Roundup HDC9300300, HDC9300306 Owner's Manual
HOT DOG CORRAL
Model HDC
Series 9300000
Owner’s Manual
P/N 1010609
Rev. E
MANUFACTURING
NUMBERS:
9300300
9300302
9300304
9300306
9300308
9300309
9300320
9300321
9300322
9300324
9300330
9300331
9300332
9300334
9300336
9300340
9300341
9300342
9300344
9300350
9300351
9300352
9300356
9300374
9300380
C
®
®
®
HOT DOG CORRAL
1
P/N 1010609 Rev. E
A.J. Antunes & Co.
General
The Roundup Hot Dog Corral is a unique and innovative way to grill hot dogs. The hot dogs are placed in a
“corral” that moves up-and-down over a heated flat grill
surface. The corral motion allows the hot dogs to turn.
As the hot dogs turn, they roll in their own juices, producing a self-basting hot dog that sears in all the natural flavor.
The versatile Hot Dog Corral will accommodate any
size hot dog along with Polish sausage, bratwurst and
breakfast sausage.
This manual provides the safety, installation and operating procedures for the Hot Dog Corral. We recommend that all information contained in this manual be
read prior to installing and operating the unit.
Your Hot Dog Corral is manufactured from the finest
materials available and is assembled to Roundup’s
strict quality standards. This unit has been tested at
the factory to ensure dependable trouble-free operation.
OWNER INFORMATION
Unpacking .................................................................6
Equipment Setup ......................................................6
Operation
...................................................................8
General ......................................................................8
Operating Instructions ...............................................8
Maintenance
.............................................................8
Cleaning ...................................................................8
Inspecting and Aligning Drive Parts ..........................9
Troubleshooting
......................................................10
Wiring Diagrams......................................................
11
Replacement Parts ............................................
12-19
Warranty....................................................
Back Cover
Owner Information
.....................................................1
General ......................................................................1
Warranty Information .................................................1
Service/Technical Assistance ....................................2
Important Safety Information
...................................2
Specifications
............................................................4
Electrical Ratings ......................................................4
Electrical Cord & Plug Configurations ......................4
Capacities .................................................................4
Dimensions ...............................................................5
Shipping Weight........................................................5
Installation
.................................................................6
TABLE OF CONTENTS
IMPORTANT! Keep these instructions for future reference.
If the unit changes ownership, be sure this manual accompanies the equipment.
Warranty Information
Please read the full text of the Limited Warranty in this
manual.
If the unit arrives damaged, contact the carrier immediately and file a damage claim with them. Save all
packing materials when filing a claim. Freight damage
claims are the responsibility of the purchaser and are
not covered under warranty.
The warranty does not extend to:
• Damages caused in shipment or damage as
result of improper use.
• Installation of electrical service.
• Normal maintenance as outlined in this manual.
• Malfunction resulting from improper maintenance.
• Damage caused by abuse or careless handling.
• Damage from moisture into electrical
components
• Damage from tampering with, removal of, or
changing any preset control or safety device.
WARNING
GENERAL WARNING. Indicates information important to the proper operation of
the equipment. Failure to observe may
result in damage to the equipment and/or
severe bodily injury or death.
Throughout this manual, you will find the following safety words and symbols that signify important safety issues
with regards to operating or maintaining the equipment.
WARNING
ELECTRICAL WARNING. Indicates information relating to possible shock hazard.
Failure to observe may result in damage
to the equipment and/or severe bodily
injury or death.
CAUTION
GENERAL CAUTION. Indicates information important to the proper operation of
the equipment. Failure to observe may
result in damage to the equipment.
WARNING
HOT SURFACE WARNING. Indicates
information important to the handling of
equipment and parts. Failure to observe
caution could result in personal injury.
IMPORTANT SAFETY INFORMATION
HOT DOG CORRAL
2
P/N 1010609 Rev. E
A.J. Antunes & Co.
Service/Technical Assistance
If you experience any problems with the installation or
operation of your unit, contact your local Roundup
Authorized Service Agency.
Fill in the information below and have it handy when
calling your authorized service agency for assistance.
The serial number is on the specification plate located
on the unit.
Purchased From:
Date of Purchase:
Model No.:
Serial No.:
Mfg. No.:
OWNER INFORMATION (continued)
Refer to the service agency directory included with
your unit.
Authorized Service Agency
Name:
Phone No.:
Address:
Use only genuine Roundup replacement parts in this
unit. Use of replacement parts other than those supplied by the manufacturer will void the warranty. Your
Authorized Service Agency has been factory trained
and has a complete supply of parts for this unit.
You may also contact the factory at 1-800-253-2991 if
you have trouble locating your local authorized service
agency.
HOT DOG CORRAL
3
P/N 1010609 Rev. E
A.J. Antunes & Co.
In addition to the warnings and cautions in this manual,
use the following guidelines for safe operation of the
unit.
• Read all instructions before using equipment.
• For your safety, the equipment is furnished with a
properly grounded cord connector. Do not
attempt to defeat the grounded connector.
• Install or locate the equipment only for its intended use as described in this manual. Do not use
corrosive chemicals in this equipment.
• Do not operate this equipment if it has a damaged cord or plug, if it is not working properly, or
if it has been damaged or dropped.
• This equipment should be serviced by qualified
personnel only. Contact the nearest Roundup
authorized service facility for adjustment or repair.
• Do not block or cover any openings on the unit.
• Do not immerse cord or plug in water.
• Keep cord away from heated surfaces.
• Do not allow cord to hang over edge of table or
counter.
The following warnings and cautions appear
throughout this manual and should be carefully
observed.
• Turn the unit off, disconnect the power source
and allow unit to cool down before performing
any service or maintenance on the unit.
• The unit should be grounded according to
local electrical codes to prevent the possibility of electrical shock. It requires a grounded
receptacle with separate electrical lines, protected by fuses or circuit breaker of the proper rating.
• All electrical connections must be in accordance with local electrical codes and any
other applicable codes.
• WARNING ELECTRICAL SHOCK HAZARD.
FAILURE TO FOLLOW THESE INSTRUCTIONS
COULD RESULT IN SERIOUS INJURY OR
DEATH.
- Electrical ground is required on this appliance.
- Do not modify the power supply cord plug.
If it does not fit the outlet, have a proper
outlet installed by a qualified electrician.
- Do not use an extension cord with this
appliance.
- Check with a qualified electrician if you are
in doubt as to whether the appliance is
properly grounded.
• This equipment is to be installed to comply
with the local plumbing codes and any other
applicable codes.
• Do not clean this appliance with a water jet.
• Do not use a sanitizing solution or abrasive
materials. The use of these may cause damage to the stainless steel finish.
• Chlorides or phosphates in cleansing agents
(e.g. bleach, sanitizers, degreasers or detergents) could cause permanent damage to
stainless steel equipment. The damage is usually in the form of discoloration, dulling of
metal surface finish, pits, voids, holes or
cracks. This damage is permanent and not
covered by warranty.
• The following tips are recommended for maintenance of your stainless steel equipment.
- Always use soft, damp cloth for cleaning,
rinse with clear water and wipe dry. When
required, always rub in direction of metal
polish lines.
- Routing cleaning should be done daily
using soap, ammonia detergent and
water.
- Stains and spots should be sponged
using a vinegar solution as required.
- Finger marks and smears should be
rubbed off using soap and water.
- Hard water spots should be sponged
using a vinegar solution.
HOT DOG CORRAL
4
P/N 1010609 Rev. E
A.J. Antunes & Co.
Capacities
(Refrigerated Product Only–Not Frozen
)
Model Voltage Watts Amps Hertz
HDC-20 120 1000 8.3 50/60
230 1000 4.3 50/60
HDC-21A 120 1000 8.3 50/60
230 1250 5.4 50/60
HDC-30A 120 1500 12.5 50/60
230 1500 6.5 50/60
HDC-35A 120 1500 12.5 50/60
230 1750 7.6 50/60
HDC-50A 120 1500 12.5 50/60
230 1750 7.6 50/60
SPECIFICATIONS
Model At One Time Per Hour
HDC-20 4-to-a-pound 7" Hot Dogs
20 200
HDC-21A 4-to-a-pound 7" Hot Dogs
21 210
HDC-30A 4-to-a-pound 7" Hot Dogs
30 300
HDC-35A 4-to-a-pound 7" Hot Dogs
35 350
HDC-50A 4-to-a-pound 7" Hot Dogs
50 500
Electrical Ratings
Electrical Cord & Plug Configurations
CAUTION
All electrical connections must be in accordance
with local electrical codes and any other applicable codes.
WARNING
ELECTRICAL SHOCK HAZARD. FAILURE TO
FOLLOW THE INSTRUCTIONS IN THIS MANUAL
COULD RESULT IN SERIOUS INJURY OR DEATH.
• Electrical ground is required on this appliance.
• Do not modify the power supply cord plug. If it
does not fit the outlet, have a proper outlet
installed by a qualified electrician.
• Do not use an extension cord with this appliance.
• Check with a qualified electrician if you are in
doubt as to whether the appliance is properly
grounded.
Description Configuration
NEMA-5-15P
15 Amp, 120 VAC
CEE 7/7 Schuko
16 Amp, 250 VAC
BS-1363
13 Amp, 250 VAC
Commercial Cord
HOT DOG CORRAL
5
P/N 1010609 Rev. E
A.J. Antunes & Co.
Dimensions
Model Width (A) Depth (B) Height (C) Shipping Weight
HDC-20 18-3/4" 21" 8-1/2" 45 lbs.
(476 mm) (533 mm) (216 mm) (20 kg)
HDC-21A 22-7/8" 15-1/4" 7-1/4" 38 lbs.
(581 mm) (387 mm) (184 mm) (17.2 kg)
HDC-30A 22-7/8" 20-5/8" 7-1/4" 48 lbs.
(581 mm) (524 mm) (184 mm) (21.2 kg)
HDC-35A 33-3/8" 15-1/4" 7-1/4" 54 lbs.
(848 mm) (387 mm) (184 mm) (24.5 kg)
HDC-50A 33-3/8" 20-5/8" 7-1/4" 70 lbs.
(848 mm) (524 mm) (184 mm) (31.75 kg)
A
B
C
HOT DOG CORRAL
6
P/N 1010609 Rev. E
A.J. Antunes & Co.
Figure 1. Hot Dog Corral
Driver Frame
Unpacking
1. Remove unit and all packing materials from shipping carton.
2. Open the large box. Remove all packing materials and protective coverings from the unit and
parts.
NOTE: If any parts are missing or damaged, contact
Antunes Technical Service IMMEDIATELY at 1-877392-7854 or 630-784-1000.
3. Wash driver frame in soap and water. Wipe all
surfaces of the unit with a hot damp cloth.
NOTE: Do not use a dripping wet cloth. Wring out
before use.
4. Install driver frame onto unit.
Equipment Setup
When placing the unit into service, pay attention to the
following guidelines.
• Make sure power to the unit is off and the unit is
at room temperature.
• Do not block or cover any openings on the unit.
• Do not immerse cord or plug in water.
• Keep cord away from heated surfaces.
• Do not allow cord to hang over edge of table or
counter.
• Place unit on a sturdy, level table or work surface.
Ensure that the line voltage corresponds to the stated
voltage on the unit specification label.
Turn off the rocker switch (power on/off). Connect the
unit to the power supply.
INSTALLATION
CAUTION
All electrical connections must be in accordance
with local electrical codes and any other applicable codes.
WARNING
ELECTRICAL SHOCK HAZARD. FAILURE TO
FOLLOW THE INSTRUCTIONS IN THIS MANUAL
COULD RESULT IN SERIOUS INJURY OR DEATH.
• Electrical ground is required on this appliance.
• Do not modify the power supply cord plug. If it
does not fit the outlet, have a proper outlet
installed by a qualified electrician.
• Do not use an extension cord with this appliance.
• The unit should be grounded according to local
electrical codes to prevent the possibility of
electrical shock. It requires a grounded receptacle with separate electrical lines, protected by
fuses or circuit breaker of the proper rating.
• Check with a qualified electrician if you are in
doubt as to whether the appliance is properly
grounded.
Loading...