Rosslare DRU955BT User Manual

DR-U955BT

SMART

Multi-format Desktop Reader

User Manual

1. Introduction

The DR-U955BT is an advanced desktop reader for MIFARE Classic®
EV1, MIFARE
the credential, and transmits the relevant ID data to any connected
access control software, such as Rosslare’s AxTraxNG™.

It has a slim and attractive design and is built for convenience and
portability. With its USB computer interface, it is quick and easy to
install and runs without any additional power source.

Using the BLE-Admin or BLE-ID apps, the reader can function like
other Rosslare BLE readers and can transmit the BLE ID to the
reader.

The Hardware Configuration Tool (HCT) can be used to configure
the reader’s specifications, such as the Wiegand format used.

The reader reads the CSN ID of each credential (MIFARE, UHF, BLE)
and transmits it to the software with the bit length pre-configured by
the user.

®

DESFire® EV1, UHF, and BLE. It reads the ID data of

2. Technical Specifications

2.1 Electrical Characteristics

Operating Voltage Range 5 VDC (USB powered)

Standby Current 250 mA

Max. Operation Current 300 mA

Supported Transponders MIFARE, UHF, BLE

Read Card Distance UHF and MIFARE: Up to 5 cm (2 in.)

BLE: Up to 6 m (19.7 ft)

Operation Frequency

Output Formats Supports Wiegand 26-Bit to 64-Bit

• RFID: 13.56 MHz

• DR-U955BT US: 902–928 MHz

(America) RFID

• DR-U955BT EU: 865–868 MHz
(Europe) RFID

• Bluetooth: 2.402-2.480 GHz

Figure 1: DR-U955BT

2.2 Environmental Characteristics

Operating Environment Indoor use

Operating Temperature Range

Storage Temperature Range -20°C to 63°C (-4°F to 145°F)

Relative Humidity Range 0 to 95% (non-condensing)

-20°C to 63°C (-4°F to 145°F)

2.3 Physical Characteristics

Weight 130 g (4.6 oz)

Dimensions (L x W x H) 123 x 70 x 16.2 mm (4.9 x 2.8 x 0.6 in.)

3. Operation

The DR-U955BT appears as a COM port device when plugged in to a
PC and can be used for any application. When a card is presented to
the reader, the reader outputs the Wiegand ID data on the COM port
only once until a new card is presented.

You must use the AxTraxNG software to enroll cards. Please refer to
the relevant appendix in the AxTraxNG™ Software Installation and
User Manual.

For the enrollment reader to function in AxTraxNG, you must know
the COM port being used. The COM port can be found in Microsoft
Device Management’s driver details under ‘Ports (COM & LPT)’. The
port being used appears as “USB serial Port (COMx)”, where x is the
number of the port used.

1

Declaration of Conformity

 This device complies with Part 15 of the FCC Rules. Operation

is subject to the following two conditions:

 This device may not cause harmful interference.
 This device must accept any interference received, including

interference that may cause undesired operation.

 Changes or modifications not expressly approved by the party

responsible for compliance could void the user's authority to
operate the equipment.

This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:

Limited Warranty

 Reorient or relocate the receiving antenna.
 Increase the separation between the equipment and receiver.
 Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

 Consult the dealer or an experienced radio/TV technician for

help.

FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth
for an uncontrolled environment .
This transmitter must not be co-located or operating in conjunction with
any other antenna or transmitter.
This equipment should be installed and operate

d with minimum distance

20cm between the radiator &you body.

The full ROSSLARE Limited Warranty Statement is available in the
Quick Links section on the ROSSLARE website at

www.rosslaresecurity.com

.

Rosslare considers any use of this product as agreement to the
Warranty Terms even if you do not review them.

Contact Information

United States and Canada

Rosslare Security Products, Inc.
Southlake, TX, USA
Toll Free: [phone]
Local: [phone]
Fax: [phone]
[e-mail]

Europe

Rosslare Israel Ltd.
22 Ha'Melacha St., P.O.B. 11407
Rosh HaAyin, Israel
Tel: [phone]
Fax: [phone]
[e-mail]

Latin America

Rosslare Latin America
Buenos Aires, Argentina
[e-mail]

China

Rosslare Electronics (Shenzhen) Ltd.
Shenzhen, China
Tel: [phone]
Fax: [phone]
[e-mail]

Asia Pacific, Middle East, Africa

Rosslare Enterprises Ltd.
Kowloon Bay, Hong Kong
Tel: [phone]
Fax: [phone]
[e-mail]

India

Rosslare Electronics India Pvt Ltd.
Tel/Fax: [phone]
Mobile: [phone]
[e-mail]

CERT

ISO 9001
ISO 14001

2

0706-0960664+00