Rosieres RGM9095IN User Manual

FREE STANDING OVEN

90x60 Gas & Electrical Oven 90x60cm Cuisinière à Table Gaz et Four Électrique

RGM9095IN

USER MANUAL

MANUEL D’INSTRUCTIONS

Dear User,

Our objective is to make this product provide you with the best output which is manufactured in our modern facilities in a careful working environment, in compliance with total quality concept.

Therefore, we suggest you to read the user manual carefully before using the product and, keep it permanently at your disposal.

Note: This user manual is prepared for more than one model. Some of the features specied in the Manual may not be available in your appliance.

All our appliances are only for domestic use, not for commercial use.

* Mark the products as option.

“THIS APPLIANCE SHALL BE INSTALLED IN ACCORDANCE WITH THE REGULA TIONS FORCE AND ONLY USED IN A WELL VENTILATED SPACE. READ THE INSTRUCTIONS BEFORE INSTALLING OR USING THIS APPLIANCE”

“Conforms with the WEEE Regulations."

CONTENTS

Important Warnings

4 Introduction Of The Appliance 7 Important Warnings 8 Electrical Wiring Scheme 9 Gas Hose Passage Way 10 Chain Lashing Illustration 11 Installation Of Your Oven 11 Technical Features Of Your Oven 12 Reduced Flame Gas Cock Adjustment 13 Reduced Gas Flow Rate Setting For Hob Taps 13 Description Of Oven 14 Description Of The Control Panels 15 Using The Burner Groups 15 Installation Of The Oven Feet 16 Splash Back and Telescopic Leg 17 Using Oven Section 18 Catalytic Walls 19 Chicken Roasting 19

Cleaning And Maintenance Of The

Oven’s Front Door Glass 20 Changing The Oven Lamp 20 Maintenance And Cleaning 21 Installation Of The Oven Door 22 Accesories 23 Removal Of The Lower And Upper Burner And Installation Of The Injector To The Gas Oven 24 If Your Oven Does Not Operate 25 Environmentally-Friendly Disposal and Package Information 25

IMPORTANT WARNINGS

1.WARNING: To avoid electrocution, ensure that the electri-

cal circuit of the product is open before replacing the lamp.

2.WARNING:Before touching the connection terminals,

all supply circuit should be disconnected.

3.WARNING:While operating the grill, the reachable sec-

tions can be hot. Keep the children away.

4.WARNING:Any inadvertent cooking made with fats and

oils can be dangerous and cause re.

5.WARNING:Risk of re; do not store the food materials

on the cooking surface.

6.WARNING:If the surface is cracked, unplug the device

to prevent any risk of electric shock.

7.WARNING:During usage the reachable sections can be

hot. Keep the small children away.

8.WARNING:The appliance and its reachable sections

become hot during usage.

9.The setting conditions of this appliance is indicated

on the label. (Or data tag)

10.This appliance is not connected to a combustion

product discharge system.This appliance shall be connected and installed as per the applicable installation legislation. Consider the requirements related with ventilation.

11.Using a gas hob will release humidity and combus-

tion products in the room where it resides. Especially during when the appliance in use, ensure that the kitch-

en is well ventilated and retain the natural ventilation holes or install a mechanical ventilation system. (Hood on top of the oven) Sustained usage of the appliance may require additional ventilation. For example opening a window or if available, increasing the ventilation level of a mechanical ventilation system.

12.The reachable sections can become hot when the

grill is used. Keep the small children away.

13.WARNING:The appliance is intended for cooking only.

It must not be used for other purposes like room heating.

14.There are additional protective equipment to pre-

vent inadvertent touching to the oven doors. This equipment should be installed if there are children.

15.“This appliance should be installed as per regula-

tions and in well-ventilated location only. Read the instructions before installing or operating the appliance.”

16.“Before placing the appliance check the local con-

ditions (gas type and gas pressure) and ensure that the settings of the appliance is appropriate.”

17.“These instructions are applicable for countries of

which symbols are indicated on the appliance. If the country symbol is not available on the appliance, in order to adapt the appliance to the conditions of such country, the technical instructions should be read.”

18.“Do not operate the system for more that 15 sec-

onds. If the burner does not ignite at the end of 15 seconds stop the operation of the system and open the

section door and/or wait for at least 1 minute before igniting the burner.

19.Do not use steam cleaners to clean the appliance.

20.Before opening the oven door clean the remnants

on it. Before closing the oven door, let it cool.

21.NEVER try to extinguish a re with water, rst dis-

connect the mains supply and then using, for example

a lid or blanket, cover the re.

22.Do not use hard and abrasive cleaning agents or

hard metal scrapers to clean the oven door glass as they may scratch and shatter the surface.

23.After placing a dish, ensure that the door is rmly

closed.

24.Unless continuous supervision is provided, the

children of age 8 or below should be kept away.

25.Pay attention for not to touch the heating elements.

26.This appliance can be used by children aged from

8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.

INTRODUCTION OF THE APPLIANCE

3 4 5 6

12 13 14 15 16

19 20

21 22 23

1. Middle Burner

2. Middle Burner

3. Trivet

4. WOK Burner

5. Large Burner

6. Auxiliary Burner

7. Hot Plate

8. WOK Burner

9. Glass Door

10. Control Panel

11. Led Lamp

12. Oven Control Knobs

13. Digital Timer

14. Hob Control Knobs

15. Wire Grill

16. Deep Tray

17. Door

18. Handle

19. Lower Cabinet Door

20. Telescopic Leg

21. Lamp

22. Grill

23. Chicken Roasting

24. Deep Tray

IMPORTANT WARNINGS Electrical Connection and Security

1. Your cooker is adjusted in compliance with 220-240V, 50/60Hz for

mono phase or 220-240V / 380-415V, 50/60Hz for three phase and 16 or 32 Ampere electric supply. If the mains is different from these values, contact your authorized service.

2. Electrical connection of the oven should only be made by the sockets

with earth system installed in compliance with the regulations. If there is no proper socket with earth system in the place where the oven will be

installed, immediately contact a qualied electrician. Manufacturer shall

never be responsible from the damages that will arise because of the sockets connected to the appliance with no earth system.

3. Electrical cable should not touch the hot parts of the appliance.

4. For disconnection from the supply mains having a contact separation

in all poles that provide full disconnection, must be incorporated in xed

wiring in according with the wiring rules.

Gas Connection and Security

1. Before your appliance is connected to the gas supply, ensure that

the gas category and pressure specications shown in the data plate corresponds with your gas supply. If necessary call authorized service for adjusting to gas category.

2. This appliance shall be installed in accordance with the regulations

in force and only used in a well ventilated space. Read the instructions before installing or using this appliance. In the interest of safety this appliances must be installed and / or serviced by a competent person as stated in the gas safety regulations current editions.

3. The appliance must not be installed in a room without a window or

other controllable opening. If is installed in a room without a door which opens directly to the outside, a permanent opening is required. The air circulation should be 2 m3/h per kW of burners.

4. The gas connection should be performed from the right or left. For

this reason, change the hose nozzle, plug and the seals.

5. Please use exible hose for gas connection.

6. If you make a connection with a exible metal hose, locate a seal

between the main gas pipes.

7. The inner diameter of the exible hose, which the butane hose nozzle

is connected, should be 6mm for the house-type gas tubes. The inner

diameter of the exible hose, which the natural hose nozzle is connect-

ed, should be 15mm.The hose should tightly be tted to the hose nozzle

by squeezing with a clamp. The hose should be replaced before its last expiry date.

8. Caution! Make the oven connection to the gas inlet valve, the hose

length must be short and be sure that there is no leakage. The exible

hose used should not be longer than 125 cm for safety.

9. RE-INSPECT THE GAS CONNECTION.

10. When placing your oven to its location, ensure that it is at the coun-

ter level. Bring it to the counter level by adjusting the feet if necessary.

DO NOT MAKE GAS HOSE and ELECTRICAL CABLE OF YOUR OVEN GO THROUGH THE HEATED AREAS, ESPECIALLY THROUGH THE REAR SIDE OF THE OVEN. DO NOT MOVE GAS CONNECTED OVEN. SINCE THE FORCING SHALL LOOSEN THE HOSE, GAS LEAKAGE MAY OCCUR.

ELECTRICAL WIRING SCHEME

FUSE SWITCH (25A/40A)

3x4mm²

610mm

Live Phase

H05 VV-F 3G 4mm² H05 VV-F 5G 1.5mm² H05 VV-F 4G 1.5mm² H05 VV-F 3G 1.5mm²

CONSUMER UNIT

JUNCTION BOX

220-240V~50/60Hz 220-240V~50/60Hz

400V 3N~50/60Hz 400V 2N~50/60Hz

Neutral Neutre

Earth Terre Erdung

Neutral Neutre

Earth Terre Erdung

Neutral Neutre

Earth Terre Erdung

Neutral Neutre

Earth Terre Erdung

GAS HOSE PASSAGE WAY

1. Connect the appliance to the gas piping tap in shortest possible route

and in a way that ensure no gas leakage will occur.

2. In order to carry on a tightness and sealing safety check ensure that

the knobs on the control panel are closed and the gas cylindir is open.

3. While performing a gas leakage check, never use any kind of lighter,

match, cigarette or similar burning substance.

4. Apply soap bubble on the connection points. If there is any kind of

leakage then it will cause bubbling.

5. While inserting the appliance in place ensure that it is on the same

level with the worktop. If required adjust the legs inorder the make level with the worktop.

6. Use the appliance on a level surface and in a well ventilated environ-

ment.

Figure 1 Figure 2

CHAIN LASHING ILLUSTRATION

Before using the appliance, in order to ensure safe use, be sure to x the appliance to the wall using thechain and hooked screw supplied. Ensure that the hook is screwed into the wall securely.

INSTALLATION OF YOUR OVEN

600-650mm min.

850 mm min.

900 mm min.20 mm 20 mm

TECHNICAL FEATURES OF YOUR OVEN

Specications 90x60 Cooker

Outer width 900mm Outer depth 610mm Outer height 925mm Inner width 765mm Inner depth 450mm Inner height 370mm Lamp power 15W Bottom heating element 2000W Top heating element 1500W Grill heating element 2500W Turbo Heating element 1250W x 2 Supply voltage 220-240V, 50/60Hz

BURNER SPECIFICATIONS

Wok Burner

Rapid Burner

Semi-rapid Burner

Auxiliary Burner

Oven Burner

Grill Burner

G20,20 /

G25,25 mbar

Gas Naturel

Injector mm 1.40 0.96 Power KW 3.50 3.50 Injector mm 1.15 0.85 Power KW 2.90 2,90 Injector mm 0.97 0.65 Power KW 1.70 1.70 Injector mm 0.72 0.50 Power KW 0,95 0.95 Injector mm 1.45 1.00 Power KW 4.00 4.00 Injector mm 1.20 0.85 Power KW 2.70 2.70

G30,28-30

G31,37 mbar

LPG

REDUCED FLAME GAS COCK ADJUSTMENT

1. Please use driver with special head for removed and install nozzle as (gure-3)

2. Please remove nozzle (gure-4) from burner with special nozzle driver

and install new nozzle (gure-5)

Figure 3 Figure 4 Figure 5

REDUCED GAS FLOW RATE SETTING FOR HOB TAPS

1. Ignite the burner that is to be adjustment and turn the knob to the

reduced position.

2. Remove the knob from the gas tap.

3. Use an appropriately sized screwdriver to adjust the ow rate adjust-

ment screw.

For LPG (Butane - Propane) turn the screw clockwise. For the naturel gas, you should turn the screw counter- clockwise once.

“The normal length of a straight ame in the reduced position should

be 6-7 mm.

4. If the ame is higher then the desired position, turn the screw clock-

wise. If it is smaller turn anticolockwise.

5. For the last control, bring the burner both to higt-ame and reduced

positions and check whether the ame is on or off.

Depending on the type of gas tap used in your appliance the adjustment screw position may vary.

To adjust your oven acc. to the gas type, make the adjustment for re-

duced ame carefully by turning with a small screwdriver as shown below

on the screw in the middle of the gas cocks as well as nozzle changes

(gure 6 and 7).

Figure 6

Figure 7

DESCRIPTION OF OVEN

Tumspit Fan

Top + Bottom heating element

Lamp

Bottom heating element + Fan

Grill heating element

Grill heating element+Lamp

Electrical timer

Turbo heating + Fan

Bottom + Top heating elements + Fan

Grill heating element+Fan

Grill burner / Grill heating element

Top heating element

Oven burner / Bottom heating element

Flame Ignition lighter

THERMOSTAT KNOB; In order to operate the oven, thermostat must beadjusted to desired temperature. Your thermostat has a feature of adjustment to 50 - 280 degree.

MECHANIC TIMER KNOB (Optional); In order to operate the oven, timerswitch should be adjusted to desired time from 0-90 minute. You can use cooking time table.

Front right

burner (small

burner)

Grill

burner

or heating

element

Rear right

burner

(middle

burner)

Oven burner (optional) or

heating

element

Wok burner

or hotplate

Timer

(optional)

Front

electric

hot plate

Thermostat

(optional)

Rear

electric

hot plate

Turnspit Lamp

Rear left

burner

(middle

burner)

Front left

burner (big

burner)

Ignition

lighter

DESCRIPTION OF THE CONTROL PANELS

USING THE BURNER GROUPS

1. Closed Fully open Half open

2. Our gas ovens top and bottom burner working system is one by one.

When you want use your preference burner, before you must make press

the tap knob and wait nearly 5-10 second. Then you can to iname

through with automatic ignition system (optional) or match. You must

wait 10-15 second after iname to have press by tap knob and after you

can make allow the knob. If you can not made this operation you must try again.

3. The cocks controlling the gas cookers have special mechanism. In

order to light the cooker;

4. Always press on the switch forward and bring it to ame symbol by

turning anticlockwise (left). All of the lighters shall operate and the cooker you controlled shall light only. Keep the switch pressed until ignition is performed. (OPTIONAL)

5. If your oven has ignition system from push button switch please press

and turn gas valve open position and same time press ignition button.

6. In models with security system, when ame of the cooker is extin-

guished, control valve cuts off the gas automatically. For operate the burners with gas security system you must make press the knob and turn antilock wise. After the ignition (with optional automatic ignition system or match) you must wait nearly 5-10 second for gas security systems activation.

7. Do not continuously operate the igniter for more than 15 seconds. After

15 seconds, if the burner does not ignite, then stop and if you are trying to ignite the oven then open the door and wait a minimum of one minute before trying again. If the burner is extinguished for of the any reason, close the gas control valve and wait a minimum of one minute before trying again.

8. Before operating your hob please make sure that the burner caps are

+ 34 hidden pages