Rosslare AuraSys L-2, AuraSys L-2K Hardware Installation Manual

AuraSys™ L-2

2-/4-Zone Alarm Access Panel

Hardware Installation Manual

Models:

L-2
L-2K

Copyright © 2012 by Rosslare. All rights reserved.

This manual and the information contained herein are proprietary to ROSSLARE
ENTERPRISES LIMITED and/or its related companies and/or subsidiaries’ (hereafter:
"ROSSLARE"). Only ROSSLARE and its customers have the right to use the information.

No part of this manual may be re-produced or transmitted in any form or by any means,
electronic or mechanical, for any purpose, without the express written permission of
ROSSLARE.

ROSSLARE owns patents and patent applications, trademarks, copyrights, or other
intellectual property rights covering the subject matter in this manual.

TEXTS, IMAGES, AND ILLUSTRATIONS INCLUDING THEIR ARRANGEMENT IN THIS
DOCUMENT ARE SUBJECT TO THE PROTECTION OF COPYRIGHT LAWS AND OTHER
LEGAL RIGHTS WORLDWIDE. THEIR USE, REPRODUCTION, AND TRANSMITTAL TO THIRD
PARTIES WITHOUT EXPRESS WRITTEN PERMISSION MAY RESULT IN LEGAL
PROCEEDINGS.

The furnishing of this manual to any party does not give that party or any third party any
license to these patents, trademarks, copyrights or other intellectual property rights,
except as expressly provided in any written agreement of ROSSLARE.

ROSSLARE reserves the right to revise and change this document at any time, without
being obliged to announce such revisions or changes beforehand or after the fact.

Table of Contents

AuraSys™ L-2 and L-2K Installation Manual iii

Table of Contents

1. Introduction ....................................................................... 8

2. Technical Specifications and Features .......................... 10

3. Installation and Wiring .................................................. 12

3.1 Installation Quick Guide .................................................................... 12

3.2 Installation Prerequisites .................................................................... 12

3.2.1 Preparing the Installation Environment ....................................................... 12

3.2.2 Preparing the Wiring ................................................................................. 12

3.2.3 Mounting the Control Panel....................................................................... 13

4. Wiring Instructions ......................................................... 15

4.1 Wiring Quick Reference .................................................................... 15

4.2 Wiring the System ............................................................................ 16

4.2.1 AC/DC Wiring ........................................................................................... 16

4.2.2 Battery Connection .................................................................................... 16

4.2.3 Telephone Wiring ...................................................................................... 16

4.2.4 PGM Connection ....................................................................................... 17

4.2.5 Smoke Detector Connections ..................................................................... 17

4.2.6 Zone Wiring .............................................................................................. 19

4.2.7 Sounder Connections ................................................................................ 23

4.3 Preliminary Testing ............................................................................ 23

5. Programming ................................................................... 24

5.1 Connections ..................................................................................... 24

5.2 Programming Options ....................................................................... 24

A. Battery Load Capacity .................................................... 25

B. Expansions and Accessories........................................... 26

B.1 MD-31 (RJ-31X Jack) ......................................................................... 26

B.2 SA-59 GSM Communicator ............................................................... 27

C. Reporting Codes .............................................................. 29

D. Useful Information and Tables ...................................... 31

Table of Contents

iv AuraSys™ L-2 and L-2K Installation Manual

D.1 Customer Information....................................................................... 31

D.2 Installer Information .......................................................................... 31

D.3 Device Information ........................................................................... 31

D.4 Zone Worksheet ............................................................................... 32

E. Limited Warranty ............................................................ 33

List of Figures

AuraSys™ L-2 and L-2K Installation Manual v

List of Figures

Figure 1: L-2 Control Panel ............................................................................. 8

Figure 2: L-2K Control Panel ........................................................................... 9

Figure 3: L-2/2K Mounting Template ............................................................ 14

Figure 4: L-2/2K Control Panel Components ................................................. 15

Figure 5: Battery Connection Diagram .......................................................... 16

Figure 6: Telephone Diagram ........................................................................ 17

Figure 7: PGM Wiring Diagram ..................................................................... 17

Figure 8: Smoke Detectors without Reset Mechanism ................................... 18

Figure 9: Smoke Detectors with Reset Mechanism ........................................ 19

Figure 10: Resistors ...................................................................................... 22

Figure 11: Sounder (bell) Connections .......................................................... 23

Figure 12: Rosslare's MD-62 TTL to RS-232 Converter ................................... 24

Figure 13: MD-31 Dimensions ...................................................................... 26

Figure 14: MD-31 Internal Wiring ................................................................. 26

Figure 15: MD-31 to Alarm Panel Wiring ...................................................... 27

Figure 16. Universal GSM Communicator ..................................................... 28

List of Tables

vi AuraSys™ L-2 and L-2K Installation Manual

List of Tables

Table 1: Hardwiring Schematics for Single Zone System ................................ 20

Table 2: Hardwiring Schematics for Doubled Zone System ............................ 21

Table 3: Resistor Color Scheme ..................................................................... 22

Table 4: Resistors Provided ........................................................................... 22

Table 5: Battery Load Capacity ..................................................................... 25

Table 6: Event Codes: Contact ID and SIA - Burglary and Fire ........................ 29

Table 7: Event Codes: Contact ID and SIA - Arming Events ............................ 29

Table 8: Event Codes: Contact ID and SIA - System Events ............................ 29

Notice and Disclaimer

AuraSys™ L-2 and L-2K Installation Manual vii

Notice and Disclaimer

This manual’s sole purpose is to assist installers and/or users in the safe and
efficient installation and usage of the system and/or product, and/or software
described herein.

B

EFORE ATTEMPTING TO INSTALL AND/OR USE THE SYSTEM, THE INSTALLER AND

THE USER MUST READ THIS MANUAL AND BECOME FAMILIAR WITH ALL SAFETY

REQUIREMENTS AND OPERATING PROCEDURES

.

 The system must not be used for purposes other than those for which it

was designed.

 The use of the software associated with the system and/or product, if

applicable, is subject to the terms of the license provided as part of the
purchase documents.

 ROSSLARE exclusive warranty and liability is limited to the warranty and

liability statement provided in an appendix at the end of this document.

 This manual describes the maximum configuration of the system with the

maximum number of functions, including future options. Therefore, not
all functions described in this manual may be available in the specific
system and/or product configuration you purchased.

 Incorrect operation or installation, or failure of the user to effectively

maintain the system, relieves the manufacturer (and seller) from all or any
responsibility for consequent noncompliance, damage, or injury.

 The text, images and graphics contained in the manual are for the

purpose of illustration and reference only.

 All data contained herein subject to change without prior notice.
 In no event shall manufacturer be liable for any special, direct, indirect,

incidental, consequential, exemplary or punitive damages (including,
without limitation, any and all damages from business interruption, loss of
profits or revenue, cost of capital or loss of use of any property or capital
or injury).

 All graphics in this manual are for reference only, some deviation between

the image(s) and the actual product may occur.

 All wiring diagrams are intended for reference only, the photograph or

graphic of the PCB(s) are intended for clearer illustration and
understanding of the product and may differ from the actual PCB(s).

Introduction

8 AuraSys™ L-2 and L-2K Installation Manual

1. Introduction

The AuraSys™ L-2 (and L-2K), 2/4-zone security system, is a compact and
advanced 2-zone (doubled) hardwired control panel for residential and light
commercial intrusion alarms.

There are currently two versions of the L-2 product:

 L-2 – Away/disarm using key switch
 L-2K – Local arming using numeric keypad

Figure 1: L-2 Control Panel

Introduction

AuraSys™ L-2 and L-2K Installation Manual 9

Figure 2: L-2K Control Panel

Technical Specifications and Features

10 AuraSys™ L-2 and L-2K Installation Manual

2. Technical Specifications and
Features

The AuraSys L-2 family supports a wide range of security features. This section
lists the specifications for the features that comprise the security system, as
well as the electrical and mechanical specifications of the security system.

General Attributes

Onboard dual EOL zone inputs (+
tamper detection)

2

Tamper Protection

Back and Front Cover

Zone doubling

Yes

Max. supported zones

4

Onboard PGM output

1 x OC 120 mA

Sounder output

1 x 1 Ampere

Onboard AUX output

+12 VDC 1.0 Ampere

User codes

6 (in L-2K)

Non-volatile event log size

256

Central station accounts
(primary, secondary/backup)

Yes

Private telephone numbers

Yes (3)

Electrical Characteristics

Power Supply Type

Linear type (recommended)

Input Voltage

16 VAC with 20 VA transformer
(14–18 VAC 50/60 Hz Range)

24 VDC 1A (20 to 30 VDC Range)

Input Current

Standby – 90 mA
Maximum – 258 mA

Battery BT-05

Type

SLA (Sealed Lead Acid)

Voltage

12 V

Capacity

800 mAh

Backup/Recharge Period

See Appendix

A

Technical Specifications and Features

AuraSys™ L-2 and L-2K Installation Manual 11

Battery BT-16

Type

NiMH (Nickel Metal Hydride)

Voltage

12 V

Capacity

2 Ah

Backup/Recharge Period See Appendix A

Environmental Characteristics

Operating Environment

Indoor use only

Operating Temperature Range

-15ºC to 44°C (5ºF to 111.2°F)

Operating Humidity Range

0 to 95%
(non-condensing)

RFI Protection

> 20 V/m up to 1000 MHz

Supervision

Tamper-proof system with constant
supervision

Mechanical Specifications

Dimensions
Height x Width x Depth

130 x 170 x 38 mm
(5.1 x 6.7 x 1.5 in.)

Weight
(without battery)

250 g (8.8 oz.)

Installation and Wiring

12 AuraSys™ L-2 and L-2K Installation Manual

3. Installation and Wiring

This chapter provides steps for installing the AuraSys L-2 and L-2K devices. It
also includes a Quick Guide for fast reference as well as a reference section for
wiring the system.

3.1 Installation Quick Guide

There are a number of steps to installing the unit:

Step Action Section



Preparing the Installation Environment 3.2.1



Preparing the Wiring 3.2.2



Mounting the Control Panel

3.2.3



Wiring the L-2 System 4

3.2 Installation Prerequisites

Unit installation is limited to the control panel. Installation instructions for
additional communication modules are included in appendices in this manual.
For information on installing the various detectors, please refer to the
individual manuals supplied with the detector.

3.2.1 Preparing the Installation Environment

Establish the control panel location using the following guidelines:

 Locate the control panel in a place where the temperature is within the

specified limits for operation.

 When distributing wiring, avoid putting the system wires close to house

wiring to reduce capacitive coupling of noise.

 Locate the control panel in the center of the premises to avoid long runs

to any one location.

 Install the panel 130 cm +/- 10 cm from the floor. Make sure to leave 15

cm all around the control panel for ventilation and/or wiring entry. The
panel should be installed at eye level to ease in making connections or
repairs.

3.2.2 Preparing the Wiring

The control panel provides 12 VDC up to 1 Ampere for PGM add-ons and
sensors. The maximum wire length between the panel and accessories
depends on the amount of current drawn by the accessory and the gauge of
the conductors (wires) used.

Installation and Wiring

AuraSys™ L-2 and L-2K Installation Manual 13

3.2.3 Mounting the Control Panel

The L-2 control panel family comes in two enclosed versions:

 L-2 – Plastic enclosure with 2-state key switch
 L-2K – Plastic enclosure with 6-button arming keypad

Follow the below instruction to mount the L-2 control panel family.

To mount the L-2 and L-2K panel:

1. Using a Philips head screwdriver, unscrew the enclosure screws and open

the L-2/2K enclosure.

2. Use the mounting template as shown in Figure 3 to drill holes in the wall.

3. Insert masonry anchors into the drilled holes.

4. Remove the PCB from the enclosure by gently pressing the PCB clasps to

release the PCB from the enclosure.

5. Use a flat head screwdriver to gently remove the plastic knockouts of both

the wiring hole and screw placement.

The bottom left mounting location is required for the back tamper protection,
and is the only hole without a knockout.

6. Thread the wires through the wiring hole and wire the unit as explained

ahead in Chapter

4.

7. Secure the L-2/2K panel to the wall using the supplied mounting screws.

The tamper screw is different from the mounting screws. The mounting screws
are pan head screws while the tamper screw is a unique flat head screw.

8. Place the PCB back into the back case of the enclosure; ensure that the

claps are holding the PCB in place.

9. Close and secure the enclosure using a Philips head screwdriver.

Installation and Wiring

14 AuraSys™ L-2 and L-2K Installation Manual

Figure 3: L-2/2K Mounting Template

Wiring Instructions

AuraSys™ L-2 and L-2K Installation Manual 15

4. Wiring Instructions

This section instructs you on how to wire the L-2/2K system and describes the
preliminary test performed after completing wiring the system.

4.1 Wiring Quick Reference

The PCB board and components, as well as general connections from the
control panel PCB to other panel components, are shown below:

Figure 4: L-2/2K Control Panel Components

Connector Function

+ BAT –

BT-05/16 battery connector

VIN AC/DC

Power input for AC/DC Voltage

+ Bell -

Bell/Siren connection

PGM

Programmable open collector output

+ AUX -

12 VDC power supply for external devices

Z1…Z2

Zones 1 and 2 input connections

-

Common (ground)

Line

Tip and Ring connection for phone line in

Phone

Tip and Ring connection for phone line out

PC connection

MD-62 connection to AuraSys PC software

Wiring Instructions

16 AuraSys™ L-2 and L-2K Installation Manual

4.2 Wiring the System

General connections from the PCB in the control panel to other panel
components are shown in the wiring diagram in Figure 4.

4.2.1 AC/DC Wiring

The preferable power input for the system is via an AC adaptor; however, you
have the option to connect the system to a DC power supply as well. Wire the
AC/DC power supply to the Volt IN terminal blocks (VIN + and -) located on
the PCB. Refer to Figure 4 to locate the appropriate connectors.

The AC range is between 14-18 VAC, limited up to 1.2 A. Refer to Chapter

2

for detailed electrical characteristics of the transformer.

4.2.2 Battery Connection

To connect the battery to the panel:

1. Place the battery in the battery housing within the enclosure.

2. Connect the battery’s plug to the dedicated battery power jack on the

PCB.

Figure 5: Battery Connection Diagram

See Chapter

2 for detailed battery related information.

RISK OF FIRE, EXPLOSION AND BURNING

• If replaced by incorrect battery type

• Do not disassemble, expose to excessive heat or incinerate.

• Dispose used batteries in appropriate container.

4.2.3 Telephone Wiring

See Figure 6 for the telephone wiring diagram to the control panel. It is
important to connect the control panel to a good ground, to prevent false
ringing.

Wiring Instructions

AuraSys™ L-2 and L-2K Installation Manual 17

Figure 6: Telephone Diagram

In the United States, do not connect directly to the phone line; instead use
Rosslare’s MD-31 RJ-31X jack to connect to a phone line, as explained in
Appendix A.

4.2.4 PGM Connection

The onboard PGM output is an open-collector output with a 120 mA drive
capability. The output can be connected to the AUX+, as shown in Figure 7 or
to an external power supply.

Figure 7: PGM Wiring Diagram

4.2.5 Smoke Detector Connections

Smoke detectors that have a 2-wire input are wired exactly like zones.
To support four-wire smoke detectors, the PGM output must be used as a

reset trigger (see Figure 8).
For smoke detectors with internal reset mechanism the PGM output is used for

power supervision purposes (see Figure 9).

For 4-wire fire/smoke detectors, use the following settings:

• Zone input type  Single N.O.

• Attached PGM  PG M 1

• Zone Functional Type  24-Hour Fire 4-Wires

• PGM Activation Trigger  Fire Detector Control

LINE PHONE

Wiring Instructions

18 AuraSys™ L-2 and L-2K Installation Manual

Figure 8: Smoke Detectors without Reset Mechanism

Wiring Instructions

AuraSys™ L-2 and L-2K Installation Manual 19

Figure 9: Smoke Detectors with Reset Mechanism

4.2.6 Zone Wiring

4.2.6.1 Single Zone Wiring

Refer to Table 1 for hard wiring schematics of the AuraSys L-2 system zones:

 Normally Closed
 Normally Open
 Normally Closed + End-of-Line
 Normally Closed + End-of-Line + Tamper

Wiring Instructions

20 AuraSys™ L-2 and L-2K Installation Manual

Table 1: Hardwiring Schematics for Single Zone System









4.2.6.2 Zone Doubling

Refer to Table 2 for hard wiring schematics of the AuraSys L-2 system for
doubled zones:

 Doubled Zone – Normally Closed
 Doubled Zone – Normally Open
 Doubled Zone – Normally Closed + End-of-Line
 Doubled Zone – Normally Closed + End-of-Line + Tamper

Wiring Instructions

AuraSys™ L-2 and L-2K Installation Manual 21

Table 2: Hardwiring Schematics for Doubled Zone System









4.2.6.3 Resistors

The AuraSys L-2/2K comes with 3 resistors for the various zones connections,
including tamper and EOL detection.

The resistors are: 2.2 KΩ, 4.7 KΩ and 8.2 KΩ

Wiring Instructions

22 AuraSys™ L-2 and L-2K Installation Manual

Figure 10, Table 3 and Table 4 help to understand the resistor color scheme:

Figure 10: Resistors

Stripes 1&2 represent numbers that together with stripe 3 represent the
number of zeros represents the resistor’s value in Ohm. Stripe 4 represents the
tolerance. All resistors provided by Rosslare have a 5% tolerance represented
by the color Gold. To read the resistor number, hold the unit with the gold
stripe on the right.

The color scheme is as follows:

Table 3: Resistor Color Scheme

Black

0

Brown

1

Red 2

Orange 3

Yellow 4

Green

5

Blue 6

Violet 7

Grey 8

White

9

Based on the above color scheme, the resistors provided are as follows:

Table 4: Resistors Provided

Color
Resisitor

  

2.2K

Red Red Red

4.7K

Yellow Violet Red

8.2K

Grey Red Red



  

Wiring Instructions

AuraSys™ L-2 and L-2K Installation Manual 23

4.2.7 Sounder Connections

Sounder connections are shown in Figure 11. Total current drawn from the
sounder output cannot exceed 1 A.

Figure 11: Sounder (bell) Connections

4.3 Preliminary Testing

Once the control panel has been properly installed and wired:

1. Physically check the panel to ensure that there are no shorted or open

connections.

2. Power up the system.

All LEDs flash in sequence.

3. Verify that all LEDs were lit.

After programming the system as explained in Chapter 5, perform the
following preliminary tests:

1. Perform a walk test for each of the zones.

2. Verify that the corresponding LEDs are lit.

3. Arm/disarm the system to verify that the system behaves according to the

programmed settings.

4. Initiate a call to the call center or to a private phone to test

communication.

Programming

24 AuraSys™ L-2 and L-2K Installation Manual

5. Programming

The AuraSys L-2 can only be programmed using the AuraSys Lite Remote
Programmer PC software.

There are two ways to connect the unit to a PC:

 Directly using Rosslare’s MD-62 TTL to an RS-232 converter
 Remotely via the telephone line

You can also update the unit’s firmware using the AuraSys Lite Remote
Programmer PC software with a direct connection using HyperTerminal.

5.1 Connections

To connect the AuraSys L-2 panel to the PC directly:

1. Using the Rosslare's MD-62 TTL to RS-232 converter, connect the MD-62

to the L-2/2K’s PC serial port.

Figure 12: Rosslare's MD-62 TTL to RS-232 Converter

If your computer does not have a serial port, use Rosslare’s MD-C24 USB to RS­232 converter.

2. Connect the RS-232 connector to the PC.

3. Ensure that the red wire in the cable’s 10-pin connector is connected to

Pin Number 1 on the PCB male connector.

4. Run the AuraSys Lite Remote Programmer PC software.

To connect the AuraSys L-2 panel to the PC remotely:

1. Connect the L-2/2k to the phone line using the RJ-11 cable.

2. Run the AuraSys Lite Remote Programmer PC software.

3. Ensure that the unit’s phone number is assigned in the application.

4. Ensure the computer running AR-P02 has a modem connection.

5.2 Programming Options

Refer to the AuraSys Lite Software Manual for detailed instructions on
connecting to the panel and other available options.

Battery Load Capacity

AuraSys™ L-2 and L-2K Installation Manual 25

A. Battery Load Capacity

Table 5: Battery Load Capacity

Panel Load Capacity BT-05 (800mAh) BT-16 (2 Ah)

Standby
Current

Maximum
Current

Standby
Current

Maximum
Current

L-2 Low 1 x PIRs 10 Hours 3.2 Hours 25 Hours 8.0 Hours
L-2K Low 1 x PIRs 10 Hours 3.2 Hours 25 Hours 8.0 Hours

L-2 Full 2 x PIRs 8.8 Hours 3.1 Hours 22.2 Hours 7.8 Hours
L-2K Full 2 x PIRs 8.8 Hours 3.1 Hours 22.2 Hours 7.8 Hours

Expansions and Accessories

26 AuraSys™ L-2 and L-2K Installation Manual

B. Expansions and Accessories

B.1 MD-31 (RJ-31X Jack)

Even though the RJ31X jack has additional connections, typically only four
wires are used; two for connecting to the outside phone line (T and R), and
two for connecting to the inside phone lines (T1 and R1).

The MD-31 has eight screw terminals inside the housing. This makes it easy to
connect the outside and inside lines.

To connect the MD-31:

1. Connect the lines as shown in Figure 13 and Figure 14.

The outside and inside lines can come into the jack from within the wall
behind the jack, or into either, or both, sides of the jack.

Figure 13: MD-31 Dimensions

Figure 14: MD-31 Internal Wiring

 Out to internal Phone Line – Ring
 Out to internal Phone Line – Tip
 From Phone Company – Ring
 From Phone Company – Tip

Expansions and Accessories

AuraSys™ L-2 and L-2K Installation Manual 27

Color coding in the Figure 15 may vary based on the installer’s wiring;
however, these are the standard color coding based on a typical
installation.

When connected as shown (and nothing is plugged into the jack), the
internal phones should work.

2. Replace the cover on the jack.

The unit can now be connected to the security system.

Figure 15: MD-31 to Alarm Panel Wiring

3. Connect the 50-cm cord to the alarm panel:

 Yellow to "R" or "Ring" contact (Ring, from phone company)
 Green to "T" or "Tip" contact (Tip, from phone company)
 Brown to "R1" contact (Ring, To inside phones)
 White to "T1" contact (Tip, to inside phones)

4. Plug the 50-cm cord into the MD-31 and test communication.

B.2 SA-59 GSM Communicator

The SA-59 is a universal GSM reporting unit and communicator. When it is
connected to an alarm panel, the SA-59 operates as a GSM backup unit to the
PSTN line, enabling incoming and outgoing calls to be redirected to the GSM
network if the PSTN line fails. Since the SA-59 simulates a telephone line, it
makes no difference whether the device to which it is connected is a GSM or a
land line.

The built-in SA-59 GSM module connects via the PSTN line to check for phone
communication type availability. If there is no PSTN line, the SA-59
automatically switches the call from PSTN line to GSM.

When the SA-59 is connected to a telephone line (Line IN), the SA-59 tunnels
the device to a land line to make a call. If the land line is cut or not

Expansions and Accessories

28 AuraSys™ L-2 and L-2K Installation Manual

functioning, all communications go via the GSM network without the need for
any special additional settings.

If the SA-59 is not connected to a land line, all communications take place via
the GSM network.

Figure 16. Universal GSM Communicator

Reporting Codes

AuraSys™ L-2 and L-2K Installation Manual 29

C. Reporting Codes

Table 6, Table 7, and Table 8 provide a listing of the Contact ID (CID) codes
used to communicate with the CMS.

Table 6: Event Codes: Contact ID and SIA - Burglary and Fire

Burglary and Fire Event/Restore

Description CID Description CID

Medical Alarm (Restore) R100 Shorted (Event) E142

Emergency Alarm (Event) E101 Wired Tamper (Event) E144

Fire (Event) E110 Wired Tamper (Restore) R144

Fire (Restore) R110 Any Zone Trouble (Event) E380

RF Panic (Event) E120 Any Zone Trouble (Restore) R380

Alarm – 24-hour Silent (Event) E122 RF Supervisor (Event) E381

Alarm – 24-hour Silent (Restore) R122 RF Supervisor (Restore) R381

Burglary (Event) E130 RF Tamper (Event) E383

Burglary (Restore) R130 RF Tamper (Restore) R383

Alarm – 24-hour Audible (Event) E133 RF Low battery (Event) E384

Alarm – 24-hour Audible
(Restore)

R133 RF Low battery (Restore) R384

Open (Event) E141

Table 7: Event Codes: Contact ID and SIA - Arming Events

Arm and Disarm Events

Description CID Description CID

Duress E121 Key Switch Disarm E409

Disarm E401 Key Switch Arm Away R409

Arm Away R401 Forced Arm Away R423

Alarm Cancel E406

Table 8: Event Codes: Contact ID and SIA - System Events

System Events

Description CID

Panel Remote Tamper (Event) E137

Panel Remote Tamper (Restore) R137

Panel Trouble E300

Reporting Codes

30 AuraSys™ L-2 and L-2K Installation Manual

System Events

Description CID

Panel AC Fail (Event) E301

Panel AC Fail (Restore) R301

Panel Low battery (Event) E302

Panel Low battery (Restore) R302

Aux Bell Over (Event) E312

Aux Bell Over (Restore) R312

REM Module Missing (Event) E330

REM Module Missing (Restore) R330

RF Jamming (Event) E344

RF Jamming (Restore) R344

Communication Fail (Event) E354

Communication Fail (Restore) R354

Swinger Over E377

Zone Bypass E570

Zone Un-bypass R570

Fire Zone Bypass E571

Fire Zone Un-bypass R571

CMS Test E602

Listen In Start E606

Inaccurate Time (Event) E626

Inaccurate Time (Restore) R626

Useful Information and Tables

AuraSys™ L-2 and L-2K Installation Manual 31

D. Useful Information and Tables

There are several programming worksheets in this chapter so that the installer
can keep a record of what has been done during the initial programming.

D.1 Customer Information

Customer: __________________________________________________________
Address: ___________________________________________________________
___________________________________________________________________
___________________________________________________________________
Telephone: ______________________ Installation Date: ____________________

D.2 Installer Information

Name: _____________________________________________________________
Address: ___________________________________________________________
___________________________________________________________________
___________________________________________________________________
Telephone: ______________________ Installer’s Code: ____________________

D.3 Device Information

Module Name Description Location

Useful Information and Tables

32 AuraSys™ L-2 and L-2K Installation Manual

D.4 Zone Worksheet

Print out this Zone Worksheet and use it to plan programming values for each zone.

Zone Input

Type

Partition PGM#

Crossing

Paired
Zone

Response
time
(in100
ms)

Chime Alarm

Verification

PGM

Activation

on Zone
Violation

No-

Activity

Monitoring

Zone
Crossing/
Walkthrough

01
02

03
04

Limited Warranty

AuraSys™ L-2 and L-2K Installation Manual 33

E. Limited Warranty

The full ROSSLARE Limited Warranty Statement is available in the Quick Links
section on the ROSSLARE website at www.rosslaresecurity.com.

Rosslare considers any use of this product as agreement to the Warranty Terms
even if you do not review them.

AuraSys™ L-2

0706-0960326+01

Asia Pacific, Middle East,
Africa

Rosslare Enterprises Ltd.
Kowloon Bay, Hong Kong
Tel: [phone]
Fax: [phone]
[e-mail]

United States and Canada

Rosslare Security Products, Inc.
Southlake, TX, USA
Toll Free: [phone]
Local: [phone]
Fax: [phone]
[e-mail]

Europe

Rosslare Israel Ltd.
Rosh HaAyin, Israel
Tel: [phone]
Fax: [phone]
[e-mail]

Latin America

Rosslare Latin America
Buenos Aires, Argentina
Tel: [phone]
[e-mail]

China

Rosslare Electronics (Shenzhen) Ltd.
Shenzhen, China
Tel: [phone]
Fax: [phone]
[e-mail]

India

Rosslare Electronics India Pvt Ltd.
Tel/Fax: [phone]
Mobile: [phone]
[e-mail]