MD-W11
Wireless Access Control Door
Interface
Installation Manual
MD-W11BP MD-W11F MD-W11N
Copyright © 2014 by Rosslare. All rights reserved.
This manual and the information contained herein are proprietary to ROSSLARE
ENTERPRISES LIMITED and/or its related companies and/or subsidiaries’
(hereafter: "ROSSLARE"). Only ROSSLARE and its customers have the right to
use the information.
No part of this manual may be re-produced or transmitted in any form or by any
means, electronic or mechanical, for any purpose, without the express written
permission of ROSSLARE.
ROSSLARE owns patents and patent applications, trademarks, copyrights, or
other intellectual property rights covering the subject matter in this manual.
TEXTS, IMAGES, AND ILLUSTRATIONS INCLUDING THEIR ARRANGEMENT IN
THIS DOCUMENT ARE SUBJECT TO THE PROTECTION OF COPYRIGHT LAWS
AND OTHER LEGAL RIGHTS WORLDWIDE. THEIR USE, REPRODUCTION, AND
TRANSMITTAL TO THIRD PARTIES WITHOUT EXPRESS WRITTEN PERMISSION
MAY RESULT IN LEGAL PROCEEDINGS.
The furnishing of this manual to any party does not give that party or any third
party any license to these patents, trademarks, copyrights or other intellectual
property rights, except as expressly provided in any written agreement of
ROSSLARE.
ROSSLARE reserves the right to revise and change this document at any time,
without being obliged to announce such revisions or changes beforehand or
after the fact.
Table of Contents
MD-W11 Installation Manual iii
Table of Contents
1. Introduction ................................................................ 8
1.1 Overview ................................................................................ 8
1.2 Features.................................................................................. 9
2. Technical Specifications ............................................ 10
2.1 Supported Card Transmission Formats .................................... 11
2.2 Supported Keypad Transmission Formats ................................ 11
2.3 Available Models ................................................................... 12
3. Installation and Wiring ............................................. 13
3.1 The Installation Kit ................................................................ 13
3.2 General Installation Requirements .......................................... 14
3.3 Installing the MD-W11N Unit ................................................. 14
3.4 Wiring the MD-W11N Unit .................................................... 15
3.5 Installing the MD-W11F Unit .................................................. 18
3.6 Wiring the MD-W11F Unit ..................................................... 19
3.7 Installing the MD-W11BP Battery Pack.................................... 20
3.8 Wiring the MD-W11BP Battery Pack ....................................... 20
3.9 Indications on the Near and Far Units ..................................... 20
3.10 Installer Recommendations .................................................... 21
4. Enrollment ................................................................. 22
4.1 Enrolling the Units ................................................................. 22
4.2 DIP Switches ......................................................................... 22
4.2.1 Near and Far Unit Modes .............................................................. 23
5. Operational Information .......................................... 26
A. Declaration of Conformity........................................ 27
Table of Contents
iv MD-W11 Installation Manual
B. Limited Warranty ...................................................... 28
List of Figures
MD-W11 Installation Manual v
List of Figures
Figure 1: MD-W11 Interface .............................................................................. 8
Figure 2: MD-W11 Back Cover ........................................................................ 14
Figure 3: Near Unit Wiring Diagram ................................................................. 15
Figure 4: Sample Wiring Detail ........................................................................ 17
Figure 5: Far Unit Wiring Diagram ................................................................... 19
Figure 6: LED Display Panel .............................................................................. 20
List of Tables
vi MD-W11 Installation Manual
List of Tables
Table 1: DIP Switch Settings ............................................................................ 22
Table 2: Unit Channels Setting ........................................................................ 23
Notice and Disclaimer
MD-W11 Installation Manual vii
Notice and Disclaimer
This manual’s sole purpose is to assist installers and/or users in the safe and
efficient installation and usage of the system and/or product described herein.
B
EFORE ATTEMPTING TO INSTALL AND/OR USE THE SYSTEM, THE INSTALLER AND THE
USER MUST READ THIS MANUAL AND BECOME FAMILIAR WITH ALL SAFETY
REQUIREMENTS AND OPERATING PROCEDURES
.
The system must not be used for purposes other than those for which it
was designed.
The use of the software associated with the system and/or product, if
applicable, is subject to the terms of the license provided as part of the
purchase documents.
ROSSLARE exclusive warranty and liability is limited to the warranty and
liability statement provided in an appendix at the end of this document.
This manual describes the maximum configuration of the system with the
maximum number of functions, including future options. Therefore, not all
functions described in this manual may be available in the specific system
and/or product configuration you purchased.
Incorrect operation or installation, or failure of the user to effectively
maintain the system, relieves the manufacturer (and seller) from all or any
responsibility for consequent noncompliance, damage, or injury.
The text, images and graphics contained in the manual are for the purpose
of illustration and reference only.
All data contained herein is subject to change without prior notice.
In no event shall manufacturer be liable for any special, direct, indirect,
incidental, consequential, exemplary or punitive damages (including,
without limitation, any and all damages from business interruption, loss of
profits or revenue, cost of capital or loss of use of any property or capital or
injury).
All graphics in this manual are for reference only, some deviation between
the image(s) and the actual product may occur.
All wiring diagrams are intended for reference only, the photograph or
graphic of the PCB(s) are intended for clearer illustration and
understanding of the product and may differ from the actual PCB(s).
Introduction
8 MD-W11 Installation Manual
1. Introduction
1.1 Overview
The MD-W11 Wireless Access Control Door Interface is a quick and
inexpensive solution for connecting remote door devices, such as
readers, locks, and Request-for-Exit (REX) buttons to an access control
unit.
The MD-W11 consists of two units per door – one located near the
controller (the Near Unit) and the other near the door (the Far Unit)
(Figure 1).
Figure 1: MD-W11 Interface
Near Unit Far Unit Battery Pack
The Near Unit is connected to a Rosslare door controller (such as AC215, AC-225, or AC-525). The Far Unit is connected to proximity card
readers or keypads (such as AY-K12 and AY-Q64B).
When a card is read or a code is entered by keypad, the Far Unit
transmits the information to the Near Unit. The Near Unit, attached to
the controller, determines whether or not to open the door. The
controller then sends the message to the Near Unit, which transmits it
to the Far Unit, and if authorized, the door is opened.
Changes or modifications to this equipment not expressly
approved by the party responsible for compliance (Rosslare)
could void the user’s authority to operate the equipment.
Introduction
MD-W11 Installation Manual 9
1.2 Features
The MD-W11 Wireless Access Control Door Interface includes:
Bi-directional RF data communication
Supports PIN codes and card formats, such as Wiegand 26-Bit,
Wiegand 32-Bit, and Wiegand 6-Bit Rosslare formats (see
Section 2.1).
Lock and door relay commands
Tamper, door monitor, and REX messages between the controller
and the interface unit
Rolling code to increase security
Four different RF channels to prevent collisions
Built-in charger for up to 12 VDC, 7 Ah backup battery on the Far
Unit
Transfers proximity card information and LED control, reader
tamper, lock relay commands, REX, and door monitor events
between the coupled units.
Optional MD-W11BP battery pack housing with space for 12
VDC, 800 mAh, sealed lead-acid battery.
Suitable for indoor use.
Available in 869 MHz (H) and 433.92 MHz (G) bands
The Near Unit is powered from the controller's power supply. The
Far Unit is powered by a local wall transformer. A built-in charger
provides battery backup.
Loading...