Rosslare 20A302 Users Manual

Rosslare

Installation Instructions

Model Series AY-Q12

The AY-Q12 Prox Reader is a weather and
vandal resistant RFID proximity card
reader, to be installed for use with access
control systems.

These Installation Instructions contain the
following information:

* Mounting Instructions
* Wiring Instructions
* Operation Instructions

MOUNTING INSTRUCTION

To mount the Reader, perform the following:

1.

Determine an appropriate mounting position for the Reader.

2.

Peel off the back of the self-stick mounting label template
included with the unit and place at the desired mounting position.

3.

Using the template as a guide, drill two holes (hole size is
indicated on mounting template) for mounting the Reader to the
surface. Drill a 7/16" (10mm) hole for the cable. If mounting on
metal, place a grommet around the edge of the hole.

4.

Remove the case screw and slide the rear case away from the front
case. (See diagram below)

5.

Drill holes into the back of the rear metal case according to how
you want to mount the reader. (See Diagram below)
Attach the reader to the controller.

6.
Screw the readers rear case to its mounting location and return the

7.
front case onto the mounted rear case.
Secure the front cover by using the supplied security screw in the

8.
controllers accessories kit. An L-Shaped tool is provided for use
when tightening the security screw.

US Gang Box
There are two hole
indicators on the back of
the metal cover
specifically for the US
Gang Box. (Shown
marked as A)

4 Screw Custom
There are four indicators
on the back. (Shown
marked as B)

-1-

A

B

B

B

CAUTION!

DO NOT DRILL

This is the Tamper Lens

B

A

03/02

Card Readers are to be used with control panels whose power
supply is UL Listed Class 2 or equivalent.

WIRING INSTRUCTION

The Prox Reader is supplied with an 18-inch pigtail, having a 6­conductor cable. To connect the Reader to the Controller, perform
the following steps:

Prepare the Reader cable by cutting the cable jacket back 1

1.
inches and strip the wires inch.
Prepare the Controller cable by cutting the cable jacket back 1

2.
inches and strip the wires inch.
Splice the Reader pigtail wires to the corresponding Controller

3.

1

/2

1

/2

1

1

wires and cover each connection (see Figure 2).
If the tamper output is being utilized, connect the purple wire to

4.
the correct input on the Controller.
Trim and cover all conductors that are not used.

5.

Figure 2 below shows how you should wire the Reader to the
Controller.

COLOR

Red
Black
White

Green
Brown
Purple

Cable Notes:

1.

The individual wires coming out of the reader are color coded according
to the recommended Wiegand standard.

When using a separate power supply for the Reader, this supply and the

2.
Controller's power supply must have a common ground.

The cable shield wire on the Reader should be attached to an Earth

3.
ground (best) or signal ground connection at the panel or power supply
end of the cable. This configuration is best for shielding the Reader
cable from external interference.

WIEGAND

OUTPUT
DC+Input

Ground

Data 1
Data 0

LED Control

Tamper

Figure 2

OPERATION INSTRUCTION

The Reader should be tested after wiring it to a power supply and the
Controller. Do this by performing the following steps:

1.

Power up the Reader. The LED and Beeper will activate three
times. This indicates that the Reader is working properly.

Present the appropriate type of proximity card to the Reader. The

2.
LED will momentarily flash green and a short beep will be
emitted. This indicates that the card was read properly by the Prox
Reader..

3.

After the card data is processed by the Controller, the Controller
can then turn the LED green. Refer to the Controller description
of the LED operation if the Reader LED is controlled by the
Controller.

SPECIFICATIONS

/4

Power Supply Type

Operating Voltage Range

/4

Maximum Input Current

Tamper Output

Maximum Cable Distance
to Controller

RF Modulation

Output Modulation 26-Bit Wiegand

*

Card Read Distance:

Regulatory Approvals:

Operating Temp. Range:

Operating Humidity:

Dimensions:

Measured using Rosslare Proximity Card (P/N AT-11/14) or

*

4.72” (120mm) L x 3” (76mm) W x 1” (27mm) D

equivalent. Range also depends on electrical environment and/or
proximity to metal.

Suitable for outdoor use

Linear type recommended

5 - 16 VDC

Standby : 35 mA

Read : 100 mA

Open collector, active low,
max. sink current is 16 mA

150 meters (500 ft.)

ASK

2” (55mm)

USA : UL 294 & FCC Part 15B

Europe : CE Listed

ooo o

-31 C to 63 C (-25 F to 145 F)

0 to 95% (non condensing)

UL File Number: BP9264

0706-0820022-00

-1-

-2-

-3-

Rosslare

Installation Instructions

Model Series AY-Q14

The AY-Q14 Prox Reader is a weather and
vandal resistant RFID proximity card
reader, to be installed for use with access
control systems.

These Installation Instructions contain the
following information:

* Mounting Instructions
* Wiring Instructions
* Operation Instructions

MOUNTING INSTRUCTION

To mount the Reader, perform the following:

1.

Determine an appropriate mounting position for the Reader.

2.

Peel off the back of the self-stick mounting label template
included with the unit and place at the desired mounting position.

3.

Using the template as a guide, drill two holes (hole size is
indicated on mounting template) for mounting the Reader to the
surface. Drill a 7/16" (10mm) hole for the cable. If mounting on
metal, place a grommet around the edge of the hole.

4.

Remove the case screw and slide the rear case away from the front
case. (See diagram below)

5.

Drill holes into the back of the rear metal case according to how
you want to mount the reader. (See Diagram below)
Attach the reader to the controller.

6.
Screw the readers rear case to its mounting location and return the

7.
front case onto the mounted rear case.
Secure the front cover by using the supplied security screw in the

8.
controllers accessories kit. An L-Shaped tool is provided for use
when tightening the security screw.

US Gang Box
There are two hole
indicators on the back of
the metal cover
specifically for the US
Gang Box. (Shown
marked as A)

4 Screw Custom
There are four indicators
on the back. (Shown
marked as B)

-1-

A

B

B

B

CAUTION!

DO NOT DRILL

This is the Tamper Lens

B

A

03/02

Card Readers are to be used with control panels whose power
supply is UL Listed Class 2 or equivalent.

WIRING INSTRUCTION

The Prox Reader is supplied with an 18-inch pigtail, having a 6­conductor cable. To connect the Reader to the Controller, perform
the following steps:

Prepare the Reader cable by cutting the cable jacket back 1

1.
inches and strip the wires inch.
Prepare the Controller cable by cutting the cable jacket back 1

2.
inches and strip the wires inch.
Splice the Reader pigtail wires to the corresponding Controller

3.

1

/2

1

/2

1

1

wires and cover each connection (see Figure 2).
If the tamper output is being utilized, connect the purple wire to

4.
the correct input on the Controller.
Trim and cover all conductors that are not used.

5.

Figure 2 below shows how you should wire the Reader to the
Controller.

COLOR

Cable Notes:

1.

The individual wires coming out of the reader are color coded according
to the recommended Wiegand standard.

When using a separate power supply for the Reader, this supply and the

2.
Controller's power supply must have a common ground.

The cable shield wire on the Reader should be attached to an Earth

3.
ground (best) or signal ground connection at the panel or power supply
end of the cable. This configuration is best for shielding the Reader
cable from external interference.

Red
Black
White

Green
Brown
Purple

CLOCK & DATA

OUTPUT

DC+Input

Ground

Clock

Data

LED Control

Tamper

Figure 2

OPERATION INSTRUCTION

The Reader should be tested after wiring it to a power supply and the
Controller. Do this by performing the following steps:

1.

Power up the Reader. The LED and Beeper will activate three
times. This indicates that the Reader is working properly.

Present the appropriate type of proximity card to the Reader. The

2.
LED will momentarily flash green and a short beep will be
emitted. This indicates that the card was read properly by the Prox
Reader..

3.

After the card data is processed by the Controller, the Controller
can then turn the LED green. Refer to the Controller description
of the LED operation if the Reader LED is controlled by the
Controller.

SPECIFICATIONS

/4

Power Supply Type

Operating Voltage Range

/4

Maximum Input Current

Tamper Output

Maximum Cable Distance
to Controller

RF Modulation

Output Modulation Clock and Data

*

Card Read Distance:

Regulatory Approvals:

Operating Temp. Range:

Operating Humidity:

Dimensions:

Measured using Rosslare Proximity Card (P/N AT-11/14) or

*

4.72” (120mm) L x 3” (76mm) W x 1” (27mm) D

equivalent. Range also depends on electrical environment and/or
proximity to metal.

Suitable for outdoor use

Linear type recommended

5 - 16 VDC

Standby : 35 mA

Read : 100 mA

Open collector, active low,
max. sink current is 16 mA

150 meters (500 ft.)

ASK

2” (55mm)

USA : UL 294 & FCC Part 15B

Europe : CE Listed

ooo o

-31 C to 63 C (-25 F to 145 F)

0 to 95% (non condensing)

UL File Number: BP9264

0706-0820023-00

-1-

-2-

-3-