Rosslare AY-x20 Series, AY-M20, AY-H20, AY-J20, AY-L20 Installation Manual

...
Page 1
AY-x20 Family
Multi-format Proximity Readers
Installation Manual
1
1. Introduction
The AY-x20 is a family of RFID proximity card readers to be installed for use with access control systems. The AY-x20 family reads the proximity card and transmits its data to the access control system, using common multi-format Wiegand outputs.
1.1 Key Features
Selectable Wiegand 26-Bit, Clock & Data, or Serial RS-232 Reads 26-Bit EM or Rosslare format cards
Waterproof Green LED control line Red LED control line
Buzzer control line Hold control line
Optical tamper sensor Tamper output line UV-protected polycarbonate housing
Figure 1: AY-x20 Family
2. Technical Specifications
2.1 Electrical Characteristics
Specifications AY-M20 AY-J20 AY-H20 AY-L20 AY-K20
Power Supply Type
Linear type (recommended)
Operating Voltage Range*
5–16 VDC
Absolute Maximum (non­operating)
18 VDC
Current @ 12V
Standby: 35 mA
Maximum: 55 mA
Read Range**
10 cm
(3.94 in.)
12 cm
(4.72 in.)
8 cm
(3.15 in.)
LED Control Input
Dry Contact, N.O.
Tamper Output
Open collector, active low, max. sink current 16 mA
Maximum Cable Distance to Controller
150 m (500 ft)
RF Modulation
ASK, 125 KHz
Bit Rate
106 KHz
* All input voltages should be limited to 1 A maximum. For VAC, the voltage range is peak-to-peak.
** Measured using a Rosslare proximity card or equivalent. Range also depends on electrical environment and proximity to metal.
2.2 7BEnvironmental Characteristics
Specifications AY-M20 AY-J20 AY-H20 AY-L20 AY-K20
Operating Temp. Range
-31°C to 63°C (-25°F to 145°F)
Operating Humidity Range
0 to 95% (non-condensing)
2.3 8BPhysical Characteristics
Model Dimensions
(H x W x D)
Weight
AY-M20
88.91 x 88.91 x 15 mm (3.50 x 3.50 x 0.59 in.)
109 g
(3.85 oz.)
AY-J20
119.95 x 41.95 x 14 mm (4.72 x 1.65 x 0.55 in.)
88.5 g
(3.12 oz.)
AY-H20
109.91 x 74.91 x 15 mm (4.33 x 2.95 x 0.59 in.)
100 g
(3.53 oz)
AY-L20
144.91 x 42.91 x 20 mm (5.71 x 1.69 x 0.79 in.)
116 g
(4.09 oz)
AY-K20
79.91 x 39.91 x 12.8 mm (3.15 x 1.57 x 0.50 in.)
70.5 g
(2.49 oz)
AY-M20 AY-H20 AY-L20 AY-J20 AY-K20
Page 2
2
3. Installation
3.1 Installation Kit
The installation kit consists of the following items to be used during the installation procedure:
One mounting template Two pan head screws and wall plugs
One L-shaped security screw tool One security screw
3.2 Mounting the AY-x20 Reader
Before mounting, you should determine the best location for the reader.
To mount the reader:
1. Peel off the back of the self-adhesive mounting label template and place it at the required mounting location.
2. Using the template as a guide, drill two holes (sizes indicated on the template) used for mounting the reader onto the surface,
3. Insert a suitable wall plug into each hole.
4. Drill a 10-mm (7/16”) hole for the cable. If mounting on metal, place a grommet or electrical tape around the edge of the hole.
5. Wire the reader to the controller as described in Section 4. A linear type power supply is recommended.
6. Remove the reader's snap-off front cover to reveal the two screw holes (see Figure 2 ).
Figure 2: Removing the Top Cover
7. Align the two holes of the reader with those drilled in the wall and firmly attach the reader to the wall with two screws, whose size is indicated on the template.
8. Relocate the front cover onto the reader.
The reader can also be mounted using strong epoxy glue. After application, the reader should be firmly held in place until the glue dries.
Card readers are to be used with control panels whose power supply is UL Lis ted Class 2 or equivalent.
4. Wiring
The AY-x20 is supplied with a 10-conductor 18” pigtail.
To connect the reader to the controller:
9. Prepare the reader cable by cutting its jacket back about 3 cm (1¼") and strip the insulation from the wires about 1.2 cm (½").
10. Prepare the controller cable by cutting its jacket back 3 cm (1¼") and strip the insulation from the wires about 1.2 cm (½").
11. Splice the reader’s pigtail wires to the corresponding controller wires (as indicated in Table 1) and cover each joint with insulating tape.
Table 1: Wiring
Wire Color Wiegand 26-Bit
Output Mode
Clock & Data Output Mode
Serial (RS-232) Output Mode
Red +DC +DC +DC
Black Ground Ground Ground
Green Data 0 Data RS-232
White Data 1 Clock -
Orange Green LED Green LED Green LED
Brown Red LED Red LED Red LED
Yellow Buzzer Buzzer Buzzer
Blue Hold Hold Hold
Purple Tamper Tamper Tamper
Grey Open Input Connected to GND Connect to +DC
12. If the tamper output is being utilized, connect the purple wire to the correct input on the controller.
13. Trim and cover all unused conductors.
The individual wires from the reader are color-coded according the Wiegand standard.
When using a separate power supply for the reader, this supply and that of the controller must have a common ground.
The reader’s cable shield wire should be preferably attached to an earth ground, or a signal ground connection at the panel, or power supply end of the cable. This configuration is best for shielding the reader cable from external interference
5. Operation Instructions
5.1 Testing
Once the reader is wired to a power supply and to the controller, you should test the reader.
To test the reader:
1. Power up the reader.
The LED and beeper activate one time. This indicates that the reader is working properly.
2. Present the appropriate type of proximity card to the reader.
The LED momentarily flashes green and a short beep is emitted indicating that the card was read properly by the reader.
After the card data is processed by the controller, the controller can then turn the LED green. Refer to the controller description of the LED operation if the reader LED is controlled by the controller.
Page 3
3
5.2 Output Selection
For Wiegand 26-bit operation, the grey wire should be held not
connected.
For Clock & Data operation, the grey wire should be connected to
the ground
For Serial RS-232 operation, the grey wire should be held to +DC
(VIN).
5.3 LED Control
If the LED control wires (orange and brown) are not used (open), the reader LED remains red continuously, and flashes green momentarily when successfully reading a card.
The bi-color LED color can be controlled using the orange and brown wires.
When the orange wire is grounded, the LED is green When the brown wire is grounded, the LED is red
When both the brown and orange wires are grounded, the LED is
amber.
5.4 Buzzer Control
If the buzzer control wire (yellow) is not used (open), the buzzer beeps only when a card is read successfully. The buzzer can also be controlled using the yellow wire. When the yellow wire is grounded, the buzzer sounds.
5.5 Hold Control
The reading of cards can be disabled using the hold wire (blue). If the blue wire is grounded, the reader ignores all cards placed in its field. If the blue wire is open, the reader reads cards normally.
5.6 Tamper Output
This reader has an optical tamper sensor.
When the sensor detects light, the tamper output is grounded.
When the sensor does not detect light, the tamper output is held
to the high open collector.
Page 4
4
Limited Warranty
The full ROSSLARE Limited Warranty Statement is available in the Quick Links section on the ROSSLARE website at www.rosslaresecurity.com
.
Rosslare considers any use of this product as agreement to the Warranty Terms even if you do not review them.
Contact Information
United States and Canada
Rosslare Security Products, Inc. Southlake, TX, USA Toll Free: +1-866-632-1101 Local: +1-817-305-0006 Fax: +1-817-305-0069 support.na@rosslaresecurity.com
Europe
Rosslare Israel Ltd. Rosh HaAyin, Israel Tel: +972-3-938-6838 Fax: +972-3-938-6830 support.eu@rosslaresecurity.com
Latin America
Rosslare Latin America Buenos Aires, Argentina Tel: +54-11-4001-3104 support.la@rosslaresecurity.com
China
Rosslare Electronics (Shenzhen) Ltd. Shenzhen, China Tel: +86-755-8610-6842 Fax: +86-755-8610-6101 support.cn@rosslaresecurity.com
Asia Pacific, Middle East, Africa
Rosslare Enterprises Ltd. Kowloon Bay, Hong Kong Tel: +852-2795-5630 Fax: +852-2795-1508 support.apac@rosslaresecurity.com
India
Rosslare Electronics India Pvt Ltd. Tel/Fax: +91-20-40147830 Mobile: +91-9975768824 sales.in@rosslaresecurity.com
www.rosslaresecurity.com
0706-0960030+03
Loading...