Rosslare 10F302 Users Manual

WHAT IS THE ADEMCO OmniProx™ READER?
Visit www.omniprox.com for the latest information and
Mount the reader with the appropriate screws (not
Card Reader Models OP10/20/30/40/45/90 are to be
The individual wires coming out of the reader are color
If either 5 or 12 volts are available, use 12 volts for better
y for the reader, the
reader, power supply and host must have a common
The recommended cable depends on the distance from the reader to the host. See Table 1 on the next page for the correct wire gage based upon distance. Larger wire
eptable. The wire must be stranded with an overall shield, either foil or braided. If the tamper is not being used, 5 conductor cable is required; otherwise 6
The OmniProx Reader is an RFID proximity card reader to be installed for use with access control systems.
These installation instructions contain the following information:
Mounting Instructions
Connecting the reader to the host
Testing and operation of the reader
Installation Instructions
5. Route the interface cable from the reader and/or
Check all electrical codes for proper installation.
U
used with control panels whose power supply is UL
L
listed Class 2 or equivalent.
K5336 Rev. 6, 07/2001
OmniProx™ Reader
Model Series OP10/20/30/40/45/90
power supply to the host. A linear type power supply is recommended.
HOW TO MOUNT THE READER
technical support.
Figure 1 shows the front view of the OmniProx. When mounting models OP10/20/30/40/45, the snap-off cover must be removed to access the screw holes.
Figure
The model OP90 uses a security screw on the bottom of the reader to secure the cover. Remove this security screw using the supplied tool. Then slide the back plate down slightly and then lift it up from the bottom. Select the desired mounting holes and drill them out.
supplied) as indicated on the template.
To surface mount the reader, perform the following:
1. Determine an appropriate mounting position for the reader.
2. Peel off the back of the self-stick mounting label template included with the unit and place at the desired mounting position. (Additional templates can be downloaded from www.omniprox.com.)
3. Using the template as a guide, drill two holes (hole size is indicated on mounting template) for mounting the reader to the surface.
4. Drill a 1/2” (13 mm) hole for the cable. If mounting on metal, place a grommet or electrical tape around the edge of the hole.
HOW TO CONNECT THE READER TO THE HOST
The OmniProx Reader is supplied with an 18-inch pigtail, having a 6-conductor cable. To connect the reader to the host, perform the following steps:
1. Prepare both the reader cable and host cables by cutting the cable jacket back 1¼ inches and strip the wires ½ inch.
2. Splice the reader pigtail wires to the corresponding host wires and cover each connection (see Figure 2).
3. If the tamper output is being utilized, connect the purple wire to the correct input on the host.
4. Trim and cover all conductors that are not used.
Figure 2 below shows how you should wire the reader to the host.
Figure 2
Wiring Notes:
1.
coded according to the recommended Wiegand standard.
2. performance.
3. When using a separate power suppl
-1-
ground.
4.
gauges are acc
conductor cable is required.
The cable shield wire on the reader should be attached to
round (best) or signal ground connection at the panel or power supply end of the cable. This configuration is best for shielding the reader cable from external
5.
an Earth g
interference.
TABLE 1: WIRE GAGE SPECIFICATIONS
Distance Gage 5 Conductor 6 Conductor
 200 ft. (61m) 22 Alpha 1295C Alpha 1296C 300 ft. (91m) 20 Alpha 58126 Alpha 58126  500 ft. (153 m) 18 Alpha 58136 Alpha 58136
Note: Recommended cable is only a guideline, use any manufacturer that meets the gage and shield specifications.
HOW TO TEST AND OPERATE THE READER
The reader should be tested after wiring it to a power supply and the host. Do this by performing the following steps:
1. Power up the reader. The LED and beeper will activate three times. This indicates that the reader is working properly.
2. Present the appropriate type of ID card to the reader. (See Table 2 for the correct card type based on the reader model.) The LED will momentarily flash green and a short beep will be emitted. This indicates that the card was read properly by OmniProx.
3. After the card data is processed by the host, the host can then turn the LED green or yellow. Refer to the host description of the LED operation if the reader LED is controlled by the host.
Table 2: Model Number vs. Feature Matrix
Model
Number
OP10-FW AY-K10 HID Wiegand 3” OP10-AW AY-K12 ADEMCO Wiegand 3” OP20-FW AY-J10 HID Wiegand 4” OP20-AW OP30-FW AY-L10 HID Wiegand 5” OP30-AW AY-L12 ADEMCO Wiegand 5” OP40-FW AY-H10 HID Wiegand 4” OP40-AW AY-H12 ADEMCO Wiegand 4” OP45-FW AY-M10 HID Wiegand 4” OP45-AW AY-M12 ADEMCO Wiegand 4” OP90-FW AY-Qxx HID Wiegand 1.5”
UL Listing
Part #
Card Type
Output
Format
AY-J12 ADEMCO Wiegand 4”
Read Range (Max.)
*
Model
Number
UL Listing
Part #
Card Type
Output
Format
Read Range (Max.)
*
TABLE 1: WIRE GAGE SPECIFICATIONS
Distance Gage 5 Conductor 6 Conductor
 200 ft. (61m) 22 Alpha 1295C Alpha 1296C 300 ft. (91m) 20 Alpha 58126 Alpha 58126  500 ft. (153 m) 18 Alpha 58136 Alpha 58136
Note: Recommended cable is only a guideline, use any manufacturer that meets the gage and shield specifications.
HOW TO TEST AND OPERATE THE READER
The reader should be tested after wiring it to a power supply and the host. Do this by performing the following steps:
1. Power up the reader. The LED and beeper will activate three times. This indicates that the reader is working properly.
2. Present the appropriate type of ID card to the reader. (See Table 2 for the correct card type based on the reader model.) The LED will momentarily flash green and a short beep will be emitted. This indicates that the card was read properly by OmniProx.
3. After the card data is processed by the host, the host can then turn the LED green or yellow. Refer to the host description of the LED operation if the reader LED is controlled by the host.
Table 2: Model Number vs. Feature Matrix
Model
Number
OP10-FW AY-K10 HID Wiegand 3” OP10-AW AY-K12 ADEMCO Wiegand 3” OP20-FW AY-J10 HID Wiegand 4” OP20-AW OP30-FW AY-L10 HID Wiegand 5” OP30-AW AY-L12 ADEMCO Wiegand 5” OP40-FW AY-H10 HID Wiegand 4” OP40-AW AY-H12 ADEMCO Wiegand 4”
UL Listing
Part #
Card Type
Output
Format
AY-J12 ADEMCO Wiegand 4”
Read Range (Max.)
*
-2-
Loading...
+ 3 hidden pages