Rosslare AYX25B User Manual

AY-x5B Series

MIFARE Classic® EV1 CSN Readers

Installation Manual

1. Introduction

The AY-x5B is a series of RFID proximity card readers to be installed for
use with access control systems.

The AY-x5B series reads the card serial number (CSN) from MIFARE
Classic® EV1 credentials (4 UID and 7 UID) and transmits its data to
the access control system using Wiegand 26-Bit output.

Other Wiegand formats and the Clock & Data format are available as
factory configurable options.

2. Technical Specifications

2.1 Electrical Characteristics

Specifications AY-M5B AY-H5B AY-L5B AY-K5B

Power Supply Type

Operating Voltage
Range

Absolute Maximum
(non-operating)

Current @ 12V

Max. Read Range*

LED Control Input

Maximum Cable
Distance to
Controller

Frequency

Bit Rate

* Measured using a Rosslare MIFARE Classic EV1 card or equivalent. Range also

depends on installation environment, reader voltage, and proximity to metal.

6.5 cm

(2.6 in.)

Linear (recommended)

5–16 VDC

18 VDC

Standby: 45 mA

Maximum: 100 mA

7.0 cm

(2.8 in.)

Dry Contact, N.O.

18-AWG: 150 m (500 ft)

20-AWG: 90 m (300 ft)

13.56 MHz

106 KHz

6.0 cm

(2.4 in.)

Figure 1: AY-x5B Series

AY-M5B AY-H5B AY-L5B AY-K5B

2.2 Environmental Characteristics

Specifications AY-M5B AY-H5B AY-L5B AY-K5B

Operating Temp.
Range

Operating
Humidity Range

-31°C to 63°C (-25°F to 145°F)

0 to 95% (non-condensing)

2.3 Physical Characteristics

Model Dimensions

AY-M5B

AY-H5B

AY-L5B

AY-K5B

(H x W x D)

89 x 89 x 15 mm

(3.5 x 3.5 x 0.6 in.)

110 x 75 x 15 mm

(4.3 x 3.0 x 0.6 in.)

145 x 43 x 20 mm

(5.7 x 1.7 x 0.8 in.)

80 x 40 x 12.8 mm
(3.2 x 1.6 x 0.5 in.)

Weight

120.3 g
(4.2 oz.)

119.9 g
(4.2 oz)

115.2 g
(4.1 oz)

75.5 g

(2.7 oz)

3. Installation

Installation of an RFID reader adjacent to metallic surfaces
might alter the reader’s specifications. To diminish this
interference, use a plastic spacer when mounting the reader.

3.1 Installation Kit

The installation kit consists of the following items to be used during
the installation procedure:

 Two pan head mounting screws and screw anchors

3.2 Mounting

Before mounting, you should determine the best location for the
reader.

To mount the reader:

1. Drill two holes for mounting the reader on the wall.

2. Insert a screw anchor into each hole.

3. Drill a 10-mm (7/16”) hole for the cable. If mounting on metal,
place a grommet or electrical tape around the edge of the hole.

4. Remove the screw from the bottom of the unit.

5. Remove the reader's snap-off front cover.

6. Insert the unit’s cable wire into the cable hole and wire the unit as
described in Section 3.3. A linear type power supply is
recommended.

7. Align the two holes of the reader with those drilled in the wall and
firmly attach the reader to the wall with two screws (Figure 2).

Figure 2: Inserting Mounting Screws (similar for all models)

8. Relocate the front cover onto the reader.

9. Secure the front cover with the screw at the bottom of the unit.

1

3.3 Wiring

The AY-x2B is supplied with 5 color-coded wires 25 cm (10 in.) in
length.

To connect the reader to the controller:

1. Select the appropriate connections according to Table 1.

Table 1: Wiring

Wire Color Function

Red VIN 5–16 VDC

Black Ground

Green Data 0

White Data 1

Brown Green LED CTL

2. Connect the wires to the corresponding controller wires and cover
each joint with insulating tape.

3. Trim and cover all unused conductors.

When using a separate power supply for the reader, this supply
and that of the controller must have a common ground

Declaration of Conformity

FCC ID:GCD-AYX25B

 This device complies with Part 15 of the FCC Rules. Operation is

subject to the following two conditions:

 This device may not cause harmful interference.
 This device must accept any interference received, including

interference that may cause undesired operation.

 Changes or modifications not expressly approved by the party

responsible for compliance could void the user's authority to
operate the equipment.

This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation.

3.4 Operation Instructions

Once the reader is wired to a power supply and to the controller, you
should test the reader.

To test the reader:

1. Power up the reader.

Upon power up, the reader flashes and beeps once during Self­Test. The LED then turns red indicating the readers has entered
Standby mode.

2. Apply a MIFARE Classic EV1 credential to the reader.
The reader flashes and beeps once indicating the card has been

read successfully.

This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:

 Reorient or relocate the receiving antenna.
 Increase the separation between the equipment and receiver.

 Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

 Consult the dealer or an experienced radio/TV technician for help.

Limited Warranty

The full ROSSLARE Limited Warranty Statement is available in the Quick
Links section on the ROSSLARE website at www.rosslaresecurity.com

.

Rosslare considers any use of this product as agreement to the
Warranty Terms even if you do not review them.

Contact Information

United States and Canada

Rosslare Security Products, Inc.
Southlake, TX, USA
Toll Free: [phone]
Local: [phone]
Fax: [phone]
[e-mail]

Europe

Rosslare Israel Ltd.
22 Ha'Melacha St., P.O.B. 11407
Rosh HaAyin, Israel
Tel: [phone]
Fax: [phone]
[e-mail]

Latin America

Rosslare Latin America
Buenos Aires, Argentina
Tel: [phone]
[e-mail]

China

Rosslare Electronics (Shenzhen) Ltd.
Shenzhen, China
Tel: [phone]
Fax: [phone]
[e-mail]

Asia Pacific, Middle East, Africa

Rosslare Enterprises Ltd.
Kowloon Bay, Hong Kong
Tel: [phone]
Fax: [phone]
[e-mail]

India

Rosslare Electronics India Pvt Ltd.
Tel/Fax: [phone]
Mobile: [phone]
[e-mail]

CERT

ISO 9001
ISO 14001

2

0706-0960191+00