Rosewill RNX-N360PC User Manual

Wireless N PCI Adapter RNX-N360PC

User Manual

1910020413

FCC STATEMENT

This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to pro-vide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not in-stalled
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:

z Reorient or relocate the receiving antenna.

z Increase the separation between the equipment and receiver.

z Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

z Consult the dealer or an experienced radio/ TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions:

1). This device may not cause harmful interference.

2). This device must accept any interference received, including interference that
may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.

FCC RF Radiation Exposure Statement

This equipment complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment. This device and its antenna must not be co-located or
operating in conjunction with any other antenna or transmitter.

“To comply with FCC RF exposure compliance requirements, this grant is applicable to
only Mobile Configurations. The antennas used for this transmitter must be installed to
provide a separation distance of at least 20 cm from all persons and must not be
co-located or operating in conjunction with any other antenna or transmitter.”

CE Mark Warning

This is a class B product. In a domestic environment, this product may cause radio
interference, in which case the user may be required to take adequate measures.

National Restrictions

2400.0-2483.5 MHz

Country Restriction Reason/remark

Bulgaria General authorization required for outdoor

use and public service

France Outdoor use limited to 10

mW EIRP. within the band
2454-2483.5 MHz

Italy If used outside of own premises, general

Luxembourg General authorization required for network

Norway Implemented

Russian
Federation

Note: Please don’t use the product outdoors in France

Only for indoor applications

Military Radiolocation use. Refarming of the

2.4 GHz band has been ongoing in recent
years to allow current relaxed regulation. Full
implementation planned 2012

authorization is required

and service supply(not for spectrum)

This subsection does not apply for the
geographical area within a radius of 20 km
from the centre of Ny-Ålesund

Table of Content

Package Contents..........................................................................................1

Chapter 1 Overview ......................................................................................2

1.1 Overview of the product...................................................................2

1.2 Features...........................................................................................2

1.3 LED Status.......................................................................................3

Chapter 2 Installation Guide ........................................................................4

2.1 Hardware Installation .......................................................................4

2.2 Software Installation.........................................................................4

2.2.1 Ov

2.2.2 Software Installation for Windows XP

2.2.3 Software Installation for Windows Vista

2.2.4 Software Installation for Windows 7

erview .............................................................................................. 4

................................................... 4

................................................ 9

.................................................... 12

Chapter 3 Configuration Guide .................................................................16

3.1 Current Status................................................................................16

3.2 Profile Management.......................................................................17

3.2.1 Add or Modify

3.2.2 Remove a profile

3.2.3 Switch a profile

3.2.4 Ex

3.2.5 Import a Prof

3.2.6 Scan Av

3.2.7 Auto Profile

port a profile ................................................................................... 23

a Configuration Profile ................................................. 18

................................................................................ 22

................................................................................... 22

ile ................................................................................... 23

ailable Networks.................................................................... 24

Selection Management ................................................... 24

3.3 Diagnostics ....................................................................................25

3.3.1 Check Driv

3.3.2 Check Receive and Transmit Statistica

er Information.................................................................... 26

l Information .......................... 26

3.4 Configuration for Windows Vista....................................................27

3.5 Configuration for Windows 7..........................................................29

Chapter 4 WPS Configuration ...................................................................32

4.1 PBC (Push Button Configuration) method .....................................32

4.2 PIN method....................................................................................34

4.2.1 Enter a PIN i

4.2.2 Enter the PI

nto your AP device ......................................................... 34

N from your AP device..................................................... 36

Appendix A: Specifications.........................................................................37

Appendix B: Glossary .................................................................................38

Appendix C: FAQ .........................................................................................40

Package Contents

The following items should be found in your package:

¾ One RNX-N360PC Wireless N PCI Adapter

¾ Quick Installation Guide

¾ One Resource CD for RNX-N360PC, including:

• Wireless N Client Utility and Drivers

• User Guide

• Other Helpful Information

Note:

)

Make sure that the package contains the above items. If any of the listed items are
damaged or missing, please contact with your distributor.

Conventions:

The ‘Adapter’ mentioned in this user guide stands for RNX-N360PC Wireless N PCI
Adapter without any explanations.

1

Chapter 1 Overview

Thank you for choosing RNX-N360PC Wireless N PCI Adapter.

1.1 Overview of the product

The adapter is an 802.11n client device; it is designed to provide a high-speed and
unrivaled wireless performance for your notebook. With a faster wireless connection, you
can get a better Internet experience, such as downloading, gaming, video streaming and
so on.

With the 802.11n technology, higher throughput improvements using MIMO (multiple input,
multiple output antennas), the RNX-N360PC’s auto-sensing capability allows high packet
transfer rate of up to 300Mbps for maximum throughput. It has good capability on
anti-jamming, and it can also interoperate with other wireless (802.11b) products. The
adapter supports WEP, WPA and WPA2 encryption to prevent outside intrusion and
protect your personal information from being exposed.

The adapter is easy to install and manage. The Quick Setup Wizard guides you
step-by-step through the installation process; the Wireless N Client Utility helps you create
a wireless connection immediately.

With unmatched wireless performance, reception, and security protection, the
RNX-N360PC is the best choice for easily adding or upgrading wireless connectivity to
your notebook computer.

1.2 Features

¾ Complies with IEEE802.11n, IEEE802.11g, IEEE802.11b standards

¾ Supports WPA/WPA2 data security, IEEE802.1x authentication, TKIP/AES encryption,

64/128/152-bit WEP encryption

¾ Supports high rate of up to 300Mbps for maximum throughput, supports automatically

adjust to lower speeds due to distance or other operating limitations

2

¾ Provides 32-bit PCI interface

¾ Supports Ad-Hoc and Infrastructure modes

¾ Good capability on anti-jamming

¾ Supports roaming between access points when configured in Infrastructure mode

¾ Ease to configure and provides monitoring information

¾ Supports Windows 2000/ XP/ Vista/ 7

¾ Three External antennas which are listed in a format of 3x3 for three receivers and

three transmitters.

1.3 LED Status

LED Indications Status Working Status

Status Solid Light

Flashing Slowly

Activity

Flashing Quickly The adapter is transmitting or receiving data.

The adapter is inserted in the slot and the power
is on.

The adapter is trying to scan a networking
connection;

The adapter is already connected but is not
transmitting or receiving data.

3

Chapter 2 Installation Guide

2.1 Hardware Installation

To install the adapter, follow these steps listed below:

1. Turn off your desktop PC and disconnect the power.

2. Remove your PC case and locate an available PCI slot on the motherboard. Remove
the metal slot cover on the back of the PC. Check with your computer manufacturer for
instructions if needed.

3. Slide the PCI Adapter into the PCI slot. Make sure that all of its pins are touching the
slot's contacts. Once the adapter is firmly in place, secure its fastening tab to your PC's
chassis with a mounting screw. Then, close your PC case.

4. Reconnect your PC’s power and turn on your desktop PC.

2.2 Software Installation

2.2.1 Overview

The Adapter’s Setup Wizard will guide you through the Installation procedure for Windows
2000/ XP/ Vista/ 7. The Setup Wizard will install the Wireless N Client Utility and drivers.

When you install the hardware prior to before installing the software, the system will
prompt “Found New Hardware Wizard”, click Cancel, and run the Setup Wizard program
on the CD-ROM.

The Setup steps for Windows 2000/ XP/ Vista/ 7 are very similar. The following setup
steps are for Windows XP and for Windows Vista.

2.2.2 Software Installation for Windows XP

1. Insert the Resource CD into your CD-ROM drive, and open the folder named
RNX-N360PC. Double-click Setup.exe in the proper folder to start the installation,
and then the following screen for preparing setup will appear.

4

Figure 2-1

2. Soon, Figure 2-2 will display after a moment. Click Next to continue.

Figure 2-2

3. After that, you should choose a Setup type. It is recommended that you select Install
Client Utilities and Driver. Select Install Driver Only to install driver only (shown in
Figure 2-3). Click Next to continue.

5

Figure 2-3

4. Click Browse to change the destination location for the software, then click Next in
the screen below (shown in Figure 2-4).

Figure 2-4

5. After that, select the program folder, you should create a new folder name or select
one from the Existing Folders list. It is recommended that you keep the default
setting. Click Next to continue the installation.

6

Figure 2-5

6. Choose configuration tool, if you are not sure, please leave it default. Then click Next
to continue.

Figure 2-6

7. Wait a while for the setup as shown in Figure 2-7.

7

Figure 2-7

Note:

)

1) For Windows XP, the Setup Wizard will notify you of how to proceed with the

installation duringthese steps (shown inFigure 2-8). Our drivers have be
thoroughly, and are able to work with the operating system. Click Continue
Anyway to continue the Installation.

en tested

Figure 2-8

2) In Windows 2000, the warning screen is shown below (Figure 2-9), and please

8

select Yes to continue installation.

Figure 2-9

8. After all the steps above, you will see the screen below, click Finish to complete the
installation.

Figure 2-10

2.2.3 Software Installation for Windows Vista

1. Insert the Resource CD into your CD-ROM drive, and open the folder named

RNX-N360PC. Double-click Setup.exe in the proper folder to start the installation,

9

then the following screen for preparing setup will appear.

Figure 2-11

2. Soon, Figure 2-12 will display after a moment. Click Next to continue.

3. Click Yes to continue.

Figure 2-12

10

Figure 2-13

4. The following page will display and please wait a moment.

Figure 2-14

Note:

)

For Windows Vista, the Setup Wizard will notify you of how to proceed with the installation
during these steps (shown in Figure 2-15). Ou
are able to work with the operating system. Click Install this driver software anyway to
continue the Installation.

r drivers have been tested thoroughly, and

11

Figure 2-15

5. Click Finish to complete the installation.

Figure 2-16

2.2.4 Software Installation for Windows 7

1. Insert the Resource CD into your CD-ROM drive. To continue, find the CD/DVD drive
where the installation CD was placed. Open RNX-N360PC folder, and double-click
Setup.exe. Then you will see Figure 2-17.

12

Figure 2-17

2. Soon, Figure 2-18 will display after a moment. Click Next to co

Figure 2-18

ntinue.

3. Wait a while for the setup as shown in Figure 2-19.

13

Figure 2-19

Note:

)

For Windows 7, the Setup Wizard will notify you about the Windows Security with the
installation during these steps (shown in Figure 2-20). Our drivers have been tested
thoroughly, and are able to work with the operating system. Click Install this driver
software anyway to continue the installation.

Figure 2-20

4. Then you will see Figure 2-21. Click Fin

ish to complete.

14

Figure 2-21

15

Chapter 3 Configuration Guide

RNX-N360PC can be configured by Wireless N Client Utility. This chapter describes how
to configure your Adapter for wireless connectivity on your Wireless Local Area Network
(WLAN) and use the data security encryption features.

After Installing the Adapter, the Adapter’s tray icon

appears at the bottom of the screen, and shows the signal strength using color and the
received signal strength indication (RSSI).

If the icon is gray, there is no connection.

If the icon is red, there is poor signal strength and the RSSI is less than 5dB.

If the icon is yellow, there is poor signal strength and the RSSI is between 5dB and

10dB.

If the icon is green, there is good signal strength and the RSSI is between 10dB and

20dB.

If the icon is green, there is excellent signal strength and the RSSI is more than 20dB.

Double-click the icon and the Wireless N Client Utility will run. You can also run the utility
by clicking the Start → All programs → rosewill → Wireless N Client Utility →
Wireless Client Utility. The Wireless N Client Utility provides some integrated and easy
tools to:

¾ Display current status information

will appear in your system tray. It

¾ Edit and add configuration profiles
¾ Display current diagnostics information

The section below introduces these above capabilities.

3.1 Current Status

The Current Status tab contains general information about the program and its operations.
The Current Status tab needn’t any configurations.

16

Figure 3-1

The following table describes the items found on the Current Status screen.

¾ Profile Name - This shows the name of current selected configuration profile. The

configuration of Profile name will be described on the General tab of Profile
Management.

¾ Link Status - This shows whether the station is associated to the wireless network.

¾ Wireless Mode - Here displays the wireless mode.

¾ Network Type - The type of network and the station currently connected are shown

here. The options include:

• Infrastructure (Access Point)

• Ad Hoc

Note:

)

You can configure the network type and wireless mode on the

Management

¾ IP Address - This displays the computer’s IP address.

¾ Control Channel - This shows the currently connected channel.

.

Advanced

tab of

Profile

¾ Data Encryption - Here displays the encryption type the driver is using. You can

configure it on the Security tab of Profile Management.

¾ Server Based Authentication - This shows whether the server based authentication

is used.

¾ Signal Strength - This shows the strength of the signal.

Click Advanced on the screen above, you can see advanced information about the
program and its operations.

3.2 Profile Management

Click the Profile Management tab of the Wireless N Client Utility and the next screen will
appear (shown in Figure 3-2). The Profile Management screen provides tools to:

17

¾ Add a new profile

¾ Modify a Profile

¾ Remove a Profile

¾ Activate a Profile

¾ Import a Profile

¾ Export a Profile

¾ Scan Available Networks

¾ Order profiles

Figure 3-2

3.2.1 Add or Modify a Configuration Profile

To add a new configuration profile, click New on the Profile Management tab. To modify a
configuration profile, select the configuration profile from the Profile list and click Modify.
Then you will see the Management dialog box (shown in Figure 3-3).

Edit the General tab

1.

¾ Profile Name - Please enter the Profile name which identifies the configuration

profile. This name must be unique. Note that the profile names are not case-sensitive.

¾ Client Name - Please enter the Profile name which identifies the client machine.

¾ Network Names (SSIDs) - Please enter the IEEE 802.11 wireless network name.

This field has a maximum limit of 32 characters.

18

Figure 3-3

2. Edit the Security tab

Select the Security tab in the screen above, and then you can edit the fields to configure
the profile. To define the security mode, select the radio button of the desired security
mode as follows.

Figure 3-4

¾ WPA/WPA2: Wi-Fi Protected Access

¾ WPA/WPA2 Passphrase: Wi-Fi Protected Access Passphrase

¾ 802.1x: Enables 802.1x security.

¾ Pre-Shared Key (Static WEP): Enables the use of shared keys that are defined on

19

both the access point and the station. To define shared encryption keys, choose the
Shared Key radio button and click Configure to fill in the Define Shared Keys window
(shown in Figure 3-5).

Note:

)

The

¾ None: No security (not recommended).

)

If the access point which the Adapter is associated has WEP set and the client has WEP
enabled, make sure that Allow Association to Mixed Cells is checked on the Security
tab to allow

802.11 Authentication Mode as appropriate on the Advanced tab of this Profile

Management dialog.

To configure the Encryption Keys under the Pre-Shared keys (Static WEP) Security mode:

security mode is not available for 802.11n.

WEP

Note:

association. To complete WEP encryption configuration, you must select the

Figure 3-5

Note:

)

Select different Security Options, the configurations are different; you can select the
appropriate security option and configure the exact key as your need.

3. Edit the Advanced tab

This screen below allows you to make advanced configuration for the profile.

20

Figure 3-6

¾ Power Save Mode - Please select the power save mode in the drop-down list.

• Maximum-Selects maximum mode to let the access point buffer incoming

messages for the Adapter. The Adapter will detect the access point if any
messages are waiting periodically.

• Normal -Normal mode uses maximum when retrieving a large number of

packets, then switches back to power save mode after retrieving the packets.

• Off - Turns power saving off, thus powering up the Wireless PCI Adapter

continuously for a short message response time.

¾ Network Type: There are basically two modes of networking:

• Infrastructure- All wireless clients will connect to an access point or wireless

router.

• Ad-Hoc- Directly connecting to another computer, for peer-to-peer

communication, using wireless network adapters on each computer, such as two
or more RNX-N360PC wireless adapters.

Note:

)

1) An Infrastructure network contains an Access Point or wireless router. All the wireless
devices or clients will connect to the wireless router or access point.

2) An Ad-Hoc network contains only clients, such as laptops with wireless desktop

adapters. All the adapters must be in Ad-Hoc mode to communicate.

¾ Wireless Mode: Specifies 2.4 GHz 300 Mbps, 2.4 GHz 54 Mbps or 2.4 GHz 11 Mbps

operation in an access point network. The Wireless adapter must match the wireless
mode of the access point with which it associates.

¾ Wireless Mode when Starting Ad Hoc Network: S

to start an Ad Hoc network if no matching network name is found after scanning all
available modes. This mode also allows the selection of the channel that the Wireless

21

pecifies 2.4 GHz 300/54/11 Mbps

Adapter uses. The channels available depend on the regulatory domain. If the
adapter finds no other ad hoc adapters, the channel that the adapter starts the ad hoc
network with will be selected automatically. The Adapter must match the wireless
mode and channel of the clients it associates.

¾ 802.11 Authentication Mode: Select which mode the Adapter uses to authenticate

to an access point:

• Auto causes the adapter to attempt authentication using shared, but switches it

to open authentication if shared fails.

• Open enables an adapter to attempt authentication regardless of its WEP

settings. It will only associate with the access point if the WEP keys on both the
adapter and the access point match.

• Shared only allows the adapter to associate with access points that have the

same WEP key.

For infrastructure (Access Point) networks, click Preferred APs… to specify four access
points at most to the client adapter that attempts to be associated to the access points.
The four access points have different priorities; the frontal has the higher priority.

Figure 3-7

3.2.2 Remove a profile

1. Go to the Profile Management tab (shown in Figure 3-2).

2. Select the profile name in the Profiles List.

3. Click Remove.

Note:

)

The profile being used can’t be removed.

3.2.3 Switch a profile

1. Go to the Profile Management screen (shown in Figure 3-2).

2. Select the profile name required in the Profiles List.

3. Click Activate.

22

3.2.4 Export a profile

1. From the Profile Management screen (shown in Figure 3-2), highlight the profile to

export.

2. Click Export…, the Export Profile window will then appear below.

3. Browse the directory to export the profile to.

4. Click Save. The profile should then be exported to the specified location.

Figure 3-8

3.2.5 Import a Profile

1. From the Profile Management screen (shown in Figure 3-2), click Import…. Then the
Import Profile will appear below.

2. Browse to the directory where the profile is located.

3. Highlight the profile name.

4. Click Open, the imported profile will then appear in the Profiles List.

23

Figure 3-9

3.2.6 Scan Available Networks

1. Click Scan on the Profile Management screen (shown in Figure 3-2), the Available
Infrastructure and Ad Hoc Networks window will appear below.

2. Click Refresh to refresh the list at any time.

3. Highlight a network name and click Activate to connect to an available network. If no
configuration profile exists for that network, the Profile Management window will open
the General tab screen. Fill in the Profile name and click OK to create the
configuration profile for that network.

Figure 3-10

3.2.7 Auto Profile Selection Management

The auto selection feature allows the adapter to automatically select a profile from the list
of profiles and use it to connect to the network. To add a new profile into the Auto Selected
Profiles list, please follow these steps.

1. On the Profile Management screen (shown in Figure 3-2), click Order Profiles….

2.

The Auto Profiles Selection management window will appear (shown in Figure 3-11)
with a list of

all created profiles in the Available Profiles.

24

Figure 3-11

3. Highlight the profiles to add to auto profile selection, and click Add. The profile will
appear in the Auto Selected Profiles box.

4. Highlight a profile in the Auto Selected Profiles box.

5. Click Move Up or Move Down as appropriate.

Note:

)

The first profile in the Auto Selected Profiles box has highest priority, while the last profile
has the lowest priority.

6. Click OK.

7. Check the Auto Select Profiles checkbox on the Profile Management tab (shown in
Figure 3-2).

Note:

)

When auto profile selection is enabled by checking Auto Select Profiles on the Profile
Management tab, the client adapter will scan for an available network. The profile with the

highest priority and the same SSID as one of the found networks will be used to connect
to the network. If the connection fails, the client adapter will try the next highest priority
profile that matches the SSID until an available network is found.

3.3 Diagnostics

The Diagnostics tab of the Wireless N Client Utility provides buttons used to retrieve
receiving and transmitting statistics. The Diagnostics tab does not require any
configuration.

The Diagnostics tab lists the following receiving and transmitting diagnostics for frames
received or transmitted by the wireless network adapter:

¾ Multicast frames transmitted and received

25

¾ Broadcast frames transmitted and received

¾ Unicast frames transmitted and received

¾ Total bytes transmitted and received

Figure 3-12

3.3.1 Check Driver Information

Click the Adapter Information button in the screen above, you will see the adapter
information, including general information about the wireless network adapter and the
Network Driver Interface Specification (NDIS) driver. Access the adapter information from
the Diagnostics tab.

¾ Card Name - The name of the wireless network adapter.

¾ MAC Address - The MAC address of the wireless network adapter.

¾ Driver - The driver name and path of the wireless network adapter driver.

¾ Driver Version - The version of the wireless network adapter driver.

¾ Driver Date - The creation date of the wireless network adapter driver.

¾ Client Name - The name of the client computer.

3.3.2 Check Receive and Transmit Statistical Information

The Advanced Statistics show receiving and transmitting statistical information about the
following receiving and transmitting diagnostics for frames received by or transmitted to
the wireless network adapter.

26

Figure 3-13

3.4 Configuration for Windows Vista

After the Adapter's driver has been installed, Windows Vista will display a wireless
Network Connection message like this one.

Figure 3-14

To establish a connection, please follow the steps below.

1. Right-click the icon

2. The following screen will show you available wireless networks. Highlight the one you
want to join, and then click Connect.

in your system tray, then click Connect to a network.

Figure 3-15

27

Figure 3-16

3. To continue, click Connect Anyway. Click the Cancel button to end the connection.

Figure 3-17

4. If the connection is successfully established, the following screen will appear, click
Close to finish the connection.

28

Figure 3-18

3.5 Configuration for Windows 7

Wireless N Client Utility is not available for Windows 7. So after the Adapter's driver has
been installed, we have to use Windows WLAN Autoconfig to establish a connection.
Please follow the steps below.

29

1. Right-click the icon at the bottom of your screen in your system tray and then
you will see the available wireless network list. Select the SSID of your Access Point,
take rosewill for example. Click Connect.

Figure 3-19

2. If your wireless network is secured, you will be required to enter the security key as
shown in Figure 3-20. Enter the passphrase, take 12345

67890 for example. And then

click OK.

Figure 3-20

30

3. If the key entered is correct, you will successfully connect to the network as shown in
Figure 3-21.

Figure 3-21

31

Chapter 4 WPS Configuration

WPS (Wi-Fi Protected Setup) function allows you to add a new wireless device to an
existing network quickly.

If the wireless card supports WPS, you can establish a wireless connection between
wireless card and router using either Push Button Configuration (PBC) method or PIN
method.

First, the WPS software should be installed. Insert the Resource CD into your CD-ROM
drive, and open the folder named RNX-N360PC. Double-click WPS.exe in the proper
folder to start the installation, then the following screen for preparing setup will appear.

Figure 4-1

Then, please follow the clue of the Operation System to complete the WPS installation.
After that, WPS function can be enabled. Here we will introduce two ways to configure the
WPS (For the configuration of WPS, here takes the Wireless Router of our company for
example).

4.1 PBC (Push Button Configuration) method

1. Firstly, press the WPS button directly on the front panel of the Router shown in Figure

4-2.

Figure 4-2

2. Double click the icon

the welcome screen shown as Figure 4-3. Click Next to continue. Then select Push

on the desktop to open the WPS Utility and then you can see

32

the button on my access point in the next screen shown in Figure 4-4 and click
Next.

Figure 4-3

Figure 4-4

3. Then wait a minute until Figure 4-5 appears. Click Fin

configuration.

33

ish to complete the WPS

Figure 4-5

4.2 PIN method

There are two ways to configure the WPS by PIN method:

1) Enter a PIN into your AP device.

2) Enter the PIN from your AP device.

Following are the detailed configuration procedure of each way.

4.2.1 Enter a PIN into your AP device

1. Double click the icon on the desktop to open the WPS Utility and then you can

see the welcome screen shown as Figure 4-3. Click Next to continue. Figure 4-4 will
appear
is randomly generated. Click Next.

. Select the second option and you will see the PIN value of the adapter which

34

Figure 4-6

2. Open the Router’s Web-based Utility and click WPS link on the left of the main menu.

Then Figure 4-7 will appear.

Figure 4-7

3. Click Add device, then you can see Figure 4-8. Select Enter the ne

and enter the PIN value of the adapter shown in Figure 4-6, click Connect.

Figure 4-8

4. When Figure 4-5 appears, the WPS configuration is complete.

35

w device’s PIN

4.2.2 Enter the PIN from your AP device

1. Open the WPS Utility and you will see Figure 4-3. Click Next to continue. Then Figure

4-4 will appear. Select the third option and enter the PIN value which is labeled on the
bottom of the Router. Click Next.

Figure 4-9

2. When Figure 4-5 appears, the WPS configuration is complete.

Note:

)

If you generate a new PIN code for your Router, please enter the new one instead.

36

Appendix A: Specifications

Normal

Interface 32 bit PCI Interface

Standards IEEE802.11n; IEEE802.11g; IEEE802.11b;

Operating System Windows 2000/Windows XP/Windows Vista/Windows 7

Up to 300Mbps

13.5/27/40.5/54/81/108/121.5/135Mbps
13/26/39/52/78/104/117/130Mbps

Radio Data Rate

6.5/13/19.5/26/39/52/58.5/65Mbps
1/2/5.5/11Mbps

(Auto Rate Sensing)

11b:CCK,QPSK,BPSK;

Modulation

Media Access Protocol CSMA/CA with ACK

Data Security WPA/WPA2; 64/128/152-bit WEP; TKIP/AES

Frequency

Spread Spectrum Direct Sequence Spread Spectrum (DSSS)

Safety & Emissions FCC, CE

11g:OFDM;

11n: QPSK,BPSK,16-QAM,64-QAM;

2.412 ~ 2.462GHz

(Only 2.412GHz~2.462GHz is allowed to be used in the USA,
which means only channel 1~11 is available for American users
to choose)

Environmental and Physical

Operating Temp.

Storage Temp.

0℃~40℃ (32℉~104℉)

-40℃– 70℃ (-40℉~158℉)

Working Humidity 10% - 90% RH, Non-condensing

Storage Humidity 5% - 90% RH, Non-condensing

37

Appendix B: Glossary

¾ 802.11b - The 802.11b standard specifies a wireless product networking at 11 Mbps

using direct-sequence spread-spectrum (DSSS) technology and operating in the
unlicensed radio spectrum at 2.4GHz, and WEP encryption for security. 802.11b
networks are also referred to as Wi-Fi networks.

¾ 802.11g - specification for wireless networking at 54 Mbps using direct-sequence

spread-spectrum (DSSS) technology, using OFDM modulation and operating in the
unlicensed radio spectrum at 2.4GHz, and backward compatibility with IEEE 802.11b
devices, and WEP encryption for security.

¾ Ad-hoc Network - An ad-hoc network is a group of computers, each with a Wireless

Adapter, connected as an independent 802.11 wireless LAN. Ad-hoc wireless
computers operate on a peer-to-peer basis, communicating directly with each other
without the use of an access point. Ad-hoc mode is also referred to as an
Independent Basic Service Set (IBSS) or as peer-to-peer mode, and is useful at a
departmental scale or SOHO operation.

¾ DSSS - (Direct-Sequence Spread Spectrum) - DSSS generates a redundant bit

pattern for all data transmitted. This bit pattern is called a chip (or chipping code).
Even if one or more bits in the chip are damaged during transmission, statistical
techniques embedded in the receiver can recover the original data without the need
of retransmission. To an unintended receiver, DSSS appears as low power wideband
noise and is rejected (ignored) by most narrowband receivers. However, to an
intended receiver (i.e. another wireless LAN endpoint), the DSSS signal is recognized
as the only valid signal, and interference is inherently rejected (ignored).

¾ FHSS - (Frequency Hopping Spread Spectrum) - FHSS continuously changes (hops)

the carrier frequency of a conventional carrier several times per second according to
a pseudo-random set of channels. Because a fixed frequency is not used, and only
the transmitter and receiver know the hop patterns, interception of FHSS is extremely
difficult.

¾ Infrastructure Network - An infrastructure network is a group of computers or other

devices, each with a Wireless Adapter, connected as an 802.11 wireless LAN. In
infrastructure mode, the wireless devices communicate with each other and to a
wired network by first going through an access point. An infrastructure wireless
network connected to a wired network is referred to as a Basic Service Set (BSS). A
set of two or more BSS in a single network is referred to as an Extended Service Set
(ESS). Infrastructure mode is useful at a corporation scale, or when it is necessary to
connect the

¾ Spread Spectrum - Spread Spectrum technology is a wideband radio frequency

technique developed by the military for use in reliable, secure, mission-critical
communications systems. It is designed to trade off bandwidth efficiency for reliability,
integrity, and security. In other words, more bandwidth is consumed than in the case
of narrowband transmission, but the trade off produces a signal that is, in effect,
louder and thus easier to detect, provided that the receiver knows the parameters of
the spread-spectrum signal being broadcast. If a receiver is not tuned to the right
frequency, a spread-spectrum signal looks like background noise. There are two
main alternatives, Direct Sequence Spread Spectrum (DSSS) and Frequency
Hopping Spread Spectrum (FHSS).

wired and wireless networks.

38

¾ SSID - A Service Set Identification is a thirty-two character (maximum) alphanumeric

key identifying a wireless local area network. For the wireless devices in a network to
communicate with each other, all devices must be configured with the same SSID.
This is typically the configuration parameter for a wireless PC card. It corresponds to
the ESSID in the wireless Access Point and to the wireless network name. See also
Wireless Network Name and ESSID.

¾ WEP - (Wired Equivalent Privacy) - A data privacy mechanism based on a 64-bit or

128-bit or 152-bit shared key algorithm, as described in the IEEE 802.11 standard. To
gain access to a WEP network, you must know the key. The key is a string of
characters that you create. When using WEP, you must determine the level of
encryption. The type of encryption determines the key length. 128-bit encryption
requires a longer key than 64-bit encryption. Keys are defined by entering in a string
in HEX (hexadecimal - using characters 0-9, A-F) or ASCII (American Standard Code
for Information Interchange – alphanumeric characters) format. ASCII format is
provided so you can enter a string that is easier to remember. The ASCII string is
converted to HEX for use over the network. Four keys can be defined so that you can
change keys easily.

¾ Wi-Fi - A trade name for the 802.11b wireless networking standard, given by the

Wireless Ethernet Compatibility Alliance (WECA, see http://www.wi-fi.net), an
industry standards group promoting interoperability among 802.11b devices.

¾ WLAN - (Wireless Local Area Network) - A group of computers and associated

devices communicate with each other wirelessly, which network serving users are
limited in a local area.

¾ WPA - (Wi-Fi Protected Access) - A wireless security protocol uses TKIP (Temporal

Key Integrity Protocol) encryption, which can be used in conjunction with a RADIUS
server.

39

Appendix C: FAQ

This chapter provides solutions to problems that may occur during the installation and
operation of the Wireless Adapter. Read the descriptions below to solve your problems.

1. I cannot communicate with the other computers linked via Ethernet in the

Infrastructure configuration.

1. Make sure that the PC to which the Adapter is associated is powered on.

2. Make sure that your Adapter is configured on the same channel and with the

same security options as with the other computers in the Infrastructure
configuration.

2. What should I do when the computer with the Adapter installed is unable to

connect to the wireless network and/or the Internet?

1. Check that the LED indicators for the broadband modem are indicating normal
activity. If not, there may be a problem with the broadband connection.

2. Check that the LED indicators on the wireless router are functioning properly. If
not, check that the AC power and Ethernet cables are firmly connected.

3. Check that the IP address, subnet mask, gateway, and DNS settings are
correctly entered for the network.

4. In Infrastructure mode, make sure the same Service Set Identifier (SSID) is
specified on the settings for the wireless clients and access points.

5. In Ad-Hoc mode, both wireless clients will need to have the same SSID. Please
note that it might be necessary to set up one client to establish a BSS (Basic Service
Set) and wait briefly before setting up other clients. This prevents several clients from
trying to establish a BSS at the same time, which can result in multiple singular BSSs
being established, rather than a single BSS with multiple clients associated to it.

6. Check that the Network Connection for the wireless client is configured properly.

If Security is enabled, make sure that the correct encryption keys are entered on both
the Adapter and the access point.

3. I can’t find any wireless access point / wireless device in ‘Site Survey’ function.

1. Click ‘Rescan’ for few more times and see if you can find any wireless access

point or wireless device.

2. Please move closer to any known wireless access point.

3. ‘Ad hoc’ function must be enabled for the wireless device you wish to establish a

direct wireless link.

4. Please adjust the position of network card (you may have to move your computer

if you’re using a notebook computer) and click ‘Rescan’ button for few more times.
If you can find the wireless access point or wireless device you want to connect
by doing this, try to move closer to the place where the wireless access point or
wireless device is located.

4. I cannot establish connection with a certain wireless access point

1. Click ‘Add to Profile’ for few more times.

2. If the SSID of access point you wish to connect is hidden (nothing displayed in

40

3. ‘SSID’ field in ‘Site Survey’ function), you have to input correct SSID of the access

point you wish to connect. Please contact the owner of access point to ask for
correct SSID.

4. You have to input correct passphrase / security key to connect an access point

with encryption. Please contact the owner of access point to ask for correct
passphrase / security key.

5. The access point you wish to connect only allows network cards with specific

MAC address to establish connection. Please go to ‘Status’ menu and write the
value of ‘MAC Address’ down, then present this value to the owner of access
point so he / she can add the MAC address of your network card to his / her
access point’s list.

5. The network is slow / having problem when transferring large files

1. Move closer to the place where access point is located.

2. There could be too much people using the same radio channel. Ask the owner of

the access point to change the channel number.

Thank you for purchasing a quality Rosewill Product.

Please register your product at: www.rosewill.com for complete warranty information and
future support for your product.

41