Page 1
Page 2
2
The RFS-105 / RFS-108 is a high-performance Fast Ethernet
switch, with all ports capable of 10 or 100Mbps
auto-negotiation operation.
Store-and-forward switching mode promises the low l atency
plus eliminates all the network errors, including runt and CRC
error packets. To work under full-duplex mode, transmission
and reception of the frames can occur simultaneously without
causing collisions as well as double the network bandwidth.
The switch is plug-n-play with no required software to
configure and fully compliant with all kinds of network
protocols. Moreover, the rich diagnostic LEDs on the
front-panel can provide the operating status of individual port
and whole system.
RFS-105 Features:
5x 10/100Mbps RJ-45 Nway ports
Supports 802.3az Green Ethernet: Detecting port
usage power saving and cable length power saving
Supports NWay protocol for speed (10/100Mbps)
and duplex mode (Half/Full) auto-detection
Supports MDI/MDI-X auto crossover
Supports full and half duplex operation on all ports
Supports back-pressure (half duplex) and flow
control (IEEE 802.3x)
Wire-speed packet filtering and forwarding rate
Store-and-forward architecture filters fragment &
CRC error packets
Supports 1K MAC address entries in whole system
384K bits (48KB) buffer memory
FCC Class B, CE
Page 3
3
RFS-108 Features:
8 x 10/100Mbps RJ-45 Nway ports
Supports 802.3az Green Ethernet: Detecting port
usage power saving and cable length power saving
Supports NWay protocol for speed (10/100Mbps)
and duplex mode (Half/Full) auto-detection
Supports MDI/MDI-X auto crossover
Supports full and half duplex operation on all ports
Supports back-pressure (half duplex) and flow
control (IEEE 802.3x)
Supports 802.11p QoS data management
Wire-speed packet filtering and forwarding rate
Store-and-forward architecture filters fragment &
CRC error packets
Supports 1K MAC address entries in whole system
768K bits (96KB) buffer memory
FCC Class B, CE
Before you start to install the switch, check the following
contents in this package：
A 5 port RFS-105 switch or a 8 port RFS-108 switch
One external power adapter
User’s manual
Page 4
4
LED
Status
Operation
Power
Steady Green
Power is on
Off
Power is off
Link/Act
Steady Green
The port is connected
Blinking Green
The port is transmitting/receiving
data.
Off
No connection
Please refer to the following table for LED definition
5port
8port
Connect each station to the switch by twisted-pair cable.
Plug one RJ-45 connector into a RJ-45 port of the switch,
and plug the other RJ-45 connector into the station’s network
adapter. Power on the switch and then system is ready.
For cable selection, refer to the following table.
Page 5
5
Network Speed
Cable Type
Max. Length
10Mbps
Cat. 3, 4, 5 UTP/STP
100 meters
100Mbps
Cat. 5 UTP/STP
100 meters
In making a switch interconnection, you could use any port to
connect another switch with straight or crossover cable. As
all the ports support auto MDI / MDI-X function, using a
straight cable to make a switch-to-switch connection is
allowed.
For cable selection, refer to the following table：
Page 6
6
RFS-105 Spec
Switch Type
Desktop
Standards
802.3 Ethernet, 802.3u Fast
Ethernet, 802.3x Full-Duplex
Flow Control, 802.3az Energy
Efficient Ethernet
Network Management
Type
Unmanaged
Ports
5 x RJ45
Speed
10/100Mbps
MAC Address Table
1K
Buffer Memory
384K bits (48KB)
Switching Method
Store and Forward
LEDs
System: Power
Port: Link/Act
Power
External Power 5V0.6A
Dimensions
4.76" x 2.95" x 1.02" (121 x
75 x 26 mm)
Weight
0.57 lbs. (258.55g)
Temperature
0ºC to 40ºC (32ºF to 104ºF)
Humidity
10% - 90%, Non-condensing
Page 7
7
RFS-108 Spec
Switch Type
Desktop
Standards
802.3 Ethernet, 802.3u Fast
Ethernet, 802.3x Full-Duplex
Flow Control, 802.3az Energy
Efficient Ethernet, 802.1p
QoS data management
Network Management
Type
Unmanaged
Ports
8 x RJ45
Speed
10/100Mbps
MAC Address Table
1K
Buffer Memory
768K bits (96KB)
Switching Method
Store and Forward
LEDs
System: Power
Port: Link/Act
Power
External Power 5V0.6A
Dimensions
6.08" x 2.95" x 1.02" (155 x
75 x 26 mm)
Weight
0.76 lbs. (345g)
Temperature
0ºC to 40ºC (32ºF to 104ºF)
Humidity
10% - 90%, Non-condensing
Page 8
8
FCC Certifications
This Equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio
communications.
Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to correct
the interference at his own expense.
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference
received; including interference that may cause undesired operation.
CE Mark Warning
This equipment complies with the requirements relating to
electromagnetic compatibility, EN 55022 class B for ITE, the essential
protection requirement of Council Directive 2004/108/EC on the
approximation of the laws of the Member States relating to
electromagnetic compatibility.
Company has an on-going policy of upgrading its products and it may
be possible that information in this document is not up-to-date. Please
check with your local distributors for the latest information. No part of
this document can be copied or reproduced in any form without written
consent from the company.
Trademarks:
All trade names and trademarks are the properties of their respective
companies.
Copyright © 2012, All Rights Reserved.
Loading...