USER Manual
Valens 500 / Valens 500M
Valens 600 / Valens 500M
Valens 700 / Valens 700M
All rights reserved by Rosewill
POWER SUPPLY
1
Contents
5> Connectors
P. 4
6> Installation
P. 5
8> Safety and Warning
P. 6
9> Troubleshooting
P. 6
P. 6
7> Safety and EMI Certification
4> Specifications
P. 3
3> Package contents
P. 2
1> Introduction P. 2
2> Product Features
P. 2
All rights reserved by Rosewill
POWER SUPPLY
2
Product Features
• 80 Plus Gold certified to deliver over 90% efficiency
• ATX 12V V2.3 ready, supports to EPS 12V 2.92 and backwards compatible
with ATX 12V 2.01
• Cable management modular (modular models)
• Active Power Factor Correction (PFC) with PF value of 0.99
• Maximum Protection: Over-voltage and over-current protection,
short circuit protection, under-voltage protection, over power protection
• Long lasting, Ultra-quiet 120mm hydraulic fan
• Extra-long cables support full size gaming chassis
• Crossfire and SLI support
• MTBF >100,000 hours at 80% load, ambient temperature at 25℃
Package Contents
Introduction
Rosewill is the platform of choice for avid PC gamers and the Rosewill Valens
Power Supply series is built to the highest quality standard and delivers the
ultimate performance for enthusiasts.
• Valens Power Supply Unit x1
• User manual x1
• AC power cord x1
• Cable tie x1
• Mounting screws x4
• Valens Modular Power Supply Unit x1
• Modular cable set x1
• User manual x1
• AC power cord x1
• Cable tie x1
• Mounting screws x4
Valens 500/600/700 Valens 500M/600M/700M
All rights reserved by Rosewill
POWER SUPPLY
3
Electronic Specifications
Model No. :Valens 500/Valens 500M
Model No.
Valens 500
Valens 500M
100V-240V 10A-5A
AC Input
DC Output +3.3V
20A
100W 498W
500W
20A 41.5A 0.5A
6W 12.5W
2.5A
+5V +12V -12V +5V
SB
Max Output
Current
Max Combined
Wattage
Total Output
Voltage Current
Model No. : Valens 600/Valens 600M
Model No.
Valens 600
Valens 600M
100V-240V 10A-5A
AC Input
DC Output +3.3V
20A
100W 600W
600W
20A 50A 0.5A
6W 12.5W
2.5A
+5V +12V -12V +5V
SB
Max Output
Current
Max Combined
Wattage
Total Output
Voltage Current
Model No. : Valens 700/Valens 700M
Model No.
Valens 700
Valens 700M
100V-240V 10A-5A
AC Input
DC Output +3.3V
20A
100W 696W
700W
20A 58A 0.5A
6W 12.5W
2.5A
+5V +12V -12V +5V
SB
Max Output
Current
Max Combined
Wattage
Total Output
Voltage Current
All rights reserved by Rosewill
POWER SUPPLY
4
20+4
MainBoard
PIN
Cable
Valens 500
Valens 600
Valens 700
+12V EPS
4+4 PIN
Connector
6+2 PIN
PCI-E
Connector
SATA
Connector
4 PIN Molex
Peripheral
Connector
4 PIN
Floppy
Connector
Connectors
1
1
1
1
1
1
2
2
4
1
1
1
5
6
6
4
4
4
Valens 500/600/700
20+4
MainBoard
PIN
Cable
Valens
600M
Valens
700M
+12V EPS
4+4 PIN
Connector
6+2 PIN
PCI-E
Connector
SATA
Connector
4 PIN Molex
Peripheral
Connector
4 PIN
Floppy
Connector
1
1
1
1
1
1
x2 fixed
2
2
2
1
1
1
5
6
6
4
4
4
Valens 500M/600M/700M
ModularFixed
Valens
500M
All rights reserved by Rosewill
POWER SUPPLY
5
If replacing an existing PSU in a system, you will first need to remove the old PSU.
Please proceed as follows:
1. Disconnect the AC power cord from your existing power supply unit
2. Disconnect the power supply from all the components in the PC, make sure that
all the connectors are unplugged.
3. Remove the four screws from the rear of the case that hold the old power supply to
the chassis, and then remove the old power supply unit form case.
Installation
Installing the new Valens series power supply:
1. Make sure the I/0 switch of the PSU is at off “O” position.
2. Install the Power supply unit in the appropriated space in the PC case and secure it
by screwing the four screws into the rear of the power supply.
3. Connect the 20+4 pin main power cable to the motherboard 20/24pin socket.
The detachable 4 pin section of the connector can be separated to support a 20 pin
connection or section together to support a 24 pin socket.
4. Connect the 4+4 PIN (8 PIN) power cable to the mainboard. If your mainboard supports
only 4 PIN jack, connect only the right side of the connector to the mainboard.
5.If your are using a graphics board with a 6 PIN/8 PIN connector please connect the
respective connector to the socket on the board.
If your graphics supports more than one socket, please connect the respective
connector to the socket on board.
6. Connect the SATA or Peripheral 4 PIN Molex connectors to the hard disk or SSDs or
optical drive.
7.
Connect any others internal components that require power to the appropriate connector.
8. Make sure all the cables are securely seated
9. Connect the AC power cord into the back of the power supply and Switch on
I/O switch at input “I” position.
10. Your PSU is now connected and ready.
Pin1
COM
COM
COM
COM
COM
COM
+12V DC
+12V DC
+12V DC
+12V DC
+12V DC
+12V DC
Pin3
Pin1 Pin5
Pin4 Pin5
Pin2 Pin4
+12V CPU power connector
(EPS 8Pin/4+4Pin)
Right
All rights reserved by Rosewill
POWER SUPPLY
6
Safety and EMI Certification
Safety & Warning
Troubleshooting
• Due to the high voltage inside the power supply, do not attempt to remove the cover
of power supply. The warranty will be void if the cover is removed.
• Do not insert any objects into the open ventilation or fan grill area of the power supply.
• Do not store the power supply in high humidity and high temperature environment,
• Do not plug or unplug the power cord with wet hand.
If you installed the new power supply and the system is not working properly,
please check the following:
• Make sure the AC power cord is plugged correctly into PSU inlet socket and
power switch is at input “I” position.
• Make sure the wall socket, extension power cord, power strip or surge protector in use,
fully functional and wall power switch turned on
• Make sure that all the connectors from power supply are correctly plugged
into the mainboard.
• Make sure there are no short circuits within the systems that could result from
defective hardware or misplaced connectors
• If your are not sure take all parts out of the housing and only leave the mainboard
inside together with the power supply. Disconnect all plugs, check them and then
connect them again to the respective sockets.
Information
Thank you for purchasing a High-Quality Rosewill Product.
Please register your product at : www.rosewill.com for complete warranty information and
future support for your product.If you have any question while using our products,
please feel free to contact us at techsupport@rosewill.com
Support Phone Number: 800-575-9885
Support Email: techsupport@rosewill.com
RoHS
Compliant
E 307777E 307777
USER Manual
Valens 500 / Valens 500M
Valens 600 / Valens 500M
Valens 700 / Valens 700M
www.rosewill.com
Loading...