Rosslare AY-H6255BT Installation And User Manual

AY-H6255BT

CSN SMART™ Smart Card Readers (Rev. A)

Installation and User Manual

1

1. Introduction

The CSN SMART™ AY-H6255BT is an innovative reader that lets
cardholders use smartphone apps as credentials in access control
systems by BLE ID and NFC ID compatible apps. The unit features three
technologies: a built-in CSN smart card (13.56 MHz) reader, an NFC ID
reader, and a Bluetooth BLE ID reader mode that supports BLE ID
transmitted by both Android and iOS smartphone apps.

The following list shows the credential technologies for which we have
confirmed compatibility:

 ISO14443A – MIFARE® Ultralight® Nano / EV1/ C, MIFARE

Classic® / Classic EV1, MIFARE Plus® S / SE / X / EV1, MIFARE
DESFire® EV1 / EV2, N-TAG NFC / Card Emulation

 ISO15693 – HID® iClass®, PicoPass, iCode, LEGIC

 ISO18092 – SONY® FeliCa® (Hong Kong Octopus)
 Rosslare’s CS-ECA NFC app (HCE) for Android smartphones

Scan the QR code to download Rosslare’s NFC app.

 Android app and BLE ID for Android and iPhone

This list is continuously updated. For the latest compatibility list,
contact your sales representative

The standard reader outputs the Wiegand CSN data in Wiegand 26-Bit
format. Other Wiegand formats are selectable using the

CS-CCT

Configuration Card Tool for the DR-6255

application.

1.1 Installation Kit

The installation kit consists of the following items to be used during
the installation procedure:

 1 self-adhesive mounting label template
 2 mounting screws and 2 screw anchors

 1 Torx key tool
 1 Torx security screw

Figure 1: AY-H6255BT

2. Technical Specifications

2.1 Electrical Characteristics

Power Supply Type

Regulated

Operating Voltage Range

8 to 16 VDC

Current @ 12 V

Standby: 110 mA, max: 185 mA

Bluetooth BLE Read Range

From 1 m to 10 m (3.2 to 32.5 ft) (line of sight)

RFID and NFC Read
Range*

5 cm to 10 m (2.0 to 3.9 in.)

LED/Buzzer Controls

Dry Contact, N.O.

Tamper Output

Open collector, active low, max. sink current
16 mA

Maximum Cable Distance
to Controller

Wiegand: 150 m (500 ft) with 18-AWG cable
OSDP (RS-485): 1,200 m (4,000 ft) with 2x2

18-AWG twisted shielded cable

* Measured using a Rosslare MIFARE Classic EV1 (ISO card). Read range with

other credential technologies may vary. Range also depends on electrical
environment and proximity to metal.

2.2 Environmental Characteristics

Operating Temp. Range

-35°C to 66°C (-31°F to 150°F)

Operating Humidity Range

0 to 95% (non-condensing)

Outdoor Usage

Weather-resistant, UV-resistant, meets IP65,
epoxy-potted, suitable for indoor and outdoor
use

2.3 Physical Characteristics

Dimensions
(H x W x D)

110.7 x 75.0 x 17.0 mm (4.4 x 3.0 x 0.7 in.)

Weight

177 g (6.2 oz)

3. Wiring

The units are supplied with a 10-conductor 5-m (16-ft) pigtail with
exposed wires coated with solder.

To connect the reader to the controller:

1. Select the appropriate connections according to Table 1.

2. Prepare the controller cable by cutting its jacket back about 3 cm
(1¼") and strip the insulation from the wires about 1.3 cm (½").

3. Splice the reader’s pigtail wires to the corresponding controller
wires and cover each joint with insulating tape.

4. If the tamper output is being utilized, connect the purple wire to
the correct input on the controller.

5. Trim and insulate the ends of all unused conductors individually.
Do not short any unused wires together.

• The individual wires from the reader are color coded according the
Wiegand standard.

• When using a separate power supply for the reader, this supply and
that of the controller must have a common ground.

• The reader’s cable shield wire should be preferably attached to an
earth ground, or a signal ground connection at the panel, or power
supply end of the cable.

Table 1: Wiring

Wire Color Function

Red Power

Black Ground

Green Data 0 / Data

White Data 1 / Clock

Orange Green LED Control*

Brown Red LED Control*

Purple Tamper Output

Yellow Buzzer Control*

Blue RS-485 – A / OSDP**

Gray RS-485 – B / OSDP**

* These wires have programmable functions that may be adjusted by presenting

a configuration card within 10 seconds upon powering on the unit. See the

CS-CCT Configuration Card Tool for the DR-6255 Software Manual

for how

you can create a configuration card.

** RS-485 is used for firmware update.

2

4. Bluetooth BLE ID and NFC ID Operation

4.1 NFC ID

The NFC ID read function of the AY-H6255BT can read both active and
passive NFC credentials. Rosslare features smartphone applications that
generate Unique NFC ID for each smartphone.

NFC ID is a short-range contactless technology that works at a range of
3 to 10 cm 2.0 to 3.9 in from the readers depending on the
smartphone or passive tag.

The reader scans for NFC ID and transmits the ID number to the host
controller via OSDP or Wiegand protocols.

To find out more information on Rosslare’s NFC ID credential app for
Android, talk to your nearest authorized reseller.

4.2 BLE ID

The BLE ID can read credentials via Bluetooth using Rosslare’s mobile
Bluetooth app

The service accepts incoming connection requests and transfers the
credential by Wiegand or OSDP connection to the host. This feature
includes MAC address and reader name advertising.

BLE ID credentials have a line-of-sight range of up to 10 m (33 ft) from
the reader depending on the type and brand of smartphone or BLE
device.

For more information about BLE functionality, please see the manual of
the credential. For additional information about apps, please refer
your enquiries to an authorized Rosslare distributor.

5. Configuration Card Programming

The

CS-CCT Configuration Card Tool for the DR-6255

application is
used to create a configuration card, which in turn can be used to
configure the AY-H6255BT reader.

The application allows you to configure RFID output settings, keypad
settings (for AYC models), input behavior for the LED, buzzer, and hold
controls, and the behavior for the LED and buzzer when a credential is
presented or when in Standby mode.

For more information, please see the

CS-CCT Configuration Card Tool

for the DR-6255 Software Manual

.

6. OSDP Operation

• In OSDP mode, all control lines (Inputs/Outputs) are disabled.

• In OSDP mode, if a connection is not established or lost with the

controller, the right LED flashes yellow continuously.

CSN SMART readers that support OSDP operation are compatible with
all reader-related OSDP commands. The reader address is set using DIP
switches on the back of the reader. Release the screw on the back of
the reader to remove the door to access the DIP switches.

Figure 2 shows the DIP switch settings, which are described below.

Figure 2: DIP Switch Settings

 DIP Switch 1

This switch is used to select the reader output (Wiegand or OSDP):

 Off = Wiegand
 On = OSDP

 DIP Switch 2

This switch is reserved for future use.

 DIP Switch 3

This switch is reserved for future use.

 DIP Switches 4 to 8

These switches set the address of the reader for OSDP protocol.
DIP Switch 4 is MSB and DIP Switch 8 is LSB. The address is the DIP

switch state +1.

Examples:

 All the DIP switches in Off position, address = 1

 All the DIP switches in On position, address = 32

7. LEDs Operation

7.1 Standby Mode

Once the reader powers on (or resets), the reader enters Standby
Mode. The left LED is blue and the right LED is red.

7.2 Card Read

When the reader reads a contactless card or NFC ID read, the right LED
flashes green and the unit beeps once. The data is transferred to the
host via Wiegand.

7.3 NFC ID Read

When the reader reads an NFC ID, the right LED flashes green and the
unit beeps twice. The ID is transferred to the host via Wiegand.

red blue

green

blue

green

blue

3

Declaration of Conformity

FCC ID: GCD-AYH6X55BT
This device complies with Part 15 of the FCC Rules. Operation is

subject to the following two conditions:

 This device may not cause harmful interference.
 This device must accept any interference received, including

interference that may cause undesired operation.

WARNING: Changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority to
operate the equipment.

NOTE: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment

generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:

 Reorient or relocate the receiving antenna.
 Increase the separation between the equipment and receiver.

 Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

 Consult the dealer or an experienced radio/TV technician for help.

Radio Equipment Directive (RED)

Rosslare hereby declares that the AY-H6255BT is in compliance with essential requirements and other relevant provisions of Directive 2014/53/EU.

Limited Warranty

The full ROSSLARE Limited Warranty Statement is available in the Quick Links section on the ROSSLARE website at www.rosslaresecurity.com.
Rosslare considers any use of this product as agreement to the Warranty Terms even if you do not review them.

International Standards Approvals

Description Latest Standard Latest EU Directive

CE-EMC

EN 61000-6-3:2007+A1:2011+AC:2012
EN 50130-4:2011+A1:2014
EN 61000-3-2:2014
EN 61000-3-3:2013
AOC

EMCD 2014/30/EU

CE-LVD

EN60950-1 : 2006+A11 : 2009+A1 : 2010+A12 : 2011+A2 : 2013

RED 2014/53/EU

CE-RED

N 300 330 V2.1.1
EN 301 489-1 V2.2.0
EN 301 489-3 V2.1.1
EN 301 489-17 V3.1.1/EN 300 328 V 2.1.1
EN62479: 2010
NB

RED 2014/53/EU

FCC

FCC Part 15B
FCC Part 15.225 and 15.247
FCC ID

Contact Information

United States and Canada

Rosslare Security Products, Inc.
Southlake, TX, USA
Toll Free: [phone]
Local: [phone]
Fax: [phone]
[e-mail]

Europe

Rosslare Israel Ltd.
22 Ha'Melacha St., P.O.B. 11407
Rosh HaAyin, Israel
Tel: [phone]
Fax: [phone]
[e-mail]

Latin America

Rosslare Latin America
Buenos Aires, Argentina
Tel: [phone]
[e-mail]

China

Rosslare Electronics (Shenzhen) Ltd.
Shenzhen, China
Tel: [phone]
Fax: [phone]
[e-mail]

Asia Pacific, Middle East, Africa

Rosslare Enterprises Ltd.
Kowloon Bay, Hong Kong
Tel: [phone]
Fax: [phone]
[e-mail]

India

Rosslare Electronics India Pvt Ltd.
Tel/Fax: [phone]
Mobile: [phone]
[e-mail]

CERT

ISO 9001
ISO 14001

BLE 4.1