Rosslare SAK-25 Instruction Manual

Compatibility: The SAK-25 Wire to RF Transmitter, with Magnetic Contact Sensor, is compatible with a variety of

Rosslare's receivers and panels, in 433.92 or 868.35 MHz.

Model : SAK-25

ADVANCED FEATURES

* Programmable Locally or by PC Software Utility (RS232)
* Ultra Low Power Microprocessor Design with Real-Time Software
* Tamper-Proof Internal Antenna
* Supervised (Every 20 minutes), with Low Battery

detection and reporting to Rosslare's RF Control Units

* Cover and Wall (Selectable) - Double Tamper Detection
* Pulse counting Wired Input for Rolling Shutter, Shock

Detection facility programmable to 3,6, or 9 pulses

* 3 Channels (2 Wired, 1 Local Mag Contact) programmable

as three independent zone ID's or as a single zone ID's.

* Programmable Enable Disable of Local Magnetic Contact Sensor.

Inside Model : SAK-25

GENERAL DESCRIPTION

The SAK-25 Universal WIRE to RF Transmitter is a unique RF transmitter, with
advanced features that operates at 433.92 or 868.35 MHz designed for wireless
security and control applications.

Totally Universal: Convert Wired Sensors to Wireless, and interface them to the
RF Panel or Multi-Channel Receiver. Compatible with wired PIR / Door / Window /
Smoke / Rolling Shutter / Vibration sensors / Glass Break Detectors and more.

Main features are: Two programmable wired inputs and One local Magnetic
Contact Sensor, which may share a Supervised RF Sensor ID Code, or have three
separate Supervised ID Codes (Supervisor will transmit every 20 minutes, or 1
hour, depending on model ordered). The SAK-25 operates on a 3.6V / 900mAh
lithium battery with low current draw, one battery lasts for min 2 Years (With 200
Transmissions per day). In case of low Batt, SAK-25 will transmit a Low Battery
Signal to the control Unit. For Backup Power, an auxiliary power input can be
connected at +12V DC and GND from the host panel of the wired sensor, or an
AC/DC Adaptor.

PROGRAMMING

Programming of the SAK-25 can be performed locally using the LED and the
buttons S1 and S2, as well as, from a connected PC. You may connect to the
SAK-25 from the PC using the MD-14 RS232 to RS485 converter and Rosslare's
SAK-25 Utility Software for the PC. (Available from Rosslare Website),

Local Programming the operation of the SAK-25 is available locally using the push
buttons S1 and S2 and the Tri Color LED.

1) Press both buttons at the same time and release when the LED is solid red
to enter the menu

2) Press S1 to scroll Input 1 programming modes-Release at desired Mode.

3) Press S2 to scroll Input 2 programming modes-Release at desired Mode.

4) Press both S1 and S2 together to exit the menu.

Input 1

(Wired Input) Programmable Locally and by PC Link Software, as any of the
options below.

Mode 1: PIR (Normally Open)
Mode 2: PIR (Normally Closed)
Mode 3: Door/Window (Normally Open)
Mode 4: Door/ Window (Normally Closed)
Mode 5: Smoke (Normally Open)
Mode 6: Smoke (Normally Closed)

Input 2

(Wired Input) Programmable Locally and by PC Link Software, as any of the
options below.

Mode 1: PIR (Normally Open)
Mode 2: PIR (Normally Closed)
Mode 3: Door/Window (Normally Open)
Mode 4: Rolling Shutter 3 Pulse Count
Mode 5: Rolling Shutter 6 Pulse Count
Mode 6: Rolling Shutter 9 Pulse Count

SOLID RED LED MENU for programming

the operation of Inputs 1 and 2

Solid Red LED

Flashing Red LED

Solid Orange LED

Flashing Orange LED

Solid Green LED

Flashing Green LED

Local Programming Menu - S1

Solid Red LED

Flashing Red LED

Solid Orange LED

Flashing Orange LED

Solid Green LED

Flashing Green LED

Local Programming Menu - S2

Solid Red LED MENU

Input 2

Terminal
Blocks

Battery
Power

3.0V 1300mAh
Lithium Cell

S2 - Button

S1 - Button

And Cover
Tamper Switch

Silver Plated

Antenna

Customized

Internal Antenna

PC-Link Connector

RS-232 I/O connects

to PC via supplied

data cable.

Mag
Contact
Sensor

Input 1

Terminal
Blocks

- 1 -

SA-25 Instruction Manual - Version 1.0 (Page 1/4)

Compatibility: The SAK-25 Wire to RF Transmitter, with Magnetic Contact Sensor, is compatible with a variety of
Rosslare's receivers and panels, in 433.92 or 868.35 MHz

- 2 -

Local Programming the operation of the SAK-25 is available locally using the push buttons S1
and S2 and the Tri Color LED.

1) Press both buttons at the same time and release when the LED is solid orange to enter the
menu

2) You will see the current mode of the ID Code settings upon release of both of the buttons.

Mode 1: All channels report independent ID
Mode 2: All channels report same ID

3) Press S2 to toggle the current setting.

Same ID Code for all 3 Inputs

If the mode was independent ID's (Flashing Red),
pressing S2 will toggle the mode to same ID Codes for three Channels.

Press both S1 and S2 together to exit the menu.

Different ID Codes for all 3 Inputs

If the mode was Same ID's (Solid Red),
pressing S2 will toggle the mode to independent ID Codes for three Channels.

Press both S1 and S2 together to exit the menu.

SOLID ORANGE MENU for Programming Channels Common ID and Independent ID Codes.

S2

S2

Solid Red LED

Flashing Red LED

Solid Red LED

Flashing Red LED

Solid Red LED

Flashing Red LED

Solid Orange LED MENU

S2S1

LOCAL PROGRAMMING (cont.)

Local Programming the operation of the SAK-25 is available locally using the push buttons S1
and S2 and the Tri Color LED.

1) Press both buttons at the same time and release when the LED is solid orange to enter the
menu.

2) You will see the current mode of the ID Code settings upon release of both of the buttons.

Mode 1: Built-in Magnetic Sensor will not automatically send restore, only when the magnet
will be effectively restored.

Important Note: This local menu will only allow programming if Input 1 is programmed as
Magnetic Door/ sensor & Normally Open

Mode 2: Built-in magnetic sensor will automatically send the restore signal after two seconds,
even if the magnet has not been effectively restored.

Important Note: This local menu will only allow programming if Input 2 is programmed as 3,6
or 9 pulses rolling shutter or vibration pulse counting.

3) Press S2 to toggle the current setting

Toggling Mode 1 to Mode 2

If the mode was Mode 1 (Flashing Red) pressing S2 will toggle the mode to Mode 2.

Toggling Mode 2 to Mode 1

If the mode was Mode 2 (Flashing Red) pressing S2 will toggle the mode to Mode 1.

FLASHING ORANGE MENU for Programming Channel 3 Local Magnetic Sensor Restore Event Operation

Flashing Orange LED MENU

S2S1

Solid Red LED

Flashing Red LED

S2

S2

Solid Red LED

Flashing Red LED

Solid Red LED

Flashing Red LED

SA-25 Instruction Manual - Version 1.0 (Page 2/4)