USER MANUAL
MOVIE MV2CX
Full-range System for Cinema
OUTLINE S.R.L.
Via Leonardo da Vinci, 56
25020 Flero (Brescia) Italy
Tel.: +39 030.3581341
Fax +39 030.3580431
info@outline.it
www.outline.it
2
SAFETY REGULATIONS
Please read this manual carefully and in its entirety. It contains important information regarding
safety issues, including guidelines for general safe
use of rigging systems as well as advisories on government regulations and liability laws. The suspension of large, heavy objects in public places is subject
to numerous laws and regulations at the national/
federal, state/provincial, and local levels. The user
must assume the responsibility for making sure that
the use of any rigging system and its components in
any particular circumstance or venue conform to all
applicable laws and regulations in force at the time.
GENERAL SAFETY RULES
• Carefully read this manual in all its parts
• Respect the working load limits and maximum con-
gurations of the elements and of any third-party
component (such as suspension points, motors,
rigging accessories, etc...)
• Do not incorporate any accessory not provided
by Outline; all damaged or defective components
must be replaced only by equivalent parts ap-
proved by Outline
• Ensure personnel health and safety, ensure that
no one is standing under the system during the
installation, ensure that all personnel involved in
the installation are equipped with personal safety
devices
• Always double check that the elements are cor-
rectly connected before suspending the system.
The rigging elements are easy to use, however the
installation shall be carried out only by qualied personnel that are familiar with the rigging techniques,
safety recommendations and with the instructions
described in this manual.
All mechanical components are subject to wear and
tear over prolonged use as well as corrosive agents,
impacts or inappropriate use. For this reasons users have the responsibility to adopt and adhere to a
schedule of inspections and maintenance. Key components (screws, connecting pins, welded points,
rigging bars) must be inspected before every use.
Outline strongly recommends to carefully inspect
the system components at least once a year, reporting in a written document the date, the name of the
inspector, the points checked and any anomalies
discovered.
DISPOSAL OF WASTE MATERIALS
Your product is designed and manufactured
with high quality material and components,
which can be recycled and reused. When
this crossed-out wheeled bin symbol is attached to
a product, it means the product is covered by the
European Directive 2002/96/EC and subsequent
amendments. This means that the product must
NOT be disposed with other waste. It is the user’s
responsibility to dispose of their electrical and
electronic equipment by handing it over to an approved re-processor. For more information about
where you can send your equipment for recycling,
please contact your local distributor. The correct
disposal of your old product will help prevent potential negative consequences for the environment
and human health.
CONFORMITY AND WARRANTY
All the Outline electro-acoustic and electronic devices are in accordance with objects stated by CEE/EU directives.
The CE declaration of conformity and the warranty
are printed on a document that is shipped with the
product.
OUTLINE S.R.L.
Via Leonardo da Vinci, 56
25020 Flero (Brescia) Italy
Tel.: +39 030.3581341
Fax +39 030.3580431
info@outline.it
www.outline.it
3
AMPLIFIER CONNECTION
MOUNTING INSTRUCTIONS
Movie MV2CX mounts a 15” bass woofer, a 15”
mid-low woofer and a 3” diaphragm compression
driver. The two woofers are bass loaded and the
compression driver is horn loaded and is coaxial to
the mid-woofer. The internal cross-over allows this
loudspeaker to be fully driven by a single amplier
channel. The system features a two-and-a-half-way
cross-over, which means a high-pass section for the
compression driver, a low-pass section for the mid-
low woofer and another low-pass section (tuned at a
lower frequency) for the bass woofer.
This speaker nds its best application as the main
component of an L-C-R system in small/medium
cinemas.
The system requires adequate amplication and
external processing to protect the components from
high input signals and low frequencies and to achieve
the best performance.
This system can be stacked on the ground or on any stable support.
Outline carries out on-going research for product improvement. New materials, manufacturing methods
and design upgrades are introduced to existing products without prior notice as a routine result of this philosophy. For this reason, any current Outline product may differ in some aspect from its description, but will
always equal or exceed the original design specications unless otherwise stated.
© Outline 2017
Operating manual product code: Z OMMV2CX
Release: 170925
Printed in Italy
Loading...