ROULE ELECTRONICS RL R17, RL R10A, RL R40 Users Manual
PIR ALARM KIT
RL-9830G4
Version1.0
Package Contents
ON
OFF
PIR alarm
(Main unit)
*2
Before using the product, please remove the insulation sheets from all transmitters.
2 screws together with 2 plastic plugs (for installing the main unit brackets) and 4 3M stickers(for door/window
magnetic sensors)are included in each screw pack.
The main unit includes a receiver module and a transmitter module inside.
Remote key fob
(Transmitter)
*2
PIR alarm (Main unit)
Speaker
Indicator light
PIR sensing area
Door/window
magnetic sensor
(Transmitter)
*4
Code button
Vibration alarm
(Transmitter,
3M stickers
included)
*2
Alarm indicator: When the main unit sounds an alarm,
the light will flash quickly along with the alarm sound.
Low battery indicator: When the batteries installed
in the main unit reach a low level, i.e., less than 3.3V,
the light will flash slowly (time interval of 3 seconds).
Please replace batteries immediately when the low
battery indicator light flashes.
Bracket
*2
Screw pack
Paring the Transmitters to the PIR Alarm
30s
A
A
-
-
+
BATTERY
BATTERY
BATTERY
+
+
-
1. Insert batteries to
the PIR alarms A and B.
User manual
*2
*1
B
-
-
+
BATTERY
BATTERY
BATTERY
+
+
-
2. For the PIR alarm A,
press the Code button
for 3 seconds by inserting
the screwdriver. A single
"Beep" will be heard.
d
A
3. Release the screwdriver and within 30 seconds:
3a. Remote key fob: press any button
3b. Vibration alarm: slide the switch to "RF" and
then knock on the vibration alarm. It will send a
wireless signal to the main unit.
a
ON
OFF
A
c
B
3c. Door/window magnetic sensor:
Separate the magnetic contact from
the alarm, the red indicator light
will be on.
3d. PIR alarm B: press the Code
button by inserting the screwdriver.
Also pair the transmitters to the PIR alarm B by following the steps above. You can add up to
32 transmitters to each PIR alarm.
4. The PIR alarm A will
give one "Beep" tone
to indicate that the
signal is received.
5. Press the Code button
again for 3 seconds by
inserting the screwdriver.
Two "Beep" tones will
be heard.
A
b
A
6. Release the screwdriver,
pairing is now completed.
Remote key fob (Transmitter)
Arm button
Disarm button
ON
OFF
Front view
Side view
Vibration alarm (Transmitter)
Speaker
RF
Off
RF+Alarm
Battery
Compartment
1
Door/window magnetic sensor
(Transmitter)
Indicator
light
Once paired to the main unit and in
the ARM mode if the magnetic
AWAY mode
HOME mode
Magnetic contact
Once paired to the main unit and in the ARM mode if the vibration alarm is
triggered by a vibration, it will sound or send a wireless signal to the main unit.
The main unit will sound when it receives the wireless signal from the vibration
alarm. To disarm the alarm press the OFF button on the remote key fob.
Switch Operation:
OFF: Power off.
RF: When triggered, it itself will not sound but will send a wireless signal to
the main unit.
RF+ALARM: Three "Beep" tones will be heard when powered. When
triggered, it will send a wireless signal to the main unit and after 2 seconds it
itself will also sound for 8 seconds.
contact is separated from the
door/window sensor the alarm will
sound. To disarm the alarm press the
OFF button on the remote key fob.
Clearing Code
-
-
+
BATTERY
BATTERY
BATTERY
+
+
-
Installation
PIR alarm
①
Firstly, install the bracket and attach the main unit to the
angle of the PIR alarm bracket and adjust the angle
accordingly.
②
The PIR alarm A or B
Press and hold the Code button by
inserting the screwdriver (as above)
before installing the batteries. Insert
batteries you will hear two "Beep" tones
that will confirm that the clearing code
has been successful.
NOTE: The above will clear the
code for all paired transmitters.
2-6M
The detecting range and
angle of the PIR alarm
90°
2
CR2032
Door/window magnetic sensor
1. Open the battery compartment to
insert a battery.
2. Fix the unit on the door or window
by using a 3M sticker.
Arming/Disarming via Remote Key Fobs
Remote Key Fob: Press "ON" to ARM the unit, "OFF" to DISARM the unit.
Switch: " " into the AWAY mode while " " is the HOME mode.
1) AWAY Mode
Slide the switch to " " AWAY mode and press "ON", the main unit will give one "Beep" tone. After 30 seconds, the
unit will enter into the ARM mode. If the door/window installed with the magnetic sensor is opened or the window
installed with the vibration alarm is knocked or someone enters the property and the PIR alarm detects the intrusion, the
PIR alarm will sound. To disarm the alarm press "OFF" on the remote key fob. When the PIR alarm receives the DISARM
command,it will give two "Beep" tones and if it is in the ALARM status, the sound will be immediately turned off.
2) HOME Mode
For use in the HOME mode you must use the door/window magnetic sensors or the vibration alarm. Slide the switch to
" " HOME mode and press "ON", the main unit will give one "Beep" tone. After 30 seconds, the unit will enter into the
ARM mode. NOTE: In this mode the PIR sensor is disabled, therefore, your windows and doors are protected by
magnetic sensors or vibration alarms whilst you are in the property. If a door or window is opened or knocked, the alarm
will sound. To disarm the alarm press "OFF" on the remote key fob.
NOTE: The description above is only for the system with one PIR alarm. If you want 2 PIR alarms in the system and
want them to be interlinked, they both must be paired to each other and be paired to the transmitters respectively.
After, you must arm 2 PIR alarms with the remote key fob. Once armed, 2 PIR alarms will sound if any transmitter is
triggered. In the AWAY mode, no matter which PIR alarm detects human movements, 2 PIR alarms will sound.
Remote key fobs can only turn off the sound of the PIR alarm. The sound of the vibration alarm, however, will be
auto stopped after 8 seconds.
Vibration Alarm
1. Open the battery compartment to insert batteries.
2. Fix the unit on the window by using a 3M sticker.
LR44
LR44 LR44
Technical Specifications
Remote key fob
(Transmitter)
Working Voltage DC 3.0V(CR2032) DC 3.0V(CR2032) 4.5 V (3x battery LR44)
Standby Current <2uA
Working Current ≤
Working Frequency
Working Distance >30m(no barrier)
Alarm Volume
Time Interval of
Each Vibration
(30cm)
12mA
433.92MHz±250KHz 433.92MHz±250KHz 433.92MHz±250KHz
/ / >95dB
/ / ≈
Door/window
magnetic sensor
(Transmitter)
≤
10uA
≤
15mA
≥80m (no barrier) ≥80m (no barrier)
Vibration alarm
(Transmitter)
≤
6uA
RF: <15mA
RF+ALARM: <100mA
5s
Tips
Recommended installation height: 1.6±0.3m, adjust the installation angle to face downward.
Do not install the product in direct sunlight or close to a radiator or heat source.
The detection range of the PIR alarm may vary slightly due to different environments.
Do not attempt to repair this product, please return to your retailer
According to the co-channel interference principle, the receive distance may be affected if a strong interference signal
exists within the using area.
If a car is travelling nearby, the receive distance may be affected as well..
Remove batteries if the product is not in use for a long time and dispose the batteries according to the local laws and
regulations.
Troubleshooting
1. The main unit false alarms.
Check if any animals are in the vicinity of the PIR sensor, During warm weather moving shadows may also
activate the alarm. Make sure that the PIR sensor is not positioned near a radiator or heat source.
Check if any appliances within the property are emitting a strong electromagnetic field near the door/window
magnetic contact. Strong electromagnetic fields may cause the door/window magnetic contact to false alarm.
2. The main unit cannot receive the signal sent from the transmitter (remote key fob or door/window
magnetic contact).
Check if the pairing between the transmitter and the main unit has been successful.
If the pairing was successful, check the battery voltage for both the main unit and the transmitter. Low voltage
will cause the product to fail.
3. When the PIR alarm detects movement, however, no alarm sounds.
Check if the low battery indicator is flashing (please replace batteries immediately).
If the unit is armed and set in the HOME mode and the PIR sensor detects an intrusion the alarm will not
sound. The PIR is disabled in the HOME mode.
Check if the main unit is installed correctly.
PIR alarm (Main unit)
Working Voltage DC 4.5V(1.5V/AA/LR6*3)
Working Current ≤100mA
Standby Current ≤0.5mA
Low Voltage Indicator ≤3.3V
Alarm Volume ≥100dB(30cm)
Wireless Frequency 433.92MHz±250KHz
Infrared Detective Distance ≤6m
Infrared Alarm Angle ≥100°
Arm Mode Arming delays 30s each time
Alarm Mode Alarm once triggered
Alarm Time 30s each time
Wireless Distance ≥30m (no barrier)
3
FCC Statement
Warning: Changes or modifications to this unit not expressly approved by theparty responsible
for compliance could void the user's authority to operate theequipment.
NOTE: This equipment has been tested and found to comply with the limits fora Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits aredesigned to provide reasonable protection against harmful interference in
aresidential installation. This equipment generates, uses and can radiate radiofrequency energy and, if not installed
and used in accordance with theinstructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particularinstallation. If this equipment does
cause harmful interference to radio ortelevision reception, which can be determined by turning the equipment off
andon, the user is encouraged to try to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to whichthe receiver is connected.
Consult the dealer or an experienced radio/TV technician for help
The device must not be co-located or operating in conjunction with any other antenna or transmitter.
Thi s de vice co mp lie s wi th Pa rt 1 5 of th e FC C Rul es .Op er ation i s su bje ct t o the
fol lowi ng two co ndi tions :
(1) this d evice m ay n ot ca us e har mf ul in te rfe re nce, an d
(2) thi s devic e mu st ac ce pt an y in ter fe ren ce r ece iv ed, inc lu din g in ter fe ren ce t hat
may ca use un des ired opera tio n.
4
Loading...