Rosslare EX-x22, EX-x04 Installation Manual

EX-x04 and EX-x22

Sensitive Piezoelectric Button Switch
Passive Infrared Motion Sensor Switch

Installation Manual

1

1. Introduction

The EX-H04 and EX-M04 are sensitive piezoelectric button switches.
The new access control switches are designed as flush mounting for US
and UK electric boxes with piezoelectric technology. The switches have
a red/green LED ring to display the switch status.

The switches are designed as Request-to-Exit (REX) buttons for access
control systems, direct activate electric strike, or magnet locks with up
to 30 VDC and 1A.

Figure 1: EX-H04 Figure 2: EX-M04

The EX-H22 and EX-M22 are passive infrared motion sensors (no touch
switch). The new access control switches are designed as flush
mounting for US and UK electric boxes with passive infrared
technology The switches have a red/green LED ring to display the
switch status.

The switches are designed as Request to Exit (REX) buttons for access
control systems, direct activate electric strike, or magnet locks with up
to 30 VDC and 1A.

Figure 3: EX-H22 Figure 4: EX-M22

2. Technical Specifications

2.1 Electrical Characteristics

Input Voltage

8–30 VDC

Switch Voltage

30 VDC [OC]

Maximum Switch Current

1 A

Sense Range (EX-x22)

5 to 20 cm

Sensitivity (EX-X04)

0.5 kg

LED Indicator

Red/green LED

2.2 Environmental Characteristics

Operating Environment

Outdoor use

Operating Temperature Range

-10˚C to 50˚C (14˚F to 122˚F)

Storage Temperature Range

-20˚C to 60˚C (-4˚F to 140˚F)

Operating Humidity

10% to 90%

2.3 5BPhysical Characteristics

Dimensions (W x H x D)

H: 114 x 70 x 10 mm (4.49 x 2.76 x 0.39 in.)
M: 92 x 92 x 10 mm (3.62 x 3.62 x 0.39 in.)

Weight

H: 50 g (1.76 oz)
M: 55 g (1.94 oz)

3. 2BInstallation

3.1 6BOperation Modes

The switches have two operation modes as determined by the brown
wire:

 Brown wire not connected – Momentary mode activates the

output [OC] for 1 second

 Brown wire connected to GND – Toggle mode activates the output

[OC] ON and OFF

The green wire sets the LED to the initial green color.

3.2 7BWiring Information

The switches are wired using a five-wire pigtail as described in Table 1:

Table 1: Wiring

Red

+Vin

Black

Ground (-Vin)

Brown

Mode setting

Green

LED setting

Yellow

Switch output (OC)

To wire the unit:

1. Connect the power supply to the black and red wires.

2. Connect the yellow wire to the REX input in the access control
panel or directly to the lock.

3.3 8BInstalling the Switch

When selecting the installation area, select a flat wall close to the door
or item that the switch will control. Ensure that there are no iron
beams, door frames, or other obstructions that may prevent insertion
of the inlay in the wall.

To install the switch:

1. Mark the dimensions of the inlay on the wall.

2. Mark two holes for the screws and a hole approximately in the
middle of the plate to insert the wires.

3. Drill the three holes.

4. Mount the unit and tighten the screws.

Figure 5: Wall Mount Figure 6: MP-06 Mount

2

Limited Warranty

The full ROSSLARE Limited Warranty Statement is available in the Quick
Links section on the ROSSLARE website at www.rosslaresecurity.com

.

Rosslare considers any use of this product as agreement to the
Warranty Terms even if you do not review them.

Contact Information

Asia Pacific, Middle East, Africa

Rosslare Enterprises Ltd.
Kowloon Bay, Hong Kong
Tel: [phone]
Fax: [phone]
[e-mail]

United States and Canada

Rosslare Security Products, Inc.

Southlake, TX, USA 76092
Toll Free: [phone]
Local: [phone]
Fax: [phone]

[e-mail]

Europe

Rosslare Israel Ltd.
Rosh HaAyin, Israel 48091
Tel: [phone]
Fax: [phone]
[e-mail]

Latin America

Rosslare Latin America
Buenos Aires, Argentina
Tel: [phone]
[e-mail]

China

Rosslare Electronics (Shenzhen) Ltd.
Shenzhen, China
Tel: [phone]
Fax: [phone]
[e-mail]

India

Rosslare Electronics India Pvt Ltd.
Tel/Fax: [phone]
Mobile: [phone]
[e-mail]

www.rosslaresecurity.com

0706-0960323+02