PoE Injector RNWA-PoE-100
User Manual
PoE Injector RNWA-PoE-100 User Manual
FCC STATEMENT
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
Consult the dealer or an experienced radio/ TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions:
1) This device may not cause harmful interference.
2) This device must accept any interference received, including interference that
may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
CE Mark Warning
This is a class B product. In a domestic environment, this product may cause radio
interference, in which case the user may be required to take adequate measures.
1
PoE Injector RNWA-PoE-100 User Manual
Table of Content
CHAPTER 1 OVERVIEW ........................................................................................... 3
1.1 PACKAGE CONTENT………………………………………………………………….3
1.2 FEATURES…………………………………………………………………………. ...4
1.3 PRODUCT SPECIFICATION …………………………………………………………..4
CHAPTER 2 EXTERNAL COMPONENT………………………………………………..5
2.1 HARDWARE DIAGRAM………………………………………………………………..5
CHAPTER 3 CONNECTING THE POE INJECTOR……………………………………6
3.1 WIRED SETUP………………………………………………………………………..7
3.2 WIRELESS SETUP……………………………………………………………………8
2
PoE Injector RNWA-PoE-100 User Manual
Chapter 1
Chapter 1 Overview
Thank you for choosing the RNWA-PoE-100 PoE Injector. The Power over Ethernet
(PoE*) Injector is able to supply steady power to Powered Device (PD*) or PoE
Splitter over the Ethernet cable. The Ethernet equipment can work as a Power
Sourcing Equipment (PSE*) with the help of the RNWA-PoE-100 connection.
PoE technology allows the existing Ethernet infrastructure to transmit electrical power,
along with data, to remote IP endpoints over the Ethernet cables, which can greatly
save the cost of the external power cables. Your network can benefit from PoE
technology for it will ensure the normal working status of your network while keep the
existing Ethernet infrastructure secure.
*PoE: This technology describes a system to transmit electrical power, along with
data, to remote devices over standard twisted-pair cable in an Ethernet
network.
*PD: A device powered by a PSE and thus consumes energy. Examples include
powering IP telephones, wireless LAN access points, network cameras,
network hubs, embedded computers etc.
*PSE: A device (switch or hub for instance) that will provide power in a PoE setup.
1.1 Package Content
Before getting started, please verify that your package includes the following items:
Rosewill RNWA-PoE-100 PoE Injector
One Power Adapter
One Ethernet (CAT5 UTP) Cable
This User Guide
Note: Please make sure that the package contains the above items. If any of the
listed items are damaged or missing, please contact with your distributor.
3
PoE Injector RNWA-PoE-100 User Manual
Normal
Standards
IEEE 802.3, IEEE 802.3u, IEEE 802.3af
Ports
PoE Port
100BASE-TX / 10BASE-T dual purpose port
LAN Port
Cabling Type
RJ45 CAT 5 UTP cable
LED
PWR
Safety & Emissions
FCC, CE
Environmental and Physical
Operating Temp
0℃~40℃ (32℉~104℉)
Storage Temp
-40℃~70℃ (-40℉~158℉)
Operating Humidity
10%~90% RH, Non-condensing
Storage Humidity
5%~90% RH, Non-condensing
1.2 Features
Complies with IEEE 802.3, IEEE 802.3u, IEEE 802.3af standards
Compatible with PoE compliant PDs and PoE Splitters
Transmits electrical power along with data in one single cable
External 48V DC power supply
Supports Plug-and-Play for the devices, without any configuration
Extended Distance up to 100 meters for power and data
1.3 Product Specification
4
PoE Injector RNWA-PoE-100 User Manual
PWR: Power LED, a steady green light indicates that the PoE
system has detected the PD or PoE Splitter and the power
adapter is working properly.
LAN IN: Connect to a network device
(such as a Switch or Router) with CAT5
UTP cable.
DC 48V: Connect to the provided
power adapter which can supply
steady power of 48V DC.
POWER+DATA OUT: Connect to
the PD or PoE Splitter with a CAT5
UTP cable.
Chapter 2
Chapter 2 External Component
2.1 Hardware Diagram
5
PoE Injector RNWA-PoE-100 User Manual
Chapter 3
Chapter 3 Connecting the PoE Injector
You can use RNWA-PoE-100 PoE Injector with PD or PoE Splitter to expand your
network to where there are no power lines or outlets, where you wish to fix devices
such as APs, IP Cameras or IP Phones, etc.
The following steps will tell you how to connect the PoE Injector correctly.
1. Use a CAT5 UTP cable to connect port of Ethernet device (such as a switch,
hub or router) to the LAN IN port.
2. Please connect the power adapter properly to a power socket with provided
power cable, and then connect the other end of the power adapter to the DC
48V port of the RNWA-PoE-100.
3. Connect the POWER+DATA OUT port of the RNWA-PoE-100 to a PD or a
PoE Splitter with CAT 5 UTP cable.
Now, the device can work normally with data and power.
Here are some setup examples for the PoE Injector:
PoE Injector with the devices that support PoE:
6
PoE Injector RNWA-PoE-100 User Manual
3.1 Wired Setup
7
PoE Injector RNWA-PoE-100 User Manual
3.2 Wireless Setup
Thank you for purchasing a quality Rosewill Product.
Please register your product at: www.rosewill.com for complete warranty information
and future support for your product.
Let us know!
Rosewill Support: techsupport@rosewill.com
Call Center: (800)575-9885
Web: http://www.rosewill.com
8
Loading...