Rosslare AY-R12 Installation Manual

AY-R12

Outdoor RGB Illuminated Reader

Installation Manual

Copyright © 2014 by Rosslare. All rights reserved.

This manual and the information contained herein are proprietary to ROSSLARE
ENTERPRISES LIMITED and/or its related companies and/or subsidiaries’
(hereafter: "ROSSLARE"). Only ROSSLARE and its customers have the right to
use the information.

No part of this manual may be re-produced or transmitted in any form or by any
means, electronic or mechanical, for any purpose, without the express written
permission of ROSSLARE.

ROSSLARE owns patents and patent applications, trademarks, copyrights, or
other intellectual property rights covering the subject matter in this manual.

TEXTS, IMAGES, AND ILLUSTRATIONS INCLUDING THEIR ARRANGEMENT IN
THIS DOCUMENT ARE SUBJECT TO THE PROTECTION OF COPYRIGHT LAWS
AND OTHER LEGAL RIGHTS WORLDWIDE. THEIR USE, REPRODUCTION, AND
TRANSMITTAL TO THIRD PARTIES WITHOUT EXPRESS WRITTEN PERMISSION
MAY RESULT IN LEGAL PROCEEDINGS.

The furnishing of this manual to any party does not give that party or any third
party any license to these patents, trademarks, copyrights or other intellectual
property rights, except as expressly provided in any written agreement of
ROSSLARE.

ROSSLARE reserves the right to revise and change this document at any time,
without being obliged to announce such revisions or changes beforehand or
after the fact.

Table of Contents

AY-R12 Installation Manual iii

Table of Contents

1. Introduction ................................................................ 7

1.1 Features.................................................................................. 7

2. Technical Specifications .............................................. 8

3. Mounting Instructions ................................................ 9

4. Wiring Instructions ................................................... 10

5. Operating Instructions .............................................. 12

6. Testing the Reader .................................................... 13

A. Limited Warranty ...................................................... 14

List of Figures

iv AY-R12 Installation Manual

List of Figures

Figure 1: Mounting Template ............................................................................ 9

List of Tables

AY-R12 Installation Manual v

List of Tables

Table 1: Wiring Colors ..................................................................................... 10

Table 2: Operations Table ................................................................................ 12

Notice and Disclaimer

vi AY-R12 Installation Manual

Notice and Disclaimer

This manual’s sole purpose is to assist installers and/or users in the safe and
efficient installation and usage of the system and/or product described herein.

B

EFORE ATTEMPTING TO INSTALL AND/OR USE THE SYSTEM, THE INSTALLER AND THE

USER MUST READ THIS MANUAL AND BECOME FAMILIAR WITH ALL SAFETY
REQUIREMENTS AND OPERATING PROCEDURES

.

 The system must not be used for purposes other than those for which it

was designed.

 The use of the software associated with the system and/or product, if

applicable, is subject to the terms of the license provided as part of the
purchase documents.

 ROSSLARE exclusive warranty and liability is limited to the warranty and

liability statement provided in an appendix at the end of this document.

 This manual describes the maximum configuration of the system with the

maximum number of functions, including future options. Therefore, not all
functions described in this manual may be available in the specific system
and/or product configuration you purchased.

 Incorrect operation or installation, or failure of the user to effectively

maintain the system, relieves the manufacturer (and seller) from all or any
responsibility for consequent noncompliance, damage, or injury.

 The text, images and graphics contained in the manual are for the purpose

of illustration and reference only.

 All data contained herein is subject to change without prior notice.

 In no event shall manufacturer be liable for any special, direct, indirect,

incidental, consequential, exemplary or punitive damages (including,
without limitation, any and all damages from business interruption, loss of
profits or revenue, cost of capital or loss of use of any property or capital or
injury).

 All graphics in this manual are for reference only, some deviation between

the image(s) and the actual product may occur.

 All wiring diagrams are intended for reference only, the photograph or

graphic of the PCB(s) are intended for clearer illustration and
understanding of the product and may differ from the actual PCB(s).

Introduction

AY-R12 Installation Manual 7

1. Introduction

The AY-R12 Proximity Reader is an RFID proximity card reader and is
installed when using access control systems.

This is a unique product that has a variety of options to control the
reader's illumination according to various settings.

An example of this are the settings that enable users to set the reader
to project green light when everything is normal and red in case of
emergency; this is done by adjusting the inputs accordingly.

This product is compatible with any controller that supports the
Wiegand 26-Bit protocol (AC-215/225/425/525 panels; AC-015, AC­020, and AC-115 controllers; and AxTraxNG software), as well with
any third-party controllers that support the same Wiegand input.

The panel links are used to set various conditions between events and
outputs to get the required illumination from the reader.

1.1 Features

 Stylish and practical application to add color to any environment

enabling a high quality high-tech atmosphere

 Seven different colors to create a unique ambience
 Sixteen pre-programmed color schemes that are enabled using

wired inputs

 Optical back and cover tamper sends a signal to the control panel

when removed from wall or housing opening

 Built-in 125 kHz Reader for RFID cards with a read range of up to

8 cm (3.15 in.)

 Complies with RoHS, WEEE, CE standards for international

distribution

Technical Specifications

8 AY-R12 Installation Manual

2. Technical Specifications

Electrical Characteristics

Power Supply Type

Linear type (recommended)

Operating Voltage Range

12–16 VDC

Maximum Input Current

Standby: 100 mA
Read: 150 mA

Tamper Output

Open collector, active low, max. sink
current 16 mA

Read Range* (max)

8 cm (3.2 in.)

Maximum Cable Distance to
Controller

150 m (500 ft)

RE Modulation

ASK @ 125 kHz

Regulatory Approvals

CE

Environmental Characteristics

Operating Temp. Range

-31°C to 63°C (-25°F to 145°F)

Operating Humidity Range

0 to 95% (non-condensing)

Physical Characteristics

Height x Width x Depth

120 x 89 x 21 mm
(4.7 x 3.5 x 0.8 in.)

Weight

202 g (7.1 oz)

* Measured using a Rosslare proximity card or equivalent. Range also depends

on electrical environment and proximity to metal.

Mounting Instructions

AY-R12 Installation Manual 9

3. Mounting Instructions

Installation of an RFID reader adjacent to metallic surfaces
might alter the reader’s specifications. To diminish this
interference, use a plastic spacer when mounting the reader.

When mounting the reader, you must remove the snap-off cover to
access the screw holes.

To mount the reader:

1. Determine an appropriate mounting position for the reader.

2. Screw off the back of the unit and place it at the desired
mounting position.

3. Using the template as a guide, drill two holes (hole size is
indicated on mounting template) for mounting the reader to the
surface (Figure 1).

Figure 1: Mounting Template

4. Drill a 10-mm (

7

/16”) hole for the cable.

5. Route the interface cable from the reader to the controller.

The proximity reader is also mountable using strong epoxy glue.
After application, firmly hold the reader in place until the glue
dries

Wiring Instructions

10 AY-R12 Installation Manual

4. Wiring Instructions

The AY-R12 is supplied with a 10-wire 45-cm (18”) pigtail, comprising
a 6-conductor cable.

To connect the reader to the controller:

1. Prepare the reader cable by cutting its jacket back 4.5 cm (1¼”)
and strip the wires 1.3 cm (½”).

2. Prepare the controller cable by cutting its jacket back 3.2 cm
(1¼”) and stripping the wires 1.3 cm (½”).

3. Splice the reader’s pigtail wires to the corresponding controller
wires and cover each connection.

Table 1: Wiring Colors

Color Wiring

Black Ground

Red Vin

Green Data 0

White Data 1

Brown G.LED

Purple Tamper

Yellow SET 0

Blue SET 1

Gray SET 2

Orange SET 3

If the tamper output is being utilized, connect the purple wire to
the correct input on the controller.

Wiring Instructions

AY-R12 Installation Manual 11

4. Trim and cover all unused conductors.

• The individual wires from the reader are color-coded according the
Wiegand standard.

• When using a separate power supply for the reader, this supply and
that of the controller, must have a common ground.

• The reader’s cable shield wire should preferably be attached to an

earth ground, or a signal ground connection at the panel, or power

supply end of he cable. This configuration is best fro shielding the
Reader cable from external interference

Operating Instructions

12 AY-R12 Installation Manual

5. Operating Instructions

Table 2 shows the settings for Set 0 through Set 3, which determine
the color of the unit’s lighting.

Table 2: Operations Table

Operation Set 0 Set 1 Set 2 Set 3

Green

0 0 0 0

Green with dimming

0 0 0 1

Red

0 0 1 0

Red with dimming

0 0 1 1

Blue

0 1 0 0

Blue with dimming

0 1 0 1

Purple

0 1 1 0

Purple with dimming

0 1 1 1

Yellow

1 0 0 0

Yellow with dimming

1 0 0 1

Light Blue

1 0 1 0

Light Blue with dimming

1 0 1 1

White

1 1 0 0

White with dimming

1 1 0 1

No Illumination

1 1 1 0

7 colors circularly with dimmer

1 1 1 1

1 – Not connected; 0 – Connected to the ground

Testing the Reader

AY-R12 Installation Manual 13

6. Testing the Reader

Once the reader has been wired to a power supply and the controller,
it should be tested.

To test the reader:

1. Power up the reader. The beeper activates 3 times after which the
LED lights up green (according to Set 0, Set 1, Set 2, and Set 3
setup). This indicates that the reader is working properly.

The default is that the reader switches colors circularly. The color
can be set according to the input wires.

2. Present the appropriate type of proximity card to the reader. The
LED turns green (if set to default) and a short beep is emitted,
indicating that the card was read properly by to proximity reader.

Limited Warranty

14 AY-R12 Installation Manual

A. Limited Warranty

The full ROSSLARE Limited Warranty Statement is available in the
Quick Links section on the ROSSLARE website at

www.rosslaresecurity.com

.

Rosslare considers any use of this product as agreement to the
Warranty Terms even if you do not review them.

AY-R12

Asia Pacific, Middle
East, Africa

Rosslare Enterprises Ltd.
Kowloon Bay, Hong Kong
Tel: [phone]
Fax: [phone]
[e-mail]

United States and
Canada

Rosslare Security Products, Inc.
Southlake, TX, USA
Toll Free: [phone]
Local: [phone]
Fax: [phone]
[e-mail]

Europe

Rosslare Israel Ltd.
Rosh HaAyin, Israel
Tel: [phone]
Fax: [phone]
[e-mail]

Latin America

Rosslare Latin America
Buenos Aires, Argentina
Tel: [phone]
[e-mail]

China

Rosslare Electronics (Shenzhen) Ltd.
Shenzhen, China
Tel: [phone]
Fax: [phone]
[e-mail]

India

Rosslare Electronics India Pvt Ltd.
Tel/Fax: [phone]
Mobile: [phone]
[e-mail]

0706-0960232+02