Rosslare AY-Q6255 Installation And User Manual

AY-x6255 Family

CSN SELECT Smart Card Readers (Rev. A)

Installation and User Manual

1

1. Introduction

The CSN SELECT AY-x6255 is a family of multi-credential technology
contactless smart card readers for use in access control system
solutions. CSN SELECT readers have the capability to read the Card
Serial Number (CSN) from many smart card RFID Standards
implementations. The following list shows the credential technologies
for which we have confirmed compatibility:

 ISO14443A – MIFARE® Ultralight® Nano / EV1/ C, MIFARE

Classic® / Classic EV1, MIFARE Plus® S / SE / X / EV1, MIFARE
DESFire® EV1 / EV2, NFC N–TAG / Card Emulation

 ISO14443B – China National ID
 ISO15693 – HID® iClass®, PicoPass, iCode, LEGIC
 ISO18092 – SONY® FeliCa® (Hong Kong Octopus)

This list is continuously updated. For the latest compatibility list,
contact your sales representative.

The standard readers output the Wiegand CSN data in 26-bit format.
Other Wiegand formats are available upon request.

1.1 Installation Kit

The installation kit consists of the following items to be used during
the installation procedure:

 One self-adhesive mounting label template
 Two pan head mounting screws and screw anchors

 One pin Torx key tool
 One pin Torx security screw

AY-K6255 AY-L6255 AY-H6255 AY-M6255

2. Technical Specifications

2.1 Electrical Characteristics

Power Supply Type

Regulated

Operating Voltage Range

8 to 16 VDC

Current @ 12 V

AY-K/L6255: Standby: 55 mA, max: 80 mA
AY-H/M6255: Standby: 75 mA, max: 110 mA

Read Range*

AY-K6255: 5 cm (2.0 in.)
AY-L6255: 7 cm (2.9 in.)
AY-H/M6255: 9 cm (3.5 in.)

Green LED Control**

Dry Contact, N.O.

Red LED Control**

Dry Contact, N.O.

Buzzer Control**

Dry Contact, N.O.

Tamper Output**

Open collector, active low, max. sink current
16 mA

Maximum Cable Distance
to Controller

Wiegand: 150 m (500 ft) with 18-AWG cable
OSDP (RS-485): 1,200 m (4,000 ft) with 2x2 18-

AWG twisted shielded cable

* Measured using a Rosslare MIFARE Classic EV1 (ISO Card). Read range with

other credential technologies may vary. Range also depends on electrical
environment and proximity to metal.

** Control Lines are factory programmable and can be custom configured upon

request.

2.2 Environmental Characteristics

Operating Temp. Range

-35°C to 66°C (-31°F to 150°F)

Operating Humidity Range

0 to 95% (non-condensing)

Outdoor Usage

Weather-resistant, UV-resistant, meets IP65,
epoxy-potted, suitable for indoor and outdoor
use

2.3 Physical Characteristics

Dimensions
(H x W x D)

AY-K6255: 80.5 x 40.5 x 14.7 mm (3.2 x 1.6 x 0.6 in.)

AY-L6255: 145.0 x 43.0 x 22.3 mm (5.7 x 1.7 x 0.9 in.)

AY-H6255: 110.7 x 75.0 x 17.0 mm (4.4 x 3.0 x 0.7 in.)

AY-M6255: 89.5 x 88.5 x 16.9 mm (3.5 x 3.5 x 0.7 in.)

Weight

AY-K6255: 73 g (2.6 oz)

AY-L6255: 130 g (4.6 oz)

AY-H6255: 177 g (6.2 oz)

AY-M6255: 167 g (5.9 oz)

3. Wiring Instructions

The units are supplied with a 10-conductor 18” (46-cm) pigtail.

To connect the reader to the controller:

1. Prepare the reader cable by cutting its jacket back about 3 cm
(1¼”) and strip the insulation from the wires about 1.3 cm (½").

2. Prepare the controller cable by cutting its jacket back about 3 cm
(1¼") and strip the insulation from the wires about 1.3 cm (½").

3. Splice the reader’s pigtail wires to the corresponding controller
wires (see Table 1) and cover each joint with insulating tape.

4. If the tamper output is being utilized, connect the purple wire to
the correct input on the controller.

5. Trim and cover all unused conductors.

• The individual wires from the reader are color coded according the
Wiegand standard.

• When using a separate power supply for the reader, this supply and
that of the controller must have a c ommon ground.

• The reader’s cable shield wire should be preferably attached to an
earth ground, or a signal ground connection at the panel, or power
supply end of the cable.

Table 1: Wiring

Wire Color Function

Red Power

Black Ground

Green Data 0 / Data

White Data 1 / Clock

Orange Green LED control

Brown Red LED control

Purple Tamper Output

Yellow Buzzer control

Blue RS-485 - A / OSDP*

Gray RS-485 - B / OSDP*

* RS-485 is used for firmware update. OSDP function available only for the AY-

H6255 and AY-M6255 models.

2

4. OSDP Operation

• The AY-K6255 and AY-L6255 models do not currently support
OSDP function.

• In OSDP mode, all control lines (Inputs/Outputs) are disabled.

• In OSDP mode, if a connection is not established or lost with the

controller, the LED flashes orange continuously.

CSN SELECT readers that support OSDP operation are compatible with
all reader-related OSDP commands. The reader address is set using DIP
switches on the back of the reader. Release the screw on the back of
the reader to remove the door to access the DIP switches.

Figure 1 shows the DIP switch settings, which are described below.

Figure 1: DIP Switch Settings

 DIP Switch 1

This switch is used to select the reader output (Wiegand or OSDP):

 Off = Wiegand

 On = OSDP

 DIP Switch 2

This switch is reserved for future use.

 DIP Switch 3

This switch is reserved for future use.

 DIP Switches 4 to 8

These switches set the address of the reader for OSDP protocol.

DIP Switch 4 is MSB and DIP Switch 8 is LSB. The address is the DIP
switch state +1.

Examples:

 All the DIP switches in Off position, address = 1
 All the DIP switches in On position, address = 32

Declaration of Conformity

AY-M/H6255: FCC ID = GCD-AYCX6X55

AY-K/L6255: FCC ID = GCD-AYX6255

 This device complies with Part 15 of the FCC Rules. Operation is

subject to the following two conditions:

 This device may not cause harmful interference.
 This device must accept any interference received, including

interference that may cause undesired operation.

 Changes or modifications not expressly approved by the party

responsible for compliance could void the user's authority to
operate the equipment.

This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:

 Reorient or relocate the receiving antenna.

 Increase the separation between the equipment and receiver.
 Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

 Consult the dealer or an experienced radio/TV technician for help.

Limited Warranty

The full ROSSLARE Limited Warranty Statement is available in the Quick Links section on the ROSSLARE website at www.rosslaresecurity.com.
Rosslare considers any use of this product as agreement to the Warranty Terms even if you do not review them.

Contact Information

United States and Canada

Rosslare Security Products, Inc.
Southlake, TX, USA
Toll Free: [phone]
Local: [phone]
Fax: [phone]
[e-mail]

Europe

Rosslare Israel Ltd.
Rosh HaAyin, Israel
Tel: [phone]
Fax: [phone]
[e-mail]

Latin America

Rosslare Latin America
Buenos Aires, Argentina
Tel: [phone]
[e-mail]

China

Rosslare Electronics (Shenzhen) Ltd.
Shenzhen, China
Tel: [phone]
Fax: [phone]
[e-mail]

Asia Pacific, Middle East, Africa

Rosslare Enterprises Ltd.
Kowloon Bay, Hong Kong
Tel: [phone]
Fax: [phone]
[e-mail]

India

Rosslare Electronics India Pvt Ltd.
Tel/Fax: [phone]
Mobile: [phone]
[e-mail]

www.rosslaresecurity.com

0706-0960618+02