• Do not allow to be used as a toy. Close
attention is necessary when used by or near
children.
• Use only as described in this manual. Use only
manufacturer's recommend attachments.
• Do not use with damaged cord or plug. If
appliance is not working as it should, has been
dropped, damaged, left outdoors, or dropped
into water, return it to a service center.
• Do not pull or carry by cord, use cord as a
handle, close a door on cord, or pull cord around
sharp edges or corners. Do not run appliance
over cord. Keep cord away from heated surfaces.
• Do not unplug by pulling on cord. To unplug,
grasp the plug, not the cord.
• Do not put any object into openings. Do not
use with any opening blocked; keep free of dust,
lint, hair, and anything that may reduce air ow.
• Keep hair, loose clothing, ngers, and all parts
of body away from openings and moving parts.
• Use extra care when cleaning on stairs.
• Do not handle charger, including charger plug,
and charger terminals with wet hands;
• Do not charge the unit outdoors.
• Use only the charger supplied by the
manufacturer to recharge. Use only Battery
Charger Model (12 V : SSA-10W US 220020 /
18 V : MSP-C0200IC29.0-9W-US / 24 V : MSPC0200IC36.0-9W-US).
• Do not incinerate the appliance even if it is
severely damaged. The batteries can explode in
a re.
• Do not pick up anything that is burning or
smoking, such as cigarettes, matches, or hot
ashes.
• Do not use without dust bag and/or lters in
place.
• Always turn off this appliance before
connecting or disconnecting motorized nozzle.
• Do not use to pick up ammable or
combustible liquids, such as gasoline, or use in
areas where they may be present.
• Your vacuum cleaner is an electrical device: it
must be used under normal conditions of use.
• Use and store the appliance out of reach of
children.
• Never leave the appliance operating without
supervision.
• Do not hold the vacuum head or the end of the
tube close to your eyes and ears.
• Do not use your vacuum cleaner on wet
surfaces, water or liquids of any kind, hot
substances, extremely ne substances (plaster,
cement, ash ...), large sharp objects (broken
glass), products that are harmful (solvents,
paint strippers ...), , corrosive (acids, cleaning
uids...), , ammable and explosive (petroleum
or alcohol-based).
• Never immerse the appliance or charger in
water or any other liquid, do not splash water on
the appliance or charger.
• Do not store outside and keep away from
damp areas.
• Do not use outdoors or on wet surfaces
• Never place the device close to a heat source
(oven, heating appliances or hot radiators).
• Do not expose the batteries to a room
temperature over 104°F.
• Do not disassemble the vacuum cleaner while
it is running.
• Never operate the vacuum cleaner without the
dust box and without the foam motor lter.
• Do not use the appliance:
- if it has fallen and has visible damage or
appears to be working abnormally.
- if the charger or the charger cord are damaged.
In this case, do not open it, but send it to the
nearest Rowenta Authorised Service Centre, as
special tools are needed to carry out any repairs
safely.
• Repairs are to be performed only by specialists
with original spare parts.
• Repairing an appliance oneself may constitute
a danger to the user.
• Use only guaranteed Rowenta accessories
(lters, batteries ...).
• Check that the power voltage indicated on the
nameplate of your vacuum cleaner’s charger
corresponds to that of your mains installation.
Repairs are to be performed only by specialists
with original spare parts. Repairing an appliance
oneself may constitute a danger to the user and
voids the guarantee.
SAVE THESE INSTRUCTIONS
4
This product has been designed for household
use only. Any commercial use, inappropriate
use or failure to comply with the instructions,
the manufacturer accepts no responsibility
and the guarantee will not apply.
This appliance is not designed to be used by
people (including children) with a physical,
sensory or mental impairment, or people
without knowledge or experience, unless they
are supervised or given prior instructions
EN
concerning the use of the appliance by
someone responsible for their safety.
Children must be supervised to ensure that
they do not play with the appliance.
For your safety, this appliance complies with
all enforceable standards and regulations
(Low Voltage Directives, Electromagnetic
Compatibility, Environment, etc.).
5
DESCRIPTION
1. Ergonomic handle
2. On off button
2.a “Off” position
2.b “Floor” position
2.c “Carpet/Booster” position
3. Booster light (LED)
4. Charging indicator light
5. Handle
6. Main body
7. Locking screw
8. Air ow grid
9. Dust compartment
9.a Dust container
9.b Dust separator
9.c Filter foam
9.d Cover
10. Hose connector
11. Delta suction head with integrated
elecrobrush
11.a Electrobrush
11.b Flexible neck
11.c Small wheels
12. Wheels
13. Charger
- 12 V : SSA-10W US 220020*
- 18 V : MSP-C0200IC29.0-9W-US*
- 24 V : MSP-C0200IC36.0-9W-US*
14. Batteries
- 12 V : ref. RS-RH5157*
- 18 V : ref. RS-RH4899*
- 24 V : ref. RS-RH4900*
15. Jack plug connection
BEFORE USING FOR THE FIRST TIME
1 • Mounting the appliance
Unpack your device and get rid of all the
labels. Keep your warranty card and read the
instructions for use carefully before using
your appliance for the rst time.
• Remove the screw from the handle and
leave the nut in its housing.
• Attach the handle by carefully inserting it
into the upper part of the main body (g.1)
• Insert the locking screw (7) into the handle
and tighten it with a screwdriver (g.2).
• Attach the Delta vacuum head (11) by
clipping it on to the lower part of the main
body (g. 3).
Note: to remove the Delta vacuum head,
press the eject button on the back (g. 4) and
remove the vacuum head from the main body.
2 • Charging the battery
IMPORTANT Use only the original charger
supplied with the appliance. Never charge
below 32°F and above 104°F.
Before using your vacuum cleaner for the
first time, the battery must be charged for 16
hours.
When you are charging, the switch must be on
the "Off" position.
• Place the vacuum cleaner near a power
outlet.
• Plug the charger into the mains and connect
it behind the handle (g.5).
• The charging light (4) on the front comes on.
Leave the vacuum cleaner to charge. The light
goes out at the end of the recharging cycle
(about 16 hours).
The appliance can remain permanently on
charge without any risk. The base might heat
up slightly, which is perfectly normal.
The vacuum cleaner should always be put
back on charge after use to ensure that it is
always available with a fully charged battery.
However, it is best to unplug it in the event of
prolonged absence (holidays, etc), in which
case, there may be a decrease in run-time
because of self-discharging.
EN
* Depending on model
6
3 •
Turning the vacuum cleaner on
Remove the charger cable from the vacuum
cleaner.
Hold the vacuum cleaner by the handle and
slide the power switch down, to one of the
two following positions (g.6):
• “Floor”: for smooth oors (2.b)
In the «Floor» position, the electrobrush (11.a)
built into the Delta vacuum head, operates at
normal speed.
Note: regularly check that the wheels at the
back of the suction attachment are clean.
• “Carpet / Booster” : for a better dust pick up
efciency on all kinds of oors (2.c)
In the «Carpet» position, the Booster light (3)
below the power switch comes on to indicate
that the electrobrush (11.a) is operating at high
speed.
Run-time of your vacuum cleaner * depending
on the position of use:
Position 1
« Floor »
12 Voltsup to 25 MINup to 15 MIN
18 Voltsup to 40 MINup to 30 MIN
24 Voltsup to 50 MINup to 40 MIN
USE OF THE ELECTROBRUSH
The Electrobrush is a motorised rotating
brush that ensures very effective cleaning.
It vacuums and cleans deep down. It has
bristles all along, enabling it to remove
threads and animal hair embedded in rugs
and carpets.
Note: If the suction attachment adheres to the
surface too much, place the switch back to the
«Floor» position.
ATTENTION Do not vacuum large debris that
may block the brush and damage it.
Do not use the electro-brush on deep pile
carpets, animal fur and curtain fringes.
CLEANING THE ELECTROBRUSH
ATTENTION Always stop your vacuum cleaner
and unplug the charger before maintenance
or cleaning.
Position 2
« Carpet /
Booster »
EN
Delicately cut the threads, hairs, animal fur,
etc. following the notch designed for this
purpose on the electrobrush (g.7).
FOR YOUR SECURITY
• Do not touch the rotating parts without having stopped the vacuum cleaner.
• Make sure the charger is not plugged in
before touching any of the rotating parts.
• Do not use the vacuum cleaner on a wet
surface.
• Never immerse your appliance in water.
TROUBLESHOOTING
The electrobrush is working less efficiently or
is making an abnormal noise
• The rotating brush or the hose are clogged:
stop the vacuum cleaner and clean them.
• The brush is worn: please contact an
Authorised Service Centre to have the brush
changed.
• The belt is worn: please contact an
Authorised Service Centre to have the belt
changed.
The electrobrush stops in the middle of
vacuuming
• The heat safety device has come on: stop
the vacuum cleaner by moving the switch
to the OFF position (2.a) and make sure the
charger is unplugged. Make sure that nothing
is impeding the rotation of the brush, if so remove the obstacle and clean the electrobrush
(g.7), then turn the vacuum cleaner back on.
The electrobrush is difficult to move
• The suction power is too high: reduce the
suction power by moving the switch to the
«Floor» position (2b).
If the problem persists, (take your vacuum
cleaner to the nearest Rowenta Approved
Service Centre. See the list of Rowenta
Authorised Service Centres or) contact the
Rowenta Consumer Service.
4 • Storage
After use, switch off your vacuum cleaner by
moving the switch to the OFF position (2a).
Your vacuum cleaner may then be put away
standing vertically wherever you want, in its
parking position.
To place the vacuum cleaner in its parking position: stand it vertically so as to lock it (Fig. 8)
* Depending on model
7
CLEANING AND MAINTENANCE
EN
To use it again: hold the handle and tilt it
backwards to release it from the parking position (Fig. 9)
IMPORTANT Always stop your vacuum cleaner and unplug the charger before maintenance or cleaning.
1 • Cleaning the dust
compartment (9)
1.a Quick emptying
When the dust compartment is full, empty it
as follows: remove the dust compartment by
sliding down (g.10), place it over a dustbin
and press the «push» button to open the
emptying hatch downwards and empty the
contents of the dust compartment (g.11).
Close the hatch (g.12), and replace the dust
compartment (g.13).
1.b Deep cleaning
The dust compartment should be cleaned out
regularly.
• Remove the dust compartment (g.10), then
separate each component (9).
• Remove the lter foam that protects the
motor (9c).
• Run the dust compartment (9a) under warm
water (g.14), along with the dust separator
(9b) and the cover (9d) and then let them dry
or wipe with a dry cloth.
• Wash the lter foam that protects the motor
(see paragraph 2).
• Once dry, replace the dust compartment
components, along with the replacement
lter foam (9c) that comes with your vacuum
cleaner.
• Close the dust compartment and reposition
it on the device.
It is recommended that you clean the lter
foam more frequently if you see a drop in the
efciency of your vacuum cleaner.
• Remove the dust compartment cover (9d)
and then remove the lter foam protecting the
motor (9c) (g.15).
• Clean the lter foam that protects the motor
(9c) with warm soapy water. Rinse it and leave
it to dry for at least 12 hours before putting it
back in the vacuum cleaner (g. 16).
IMPORTANT For optimal protection of the motor, make sure the lter foam is dry before you
put it back in. It is therefore necessary to leave
it to dry for at least 12 hours. Your vacuum
cleaner comes with an additional foam lter
so you can use the device while the original
foam lter is drying.
WARNING Never wash the dust compartment
components or the engine lter foam in a
dishwasher.
3 • Caring for your vacuum
cleaner
Wipe the body of the vacuum cleaner with a
soft wet cloth, then dry using a dry cloth
(g. 17)
IMPORTANT Do not use detergents or any corrosive or abrasive products. The transparency
of the dust compartment and/or dust separator cover may change over time. This does not
affect performance.
2 • Cleaning the lter foam
that protects the motor (9c)
WARNING Never operate the vacuum cleaner
without the motor lter foam.
To preserve the efciency of your device,
do not vacuum extremely ne substances
(plaster, cement, ash ...) and clean the engine
protection lter at least once a month.
8
BATTERIES
1 • Replacing the batteries
This device contains Nickel Metal Hydride
(NiMh) batteries that for safety reasons are
only accessible by a professional service
engineer.
When the battery is no longer able to maintain the charge, the NiMh battery pack must
be removed.
To replace the batteries, please contact the
nearest Authorised Service Centre.
2 • Scrapping the appliance
Do not dispose of your appliance without
having rst removed the batteries.
To remove the batteries, please contact an Approved Service Centre or proceed as follows:
unplug the appliance from the mains, remove
the handle from the main body by removing
the central screw, then remove the 5 assembly screws at the back of the handle (g.18).
Lift the top cover of the handle carefully and
disconnect the battery pack by pulling the
plug (g.19).
EN
Do not throw the battery pack out with household refuse, but contact Rowenta Consumer
Services (drop it off at the nearest Rowenta
Authorised Service Centre) or drop it at a
disposal site specically designed for that
purpose.
Warning
Do not replace a block of rechargeable
batteries with non-rechargeable batteries. To
change the batteries, please contact an Approved Service Centre.
The batteries are designed for indoor use
only. Never immerse them in water. The batteries must be handled with care. Do not put
batteries in your mouth. Do not let batteries
touch other metal objects (rings, nails, screws,
etc). You must take care not to create short
circuits in the batteries by inserting metal
objects at their ends. If a short circuit occurs,
the battery temperature may rise dangerously
and can cause serious burns or even catch
re. If the batteries leak, do not rub your eyes
or any mucous membranes. Wash your hands
and rinse your eyes with clean water. If the
discomfort persists, consult your doctor.
ENVIRONMENT
• All inoperable appliances must be deposited in an Authorised Service Centre which
disposes of it in accordance with existing
regulations.
Environment protection first!
Your appliance contains valuable materials
which can be recovered or recycled.
Take it to a collection point or an approved service centre so that it can be recycled.
9
Loading...
+ 21 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.