KE-30
Installation Instructions Battery Operated Two-Way Wireless Keypad
1
0706-0960254+00
1. Introduction
The KE-30 is a wi re less keypad for use with Rosslare wireless
panels. The KE-30 feature s include:
• Fully featured keypad, including: LED indicators, function
buttons (arm-away, arm-home, disarm), numeric pad,
buzzer, and emergency triggering.
• RFID p roximity re ader for armi ng and disarming; The rang e
varies according to the type of card used, and is up to a
maximum of 2.5 cm.
• LED indications of the system status, including: Alarm In
Memory, Trouble and Bypass, and system status (armed
away / armed ho me / disarmed).
• Wall keypad tamper-protection mechanism.
• Low-power consumption; its internal bat t eries are
designed to last for years, under normal operation.
Figure 1: KE-30 Wireless Keypad
2. Technical Specifications
2.1 Electrical Characteristics
Power Supply Voltage: 4 batteries - CR123A 3V 1300mAh
Current Consumption: Standby - 17 uA ; Transmit 14 mA
Battery life –
2.2 Environmental Characteristics
1 year
Operating Environment: Indoor use
Operating Temperature: -10°C to 50°C (14°F to 122°F)
Operating Humidity:
2.3 Physical Characteristics
0 to 95% (Non-Condensing)
Dimensions HxWxD: 140x100x28 mm (5.51x3.94x1.10 inch)
Weight: 99g (0.218lb)
RFID Proximity Reader: Read-compatible with Wiegand 26-bit
EM4102 card (or compatible standard)
Read range: Maximum of 2.5 cm (using Rosslare's AT-R14)
Frequencies
3. Install the KE-30
: G-Band (433.92 MHz), H-Band (868.35 MHz)
3.1 Mounting the KE-30
Open the KE-30 and mount the back cover of the KE-30 flush
to the wall.
To mount the keypad on the wall:
1. Locate and release the s crews at the bottom of the
keypad, and open the cover.
2. Place the back pl ate at the desired location. (The keypad
should be installed at eye level.)
3. Use the dimensions given in the figure to the right, or use
the back cover as a tem plate.
4. Drill four h oles in the wa ll and insert the anchors provided.
5. Mount and fasten the back plate with the screws
provided, and assure that the back plate is level.
6. Secure the back plate with the screws referred to in
Step 1.
Figure 2: Mounting Dimensions
3.2 Replacing the Batteries
To replace the CR123A batteries:
1. Remove the used batteries and replace them .
2. Close the cover and the system is up and runni ng.
3.3 Enrolling the Keypad
Please refer to th e Keypad Enrolling section of the HomeLogiX
wireless pa nel manual or refer to any Rosslare wireless panel
manual that supports the re levant keypad.
3.4 Enrolling Proximity Cards
Please refer to th e Proximity Card Enrolling section of the
HomeLog iX wireless pan el manual or refer to any Rosslare
wireless panel manual that suppo r ts the relevant proximity
cards.
Figure 3: Battery Placement
2
0706-0960254+00
4. Tamper
The KE-30 is secured to the wall with a s c r ew (see Mounting
the KE-30). Tamper control is implemented vi a a knock-out
hole as soon as the KE-30 has been ins talled. Any attempt to
tamper with the system will set off an alarm.
Figure 4: Tamper Knock-Out
5. Utilizing the KE-30 Wireless keypad
The KE-30 functions as both an Arming/Disarming unit and as
a Status Viewing unit.
5.1 Arm/Disarm and Basic Operations
Below are i nstructions on how to arm the system usi ng t he
various options.
Basic Arming Using the keypad
• Press the ARM AWAY key, and enter the user cod e. The
system will beep, and the ARM AWAY LED indicator will
flash.
• Press th e ARM HOME key, and enter the user code. The
system will beep, and the ARM HOME LED indicator will
flash.
• Press th e DISARM key, and enter the user code. The
DISARM LED indicator will flash.
The QUICK AWAY and QUICK HOME functions:
• Press the A WAY button for 2 seconds. The system will
beep, and will be Arme d AWAY.
• Press the HOME button for 2 seconds. The system will
beep, and will be A r med HO ME.
Emergency Alarm Activation:
• Press on 1 and 3 simultaneously for 3 seconds to activate
the emergenc y alarm.
5.2 Status Viewing
Note
The KE-30 indicates a panel's status by flashing the relevant
LED indicator, and displays one of the following statuses:
: The ARM HOME LED indicator, the AR M AW AY LED
indicator, and the DISARM LED indicator flash, but they do
not remain on continuously.
• Armed Away
• Armed Home
• Disarmed
• In Memory and Trouble
• By-pass
When a new KE-30 unit is turned on, a flashing TROUBLE LED
indicator indicates that the unit must be enrolled. Once it
has been enrolled, the Disarm L ED indicator will flash.
If the system is experiencing trouble, the TROUBLE LED
indicator (!) will flash.
If there is an Alarm in Memory i n the System, the ALARM LED
indicator (M) will flash.
If the System is by-passed, the BYPASS LED indicator (Z) will
flash.
5.3 RFID Function
Note: The RFID function is deactivated by default, since if it is
activated, battery life will be significantly shortened.
Enabling the RFID Function:
Press both on the * key and the # key for 3 seconds until the
system beeps twice.
After the system beeps twice, press 1, and then press #.
When the RFID is activated, the system will beep once.
Cancelling the RFID function:
Press both on the * key and the # key for 3 seconds until the
system beeps twice.
After the system beeps twice, press 0, and then press #.
The RFID is now deactivated.
Enrolling proximity cards:
Please refer to the Proximity Card Enrolling section of the
HomeLog iX wireless pan el manual or refer to any Rosslare
wireless pa nel manual that supports the r elevant proximi ty
cards.
Using a Proximity Car d to ARM or DI SARM the System:
Note
Press on the Away, Home , or Di sarm button. then place the
card directly above the keypad. The system will activate the
desired function (Arm Away /Home or Disarm).
: First activate the RFID function.
Caution: Changes or modifications to this equipment
not expressly approved by the party responsible for
compliance (Rosslare Ltd.) could void the user’s
authority to oper ate the equipment.
Loading...